• 한국응급구조학회지
• /
• 제14권3호
• /
• pp.71-81
• /
• 2010

Purpose: To minimize an interruption in chest compression, reduce the hands-off time, the American Heart Association has recommended the ratio of chest compression to ventilation ratio to 30:2 from 2005 CPR guideline to 2010 CPR guideline. However, current studies have shown that the hands-off time was > 10 seconds with that method. For this reason, we devised new CPR method that a ventilation to chest compression ratio of 2:30 to reduce pt assessment time and skipped the assessment step of carotid artery pulse would be a more effective way to reduce the hands-off time & the time to set the CPR. According to the more detailed purpose are listed below. 1) We would like to confirm efficiency of a ventilation to chest compression ratio of 2:30 than a chest compression to ventilation ratio of 30:2 to reduce the hands-off time & the time to set the CPR. 2) We would like to evaluate possibility of increasing for chest compression accuracy of a ventilation to chest compression ratio of 2:30 than a chest compression to ventilation ratio of 30:2 3) We would like to evaluate possibility of increasing for ventilation accuracy of a ventilation to chest compression ratio of 2:30 than a chest compression to ventilation ratio of 30:2 Methods: According to 2005 American Heart Association Guidelines, 60 paramedic students(20 students X freshmen, sophomore, junior) performed 5 cycles of 3~ chest compressions : 2 ventilations after A, B, C evaluation with Laerdal Resusci R Anne SkillReporters. After 5 minutes rest, the 60 students performed 5 cycles of 2 ventilations : 30 chest compressions after A, B evaluation with the manikins between 13 and 17 September 2010. The short reports including speed & accuracy of chest compression, respiratory, CPR cycle were gained from the manikins. Hands-off times were measured by assistants. Results: Recently, the importance of high quality CPR was emphasized in order to perform the CPR faster and more accurate. To find out improving the conventional CPR method, we switch the procedure of the compression and the ventilation. By switching the procedure back and forth, we are able to compare the effectiveness of CPR between two type of CPR method which are 2:30 and 30:2 methods. 2:30 is that the breaths is delivered twice, first and perform 30 compressions while 30:2 perform 30 compressions first and give 2 breaths followed by the ABC method. Also, we verify the effectiveness of the hands off time, compression accuracy of the compression through the comparison of the two procedure as mentioned earlier. Consequently research verified that 2:30 is the efficient by providing faster set up delivering more accurate chest compression. Conclusion: 2:30 can minimize a time delay from cardiac standstill until starting the chest compression. In addition, hands-off time which is an interruption in chest compression can be shortened by 2:30 method, which result to effective oxygenation of coronary artery & maintenance of the bloodstream. Once again, performing the 2:30 method provide lessen hands off time and increase the accuracy of the chest compression.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제10권10호
• /
• pp.5063-5073
• /
• 2016

In this paper, an efficient texture compression method is proposed for fast rendering, which exploits the spatial correlation among blocks through intra-picture block matching. Texture mapping is widely used to enhance the visual quality of results in real-time rendering applications. For fast texture mapping, it is necessary to identify an effective trade-off between compression efficiency and computational complexity. The conventional compression methods utilized for image processing (e.g., JPEG) provide high compression efficiency while resulting in high complexity. Thus, low complexity methods, such as ETC1, are often used in real-time rendering applications. Although these methods can achieve low complexity, the compression efficiency is still lower than that of JPEG. To solve this problem, we propose a texture compression method by reducing the spatial redundancy between blocks in order to achieve the better compression performance than ETC1 while maintaining complexity that is lower than that of JPEG. Experimental results show that the proposed method achieves better compression efficiency than ETC1, and the decoding time is significantly reduced compared to JPEG while similar to ETC1.

• Journal of Advanced Marine Engineering and Technology
• /
• 제33권6호
• /
• pp.835-842
• /
• 2009

The present thesis carried out a research on a compression pressure's reduction phenomenon and its countermeasure according to the thermal efficiency improvement method by a Miller method in 4-cycle low speed diesel engine. In case of retardation of intake valve closing time in a engine, the theoretical heat efficiency shows a remarkably reducing trend when a compression ratio is not compensated. Accordingly, the thermal efficiency showed an increasing trend in case of compensating the compression ratio. Especially, it could be understood that the theoretical heat efficiency at near ABDC $100^{\circ}$ of intake valve closing time in case of compensation of the compression ratio was improved by around 25.1%, and the mean effective pressure was also increased by around 18.6%. Also, as the retardation of intake valve closing time increases, air quantity becomes insufficient due to a backflow phenomenon of intake air and thus thermal efficiency was decreased in a high load operation domain. The solving method of this problem is possible by supercharge. Therefore, in order to improve thermal efficiency by retardation of ntake valve closing time, the thermal efficiency improvement according to low compression is possible when there are a compensation device of a compression ratio and a supercharge device. This is a problem-solving method of low compression and high expansion cycle.

• Journal of Computing Science and Engineering
• /
• 제10권2호
• /
• pp.68-73
• /
• 2016

An efficient texture compression method is proposed based on a block matching process between the current block and the previously encoded blocks. Texture mapping is widely used to improve the quality of rendering results in real-time applications. For fast texture mapping, it is important to find an optimal trade-off between compression efficiency and computational complexity. Low-complexity methods (e.g., ETC1 and DXT1) have often been adopted in real-time rendering applications because conventional compression methods (e.g., JPEG) achieve a high compression ratio at the cost of high complexity. We propose a block matching-based compression method that can achieve a higher compression ratio than ETC1 and DXT1 while maintaining computational complexity lower than that of JPEG. Through a comparison between the proposed method and existing compression methods, we confirm our expectations on the performance of the proposed method.

• 한국정보과학회논문지:소프트웨어및응용
• /
• 제37권11호
• /
• pp.851-858
• /
• 2010

대부분의 휴대기기는 보조 기억장치로 NAND flash 메모리를 사용하고 있다. 또한, firmware의 크기를 줄이고 NAND flash로부터 주기억장치로 로딩하는 시간을 줄이기 위해서 압축된 코드를 NAND flash에 저장한다. 특히, 압축된 코드는 매우 빠르게 해제가 되어야 demand paging 이 적용 가능하게 된다. 본 논문에서는 이를 위하여 새로운 사전식 압축 알고리즘을 제안한다. 이 압축방식은 기존의 LZ형식과는 다르게 현재 압축하고자 하는 명령어(instruction)가 참조된 명령어와 같지 않을 경우, 프로그램 코드의 명령어의 특성을 이용하여 두 명령어의 배타 논리합(exclusive or) 값을 저장하는 방식이다. 또한, 압축 해제 속도를 빠르게 하기 위해서, 비트 단위의 연산을 최소화한 압축형식을 제공한다. 실험결과 zlib과 비교해서 최대 5배의 압축해제 속도와 4%의 압축률 향상이 있었으며, 이와 같이 매우 빠른 압축해제 속도에 따라 부팅 (booting) 시간이 10~20% 단축되었다.

• 한국컴퓨터정보학회논문지
• /
• 제18권10호
• /
• pp.55-61
• /
• 2013

패킷헤더의 중복된 필드를 제거하여 헤더의 사이즈를 줄이는 방법을 헤더압축이라고 할 때, 헤더에서 연속된 패킷간 일정 수치만큼씩 고정적으로 증가되는 Dynamic필드를 어떻게 고효율로 압축할 수 있느냐가 헤더압축의 중요한 이슈라고 할 수 있다. RTP프로토콜의 헤더 사이즈를 압축하는 기존의 방법으로 RFC2507, RFC3095 그리고 ROHC와 E-ROHC 등의 기법이 있다. 본 논문에서는 RTP 패킷의 Dynamic필드인 TS필드를 BCB(Basic Compression Bits) 기본 비트로 압축하거나 또는 NCB(Negotiation Compression Bits, BCB + 추가적인 비트) 비트로 압축하는 기존 방법보다 향상된 방법(Enhanced Method)을 제안하였다. 여기에서 제안한 새로운 향상된 헤더압축 기법의 성능을 검증하기 위해, 제안한 방식의 비디오패킷을 대상으로 Visual SLAM을 사용하여 시뮬레이션 하였다.

• 대한임베디드공학회논문지
• /
• 제18권1호
• /
• pp.1-7
• /
• 2023

In this paper, we implement a lossless compression technique for time-series data generated by IoT (Internet of Things) devices to reduce the disk spaces. The proposed compression technique reduces the size of the encoded data by selectively applying CNN (Convolutional Neural Networks) or Delta encoding depending on the situation in the Forecasting algorithm that performs prediction on time series data. In addition, the proposed technique sequentially performs zigzag encoding, splitting, and bit packing to increase the compression ratio. We showed that the proposed compression method has a compression ratio of up to 1.60 for the original data.

• 한국정보처리학회논문지
• /
• 제4권8호
• /
• pp.2133-2142
• /
• 1997

프랙탈 영상압축은 블록단위의 비교방식을 사용함으로써 기존의 압축 방법에 비해 획기적으로 증대된 압축율을 보인다. 소프트웨어에 의한 실시간대 재생이 가능함에도 불구하고 프랙탈 영상압축의 실용화에 관건이 되는 것은 압축에 소요되는 시간이다. 본 논문에서는, i)영상내부의 차원정보 추출 및 군집화에 의해 유사블럭 탐색 횟수를 줄임으로써 압축에 소요되는 시간을 최소화시키는 알고리즘과 ii)영상내부의 휘도 및 명암대비 정보를 사용하여 재생영상의 화질을 증가시키는 알고리즘을 제안하고 검증함으로써, 고속이면서도 상대적으로 고화질을 유지할 수 있는 방법을 제시하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.199-203
• /
• 1995

The technology of Semi-Solid Forging (SSF) has been actively developed to fabricate near-net- shape products using light and hardly formable materials, the SSF process is composed of slug heating, forming, compression holding and ejecting step. After forming step in SSF, the slug is compressed during a certain holding time in order to be completely filled in the die cavity and be accelerated in solidification rate. The compression holding time that can affect mechanical properties and shape of products is important to make decision, where it is necessary to find overall hert transfer coefficeient properly which has large effect on heat transfer between slug and die. This paper presents the procedure to predict compression holding time of octaining the final shaped part with information of temperature and solid fraction for a cylindrical slug at compression hoiding step in closed-die compression process using heat transfer analysis considering latent heat by means of finite element method. The influence of the predicted compression hoiding time on mechanical properties of products is finally investigated by experiment.

• 대한전기학회논문지:전력기술부문A
• /
• 제53권11호
• /
• pp.581-588
• /
• 2004

Power qualify monitoring system is devoted to more concern than before, because the innovation of industrial technology needs more accurate instruments and more advanced power quality. This paper was studied on using data of the protective relay by Power Quality Monitor. This paper was proposed the wave storage condition and monitoring clauses of the protective relay as a power quality monitoring device. The protective relay will have problem to save data for PQM analysis because the protective relay memory is limited. Therefore this paper was proposed new a data compression of data got from the protective relay. This method is wave compression comparison algorithm using the DFT. The compression rate is higher than any other established method. This method can be real time storage. This algorithm is verified using the comparison among other compression rate and proved by Real Time Digital Simulator (RTDS).