• Journal of the Optical Society of Korea
• /
• v.20 no.3
• /
• pp.435-440
• /
• 2016

We developed a simple and real-time readout autocorrelator for several tens and sub-10fs pulses, based on the two photon absorption phenomena of a commercial GaP photodetector including a transimpedance amplifier. With a suitable gain adjustment, we demonstrated that the interferometric autocorrelation for sub-nJ pulses delivered as a high output voltage as to resolve all fringes in an autocorrelation trace with features of low noise and a low offset voltage. By fitting the measured quadratic power dependence of output voltages, we obtained the quantum efficiency of TPA for the GaP detector comparable with those of a GaAsP diode and an SHG with a thin BBO crystal. The autocorrelator of a TPA based GaP photodetector is highly suitable for sensitively measuring a few cycle pulses with a broad spectral distribution from 600 nm to 1100 nm.

• Proceedings of the Optical Society of Korea Conference
• /
• 2008.02a
• /
• pp.293-294
• /
• 2008

Using bi-direction SOA based Extension system, FTTH can enhance PON system by increasing both the upstream and downstream link budget. This increased link budget can be used to extend the distance, increase the split ratio or both. The bi-direction SOA regenerates signals using all-optical amplification, and is therefore transparent to data rate or protocol. The bi-direction SOA supports legacy as well as future FTTx standards. This is based on SOA's proprietary technology platform for the manufacturing of advanced discrete photonics and photonic integrated circuits (PICs). Because the bi-direction SOA uses the same InP semiconductor technology used in virtually all telecom lasers, it is able to amplify signals at 1310 and 1490 nm, wavelengths not accessible with commercial fiber-amplifier (EDFA) technology. Due to the extremely fast response time of the InP semiconductor optical amplifiers inside, the SOA can accommodate both continuous (downstream) and bursty (upstream) traffic.

• Journal of the Semiconductor & Display Technology
• /
• v.15 no.2
• /
• pp.55-60
• /
• 2016

This study was developed through the secondary battery module charging/discharger possible utilization in the production process equipment circuit. The developed module is ensuring construction of efficient and productive charging and discharger through this research a limit on the yield and the price of existing single -channel charge and discharger circuit as a 5V 70A grade secondary battery Formation charge and discharger for up to 1 board 4 channels. In order to improve the sensing accuracy, through a robust differential amplifier circuit described using 16bit Analog-Digital Converter and noise was secured 16bit resolution sensing. The configuration also made demands for property Rise / Fall Time. Data Acquisition, discharge efficiency and also to fit the sink circuit temperature level for mass production.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.5
• /
• pp.49-54
• /
• 2013

We designed a burst mode optical receiver for 1.25Gbps PON(Passive Optical Network), fabricated it using $0.8{\mu}m$ BiCMOS foundry. We minimized the loss of the data in the front of the burst by reducing AGC(Automatic Gain Control) signal generation time using an exponential amplifier. We confirmed that AGC of the burst mode optical receiver functioned well and showed good performance in measurement. However, although the eye of the eye pattern was opened the jitter characteristic was deteriorated due to the heavy waveform distortion.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.4
• /
• pp.78-83
• /
• 1996

A timing recovery circuit of 10 Gbit/s optical receiver is described. The circuit consists of a passive NRZ-to-PRZ circuit, a dielectric resonator filter (DRF) and a narrow band amplifier, which for the first time adopted a temperature compensation technique using the tempareature characteristics of DR. The experimental results showed an output clock phase variation of less than ${\pm}$6 degree over the operating temperature range form 0$^{\circ}C$ to 75$^{\circ}C$ and measured maximum rms jitters of less than 2 phs with the resonance detunings of up to ${\pm}$10 MHz. These experimental results show that the circuit is a suitable for 10 Gbit/s lightwave transmission system.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.417-420
• /
• 2007

A 12k-bit SRAM has been developed for line memory of system-on-glass (SoG) with lowtemperature poly-silicon (LTPS) thin film transistor (TFT). For accurate sensing even with the large variation and mismatches in the characteristics of LTPS TFT, mismatch immune sense amplifier is developed. The SRAM shows 30ns read access time with 7V supply voltage while dissipating 4.05mW and 1.75mW for write and read operation, respectively

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1593-1595
• /
• 2000

We present a new procedure to evaluate the degradation in a lCr-lMo-0.25V steel. The method is based on the existence of the peak of reversible permeability in the differential magnetization around the coercive field strength. The apparatus is based on the detection of the voltage induced in a surface type coil using a lock-in amplifier tuned to a frequency to the exciting one. Results obtained the reversible permeability and Vickers hardness on the annealed samples show the peak interval of reversible permeability and Vickers hardness decreased as ageing time increased. The correlation between Vickers hardness and the peak interval of reversible permeability could well be evaluated non destructively.

• Proceedings of the KSR Conference
• /
• 2005.11a
• /
• pp.777-782
• /
• 2005

In this paper, we designed and fabricated a partial discharge (PD) detector to diagnose the soundness of CNCV cables by analyzing PD pulses and to predict discharge locations. The PD detector is consisted of a coupling network with a discharge free capacitor and a detection impedance, a voltage follower and a low noise amplifier. Lower cut-off frequency of the detector is adjusted at 175kHz to block AC voltage and to pass discharge pulse only. The discharge location could be obtained by the time of arrival method using travelling wave propagation theory. In a laboratory test on an eighty meter CV cable, we could position the discharge location within a two meter error.

• ETRI Journal
• /
• v.32 no.4
• /
• pp.503-511
• /
• 2010

WiBro radio frequency (RF) repeater is used for solving the problem of partial shadow areas in the wireless communication field that uses time-division duplexing (TDD) mode. In this paper, a method to efficiently generate TDD signals for WiBro RF repeater is proposed and its digital circuit is implemented. A TDD signal is detected from RF signals transmitted/received to/from RF repeater and then inputted again into the RF repeater, so that it can operate normally. First, the envelope of downlink signals is detected and then clamped to extract the basic form of a TDD signal using an operational amplifier circuit. Next, the TDD signal is generated by restoring and filtering the shape which has been distorted by the wireless channel. The algorithm and system to acquire TDD signal are developed with a goal to have simple but powerful functions with as little cost as possible. The proposed method is implemented as an RF-digital integrated system and verified through the experiments under the same condition as actual WiBro service environment.

• Journal of Sensor Science and Technology
• /
• v.8 no.3
• /
• pp.259-264
• /
• 1999

The $CO_2$ measuring system using infrared sensor has the variance according to the temperature change. Therefore, the temperature compensation should be needed to obtain a reliable measurement. In this study, the sensor module consist of infrared $CO_2$ Sensor, IR Source, pipe and the heater and measuring system has amplifier, A/D converter and microprocessor. And we suggest a method to reduce the error by using the PID temperature control. We use optimum parameters setting of Ziegler & Nichols as well as PID temperature control algorithm for the temperature compensation. In this method, PID optimum parameter is set from dummy time(L) and maximum slope(R). As a result of using this PID temperature control, it is founded that it has the fast response and low steady state error. Therefore, it is certainly proved that this is very suitable algorithm to correct the error on measurement.