• Structural Engineering and Mechanics
• /
• v.21 no.6
• /
• pp.635-658
• /
• 2005

The possibility of detecting a crack in L-shaped pipes filled with fluid based on measurement of transverse natural frequencies is examined. The problem is solved by representing the crack by a massless rotational spring, simulating the out-of-plane transverse vibration only without solving the coupled torsional vibration and using the transfer matrix method for solution of the governing equation. The theoretical solutions are verified by experiments. The cracks considered are external, circumferentially oriented and have straight front. Pipes made of aluminium and mild steel are tested with water as internal fluid. Crack size to pipe thickness ratio ranging from 0.20 to 0.57 and fluid (gauge) pressure in the range of 0 to 10 atmospheres are examined. The rotational spring stiffness is obtained by an inverse vibration analysis and deflection method. The details of the two methods are given. The results by the two methods are presented graphically and show good agreement. Crack locations are also determined by the inverse analysis. The maximum absolute error in the location is 13.80%. Experimentally determined variation of rotational spring stiffness with ratio of crack size to thickness is utilized to predict the crack sizes. The maximum absolute errors in prediction of crack size are 17.24% and 16.90% for aluminium and mild steel pipes respectively.

• Archives of Plastic Surgery
• /
• v.46 no.2
• /
• pp.167-170
• /
• 2019

Full-thickness scalp burns secondary to hair coloring are rare; however, such defects can be large and complex reconstruction of hair-bearing tissue may be necessary. Many skin-stretching devices that use gradual traction have been applied to take advantage of the viscoelastic properties of the skin. A 21-year-old female patient was seen with a burn defect on her occipital scalp leading to exposed subcutaneous tissue after chemical application of hair coloring in a salon. The dimensions of the wound were $10cm{\times}5cm$, and a skin graft or flap would have been necessary to close the defect. Two long transfixing K-wires (1.4 mm) and paired 3-wire threads (23 gauge), which are readily available in most hospitals, were applied over a period of 12 days for trichophytic closure of the defect. The remaining scalp scars after primary trichophytic closure with this skin-stretching method were refined with hair follicle transplantation. This skin-stretching method is simple to apply and valuable for helping to close problematic areas of skin shortage that would otherwise require more complicated procedures. This case shows a relatively unknown complication of hair coloring and its treatment.

• Nuclear Engineering and Technology
• /
• v.54 no.12
• /
• pp.4481-4490
• /
• 2022

In this study, a new rupture disk corrosion test (RDCT) method was developed for real-time detection of stress corrosion cracking (SCC) initiation of Alloy 600 in a primary water environment of pressurized water reactors. In the RDCT method, one side of a disk specimen was exposed to a simulated primary water at high temperature and pressure while the other side was maintained at ambient pressure, inducing a dome-shaped deformation and tensile stress on the specimen. When SCC occurs in the primary water environment, it leads to the specimen rupture or water leakage through the specimen, which can be detected in real-time using a pressure gauge. The tensile stress applied to the disk specimen was calculated using a finite element analysis. The tensile stress was calculated to increase as the specimen thickness decreased. The SCC initiation time of the specimen was evaluated by the RDCT method, from which result it was found that the crack initiation time decreased with the decrease of specimen thickness owing to the increase of applied stress. After the SCC initiation test, many cracks were observed on the specimen surface in an intergranular fracture mode, which is a typical characteristic of SCC in the primary water environment.

• Journal of Sensor Science and Technology
• /
• v.19 no.1
• /
• pp.31-35
• /
• 2010

High temperature micro pressure sensors were fabricated by using polycrystalline 3C-SiC piezoresistors grown on oxidized SOI substrates by APCVD. These have been made by bulk micromachining under $1{\times}1mm^2$ diaphragm and Si membrane thickness of $20{\mu}m$. The pressure sensitivity of implemented pressure sensors was 0.1 mV/$V{\cdot}bar$. The nonlinearity and the hysteresis of sensors were ${\pm}0.44%{\cdot}FS$ and $0.61%{\cdot}FS$. In the temperature range of $25^{\circ}C{\sim}400^{\circ}C$ with 5 bar FS, TCS (temperature coefficient of sensitivity), TCR (temperature coefficient of resistance), and TCGF (temperature coefficient of gauge factor) of the sensor were -1867 ppm/$^{\circ}C$, -792 ppm/$^{\circ}C$, and -1042 ppm/$^{\circ}C$, respectively.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1997.04a
• /
• pp.48-53
• /
• 1997

Electronic Speckle Pattern Interferometry(ESPI) using the Model 95 Ar laserm, a video system and an image processor was applied to the in-plane displacement measurements. Unlike traditional strain gauges or moire method, ESPI method requires no special surface preparation or attachments and can be measured in-plane displacement with no contact and real time. In this experiment wpecimen was loaded in parallel with a loadcell. The specimen was the cold rolled sdteel sheet of 2mm thickness, which was attached strain gauges. The study provides an example of how ESPI have been used to measure strain displacement in this specimen. The results measured by ESPI have been used to measure strain displacement in this specimen. The results measured by ESPI have been used to measure strain displacement in this specimen. The results measured by ESPI compare with the data which was measured by strain gauge method in tensile testing.

• The Journal of the Korean dental association
• /
• v.12 no.9
• /
• pp.691-694
• /
• 1974

The trends of restoration on abrased teethis mostly based on gnathology or on practical experience. This study was performed on plaster models from 60 young men whose teeth and occlusion are clinically normal. A pair, upper and lower models, were mounted on HANAU articulator. Iron ball bearing 0.2mm 0.5mm 0.7mm and 1.0mm in diameter was attached on mesiobuccal cusp of upper first molar. [table I] Long ribbon shape of cold cure resin was inserted and jaw was closed gently so as not to move disturb original position of iron ball. The resin bite registration was measured minimun thickness from each lingual cusps of upper jaw and buccal cusps of lower jaw by means of Bowley gauge. The results were as follows (graph). 1) The distance from upper lingual cusps and lower buccal cusps: backward cusps showed smaller than standard cusp (upper mesio-buccal cusp) and forward cusps showed longer than standard. 2) The measurements from upper lingual cusps are not coincide with lower buccal cusps.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.180.2-180
• /
• 2001

In the hot rolling process, the RF AGC (Roll Force Auto Gauge Control) is used to control the roll gap to reduce the variation of rolling force caused by the roll eccentricity and the variation of material thickness. However the effect of the roll eccentricity cannot be distinguished. To eliminate the effect of the roll eccentricity, the roll eccentricity estimation is needed to supplement some drawbacks of RF AGC. In this paper, an ALE(Adaptive Line Enhancer) that extracts the rolling force variation due to the roll eccentricity is suggested. We also provide an algorithm that enhances the convergence time of roll eccentricity estimation. The performance improvement of the Suggested algorithm is shown via simulations.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.150.5-150
• /
• 2001

This paper deals with a modified repetitive control method for compensating automatic gauge control (AGC) to reduce the effect of skid mark which directly influence the quality of products in plate mill process. Since the skid mark on the plate have thermal difference, it makes a different stretching rate and deflection of thickness. Firstly, the (AGC) system and the plate mill process are described by considering function in each control levels. The skid mark of the plate in practical control fields is shown. Also, its frequency variation is given by on-line FFT analysis method. Secondly, a key idea of the modified repetitive control method with time varying period disturbance is represented and compared with standard repetitive control method. Lastly, in simulation ...

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.418-421
• /
• 2001

Press brake is used as bending and forming sheet metal in vehicle and many kind of industry. This paper deals with development of NC press brake based on high precision positioning device and software, which can be operated on personal computer. In this system, positioning device is used for controlling bending angle and operated by the developed software, which is database from material property, width and thickness of material. This study will make distribution in development of computer aided press brake.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.04a
• /
• pp.171-178
• /
• 2000

In order to evaluate the tensile behaviors of hoop direction for the nuclear fuel cladding tubes the shapes of specimen and jig fixtures for the ring test are decided with various conditions under the elastic-large plastic deformations. The axial displacement of the jig cylinders is converted to the circumferential direction elongations of specimen. The stress distributions on specimen are depended on the radii and locations of specimen and jig size and central angle. Therefore we calculated the stress distributions and decided the optimum shapes to get the uniform stress in the area of specimen gage length. Form the analysis the stress distributions in gate area are reviewed with the radii and location of specimen notch and the central angle of jig cylinder,. The optimum shapes of specimen and jig are proposed to the clad tube having 10.62 mm in diameter and 0.63mm in thickness for 16x16 PWR nuclear fuel assembly.