• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제14권10호
• /
• pp.802-807
• /
• 2001

The (S $r_{0.85}$C $a_{0.15}$)Ti $O_{3}$(SCT) thin films are deposited on Pt-coated electrode (Pt/TiN/ $SiO_2$/Si) using RF sputtering method. The composition of SCT thin films deposited on Si substrate at woom temperature is close to stoichiometry(1.102 in A/B ratio). The maximum dielectric constant of SCT thin films is obtained by annealing at 600[$^{\circ}C$]. The capacitance characteristics had a stable value within $\pm$4[%]. The drastic decrease of dielectric constant and increase of dielectric loss in SCT thin films is observed above 200[kHz]. SCT thin films used in this study show the phenomena of dielectric relaxation with the increase of frequencey.cey.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 1987년도 정기총회 및 창립40주년기념 학술대회 학회본부
• /
• pp.207-209
• /
• 1987

This paper reports the effect of additive elements such as Bi, Sb on degradation and hole formation of the Te-Se thin films. Changes in light transmission were used to monitor the degradation rate of thin Te films in an accelerated temperature-humidity environment. In thin accelerated temperature-humidity environment, $(Te_{86}Se_{14})_{70}Bi_{30}$ thin film was stable and $(Te_{86}Se_{14})_{50}Sb_{50}$ thin film was unstable in comparison with the other films that used in this experiment. The hole formation was carried out in the Te-based thin films.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• 제52권10호
• /
• pp.436-440
• /
• 2003

The (S $r_{0.85}$C $a_{0.15}$)Ti $O_3$(SCT) thin films were deposited on Pt-coated electrode(Pt/TiN/ $SiO_2$/Si) using RF sputtering method according to the deposition condition. The optimum conditions of RF power and Ar/ $O_2$ ratio were 140[W] and 80/20, respectively. Deposition rate of SCT thin films was about 18.75[$\AA$/min] at the optimum condition. The composition of SCT thin films deposited on Si substrate is close to stoichiometry (1.102 in A/B ratio). The capacitance characteristics had a stable value within $\pm$4[%]. The drastic decrease of dielectric constant and increase of dielectric loss in SCT thin films were observed above 200[kHz]. SCT thin films used in this study showed the phenomena of dielectric relaxation with the increase of frequency.ncy.

• Korean Journal of Materials Research
• /
• 제17권4호
• /
• pp.232-235
• /
• 2007

Indium tin oxide (ITO) films were deposited on polycarbonate CR39 substrate using DC magnetron sputtering. ITO thin films were deposited at room temperature because glass-transition temperature of CR39 substrate is $130^{circ}C$ ITO thin films are used as bottom and top electrodes and for organic thin film transparent transistor (OTFT). The electrodes electrical properties of ITO thin films and their optical transparency properties in the visible wavelength range (300-800 nm) strongly depend on the volume of oxygen percent. The optimum resistivity and transparency of ITO thin film electrode was achieved with a 75 W plasma power, 10 % volume of oxygen and a 27 nm/min deposition rate. Above 85% transparency in the visible wavelength range (300-800 nm) was measured without post annealing process, and resistivity as low as $9.83{\times}^{TM}10^{-4}{\Omega}$ cm was measured at thickness of 300 nm.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 C
• /
• pp.1500-1501
• /
• 2006

Because AZO thin film has the potential applications, Preparing AZO thin films on the polymer substrate has been widely studied. In this study, we prepared AZO thin films on polyethersulfon (PES) at room temperature. The AZO thin films were prepared at $O_2$ gas flow rate of 0.05 and sputtering power of 100W with different film thickness by facing targets sputtering method. The electrical, optical and crystallographic properties of AZO thin films were measured by Hall effect measurement system, UV/VIS spectrometer, SEM and XRD. From the results, we obtained AZO thin films with a low resistivity, a transmittance of over 80% and c-axis preferred orientation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.24-24
• /
• 2007

Aerosol deposition(AD) method is a emerging technology for the room temperature deposition of the dielectric thin films with high quality. In this study, $Al_2O_3$ thin films were deposited by aerosol deposition method directly from raw powders. To get uniform and smooth film surface, Process parameters such as gas consumption rate, nozzle-substrate distance and vibration speed were optimized. From XRD results, $Al_2O_3$ thin films have the same crystal structures with starting powders. $Al_2O_3$ thin films also showed dense microstructure. Electrical properties of the thin films were also investigated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.739-742
• /
• 2000

Nanostructured ZnS thin films were grown on the slide glass substrate by the chemical bath deposition using an aqueous so1ution Of ZnSO$_4$and CH$_3$CSNH$_2$at 95$^{\circ}C$. The average grain sizes of the ZnS thin film estimating from the Debye-Scherrer formula are 4.8 nm. The optical transmittance edge of the ZnS thin films (4.0 eV) was shifted to the shelter wavelength compared with that of the bulk ZnS (3.67 eV) due to the quantum size effects. The ZnS thin films showed a strong photoluminescence intensity and a sharp emission band from 410 to 480 nm 3t room temperature. The PWHM of photoluminescence peak was about 40 nm. For the viloet(410 nm) and blue(480 nm) emission of the ZnS thin films, the temperature dependence can be described by an Arrhenius equation with an activation energy of 168 and 157 meV, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.254-255
• /
• 2012

Interest in nano-crystalline silicon (nc-Si) thin films has been growing because of their favorable processing conditions for certain electronic devices. In particular, there has been an increase in the use of nc-Si thin films in photovoltaics for large solar cell panels and in thin film transistors for large flat panel displays. One of the most important material properties for these device applications is the macroscopic charge-carrier mobility. Hydrogenated amorphous silicon (a-Si:H) or nc-Si is a basic material in thin film transistors (TFTs). However, a-Si:H based devices have low carrier mobility and bias instability due to their metastable properties. The large number of trap sites and incomplete hydrogen passivation of a-Si:H film produce limited carrier transport. The basic electrical properties, including the carrier mobility and stability, of nc-Si TFTs might be superior to those of a-Si:H thin film. However, typical nc-Si thin films tend to have mobilities similar to a-Si films, although changes in the processing conditions can enhance the mobility. In polycrystalline silicon (poly-Si) thin films, the performance of the devices is strongly influenced by the boundaries between neighboring crystalline grains. These grain boundaries limit the conductance of macroscopic regions comprised of multiple grains. In much of the work on poly-Si thin films, it was shown that the performance of TFTs was largely determined by the number and location of the grain boundaries within the channel. Hence, efforts were made to reduce the total number of grain boundaries by increasing the average grain size. However, even a small number of grain boundaries can significantly reduce the macroscopic charge carrier mobility. The nano-crystalline or polymorphous-Si development for TFT and solar cells have been employed to compensate for disadvantage inherent to a-Si and micro-crystalline silicon (${\mu}$-Si). Recently, a novel process for deposition of nano-crystralline silicon (nc-Si) thin films at room temperature was developed using neutral beam assisted chemical vapor deposition (NBaCVD) with a neutral particle beam (NPB) source, which controls the energy of incident neutral particles in the range of 1~300 eV in order to enhance the atomic activation and crystalline of thin films at room temperature. In previous our experiments, we verified favorable properties of nc-Si thin films for certain electronic devices. During the formation of the nc-Si thin films by the NBaCVD with various process conditions, NPB energy directly controlled by the reflector bias and effectively increased crystal fraction (~80%) by uniformly distributed nc grains with 3~10 nm size. The more resent work on nc-Si thin film transistors (TFT) was done. We identified the performance of nc-Si TFT active channeal layers. The dependence of the performance of nc-Si TFT on the primary process parameters is explored. Raman, FT-IR and transmission electron microscope (TEM) were used to study the microstructures and the crystalline volume fraction of nc-Si films. The electric properties were investigated on Cr/SiO2/nc-Si metal-oxide-semiconductor (MOS) capacitors.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.208-208
• /
• 2010

Indium zinc tin oxide (IZTO) thin films were studied as a possible alternative to indium tin oxide (ITO) films for providing low-cost transparent conducting oxide (TCO) for thin film photovoltaic devices. IZTO films were deposited onto glass substrates at room temperature. A dc/rf magnetron co-sputtering system equipped with a ceramic target of the same composition was used to deposit TCO films. Earlier studies showed that the resistivity value of $In_{0.6}Zn_{0.2}Sn_{0.2}O_{1.5}$ (IZTO20) films could be lowered to approximately $6{\times}10^{-4}ohm{\cdot}cm$ without sacrificing optical transparency and still maintaining amorphous structure through the optimization of process variables. The growth rate was kept at about 8 nm/min while the oxygen-to-argon pressure ratio varied from 0% to 7.5%. As-deposited films were always amorphous and showed strong oxygen pressure dependence of electrical resistivity and electron concentration values. Influence of forming gas anneal (FGA) at medium temperatures was also studied and proven effective in improving electrical properties. In this study, the chemical composition of the targets and the films varied around the $In_{0.6}Zn_{0.2}Sn_{0.2}O_{1.5}$ (IZTO20). It was the main objective of this paper to investigate how off-stoichiometry affected TCO characteristics including electrical resistivity and optical transmission. In addition to the composition effect, we have also studied how film properties changed with processing variables. IZTO thin films have shown their potential as a possible alternative to ITO thin films, in such way that they could be adopted in some applications where currently ITO and IZO thin films are being used. Our experimental results are compared to those obtained for commercial ITO thin films from solar cell application view point.

• Korean Journal of Optics and Photonics
• /
• 제17권1호
• /
• pp.104-109
• /
• 2006

Cu-doped $TiO_2$ thin films were prepared by RF magnetron co-sputtering, and their structural, optical and photodegradation. properties were examined as a function of calcination temperature. XRD results showed that the crystallite size of Cu/$TiO_2$ thin films was bigger than that of the pure $TiO_2$ thin films. SEM results revealed that the agglomerated particle size of the Cu/$TiO_2$ films was more uniform and smaller than that of pure $TiO_2$ films. The absorption edge of thin films calcined at $900^{\circ}C$ was red shifted, resulting from the phase transformation from anatase to rutile phase, and the transmittance of the thin film rapidly decreased due to an increase in particle size. The photodegradation properties of the Cu/$TiO_2$ thin films were superior to those of the pure $TiO_2$ thin films.