• JSTS:Journal of Semiconductor Technology and Science
• /
• 제13권6호
• /
• pp.581-588
• /
• 2013

This paper presents a study of the process temperature dependence of $Al_2O_3$ film grown by thermal atomic layer deposition (ALD) as a passivation layer in the crystalline Si (c-Si) solar cells. The deposition rate of $Al_2O_3$ film maintained almost the same until $250^{\circ}C$, but decreased from $300^{\circ}C$. $Al_2O_3$ film deposited at $250^{\circ}C$ was found to have the highest negative fixed oxide charge density ($Q_f$) due to its O-rich condition and low hydroxyl group (-OH) density. After post-metallization annealing (PMA), $Al_2O_3$ film deposited at $250^{\circ}C$ had the lowest slow and fast interface trap density. Actually, $Al_2O_3$ film deposited at $250^{\circ}C$ showed the best passivation effects, that is, the highest excess carrier lifetime (${\tau}_{PCD}$) and lowest surface recombination velocity ($S_{eff}$) than other conditions. Therefore, $Al_2O_3$ film deposited at $250^{\circ}C$ exhibited excellent chemical and field-effect passivation properties for p-type c-Si solar cells.

• Applied Science and Convergence Technology
• /
• 제25권3호
• /
• pp.56-60
• /
• 2016

The ALD process is an adequate technique to meet the requirements that come with the downscaling of semiconductor devices. To obtain thin films of the desired standard, it is essential to understand the thermal decomposition properties of the precursors. As such, this study examined the thermal decomposition properties of TEMAHf precursors and its effect on the formation of $HfO_2$ thin films. FT-IR experiments were performed before deposition in order to analyze the thermal decomposition properties of the precursors. The measurements were taken in the range of $135^{\circ}C-350^{\circ}C$. At temperatures higher than $300^{\circ}C$, there was a rapid decrease in the absorption peaks arising from vibration of $Sp^3$ C-H stretching. This showed that the precursors experienced rapid decomposition at around $275^{\circ}C-300^{\circ}C$. $HfO_2$ thin films were successfully deposited by Atomic Layer Deposition (ALD) at $50^{\circ}C$ intervals between $150^{\circ}C$ to $400^{\circ}C$; the deposited films were characterized using a reflectometer, X-ray photoelectron spectroscopy (XPS), Grazing Incidence X-ray Diffraction (GIXRD), and atomic force microscopy (AFM). The results illustrate the relationship between the thermal decomposition temperature of TEMAHf and properties of thin films.

• 반도체디스플레이기술학회지
• /
• 제6권3호
• /
• pp.19-23
• /
• 2007

The NiSi is very promising candidate for the metallization in 45 nm CMOS process such as FUSI(fully silicided) gate and source/drain contact because it exhibits non-size dependent resistance, low silicon consumption and mid-gap workfunction. Ni film was first deposited by using ALD (atomic layer deposition) technique with Bis-Ni precursor and $H_2$ reactant gas at $220^{\circ}C$ with deposition rate of $1.25\;{\AA}/cycle$. The as-deposited Ni film exhibited a sheet resistance of $5\;{\Omega}/{\square}$. RTP (repaid thermal process) was then performed by varying temperature from $400^{\circ}C$ to $900^{\circ}C$ in $N_2$ ambient for the formation of NiSi. The process temperature window for the formation of low-resistance NiSi was estimated from $600^{\circ}C$ to $800^{\circ}C$ and from $700^{\circ}C$ to $800^{\circ}C$ with and without Ti capping layer. The respective sheet resistance of the films was changed to $2.5\;{\Omega}/{\square}$ and $3\;{\Omega}/{\square}$ after silicidation. This is because Ti capping layer increases reaction between Ni and Si and suppresses the oxidation and impurity incorporation into Ni film during silicidation process. The NiSi films were treated by additional thermal stress in a resistively heated furnace for test of thermal stability, showing that the film heat-treated at $800^{\circ}C$ was more stable than that at $700^{\circ}C$ due to better crystallinity.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.303-303
• /
• 2012

X-선 반사율 측정법(XRR)은 비파괴적인 측정방법으로 수 nm의 두께를 정밀하게 측정할 수 있는 장점으로 반도체 산업현장에서 많은 관심과 연구가 이루어지고 있다. 이러한 XRR의 두께 측정 정밀도를 향상시키고 부정확한 결과를 방지하기 위하여 측정기기를 검증하고 보정할 수 있는 두께 표준물질을 필요로 하고 있다. 본 연구에서는 IBSD (ion beam sputtering deposition)와 ALD (atomic layer deposition)를 이용하여 5 nm, 10 nm의 $HfO_2$ 박막을 제작하고, XRR용 두께 표준물질로 응용할 수 있는지를 살펴보았다. 먼저 두께표준물질로 제작하기 위해서는 박막과 기판이 안정한 상태를 유지해야 한다. 이에 박막은 공기 중 노출에 의한 산화로 박막의 두께가 변할 수 있는 금속박막 대신에 공기 중에서도 안정한 산화물 박막인 $HfO_2$ 박막을 사용하고 기판은 Si wafer를 thermal공기 중에서도 안정한 산화물 박막인 $HfO_2$ 박막을 사용하고 기판은 Si wafer를 therma oxidation법을 이용하여 $1{\mu}m$ 두께로 제작한 비정질 $SiO_2$ 기판을 사용했다. 제작된 시료의 특성평가를 위해 XRR (X-ray reflectometer) 측정을 통해 두께, 거칠기 및 밀도를 확인하였고, TEM (transmission electron microscope)으로 두께 측정을 하여 XRR로 얻은 두께결과와 비교하였다. 측정결과를 확인하였을 때 두 증착 방법 중 ALD를 이용하여 제작한 시편에서는 박막과 기판사이의 interface가 sharp하여 반사율 곡선의 진폭이 크게 잘 나타났고 fitting 결과도 우수하여 IBSD로 증착한 시편보다 두께 표준물질로 응용하기에 더 적합하였다.

• 센서학회지
• /
• 제13권3호
• /
• pp.195-198
• /
• 2004

For a diffusion barrier against copper, tantalum nitride films have been deposited on $SiO_{2}$ by atomic layer deposition (ALD), using PEMAT(Pentakis(ethylmethylamino)tantalum) and $NH_{3}$ as precursors, Ar as purging gas. The deposition rate of TaN at substrate temperature $250^{\circ}C$ was about $0.67{\AA}$ per one cycle. The stability of TaN films as a Cu diffsion barrier was tested by thermal annealing for 30 minutes in $N_{2}$ ambient and characterized through XRD, sheet resistance, and C-V measurement(Cu($1000{\AA}$)/TaN($50{\AA}$)/$SiO_{2}$($2000{\AA}$)/Si capacitor fabricated), which prove the TaN film maintains the barrier properties Cu below $400^{\circ}C$.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 추계학술대회 논문집 Vol.15
• /
• pp.47-50
• /
• 2002

ZnO nanowires were coated conformally with aluminum oxide ($Al_{2}O_{3}$) material by atomic layer deposition (ALD). The ZnO nanowires were first synthesized on a Si (100) substrate at $1380^{\circ}C$ from ball-milled ZnO powders by a thermal evaporation procedure with an argon carrier gas without any catalysts; the length and diameter of these ZnO nanowires are $20\sim30{\mu}m$ and $50{\sim}200$ nm, respectively. $Al_{2}O_{3}$ films were then deposited on these ZnO nanowires by ALD at a substrate temperature of $300^{\circ}C$ using trimethylaluminum (TMA) and distilled water ($H_{2}O$). Transmission electron microscopy (TEM) images of the deposited ZnO nanowires revealed that 40nm-thick $Al_{2}O_{3}$ cylindrical shells surround the ZnO nanowires.

• 한국분말재료학회지
• /
• 제31권3호
• /
• pp.255-262
• /
• 2024

Nano-oxide dispersion-strengthened (ODS) superalloys have attracted attention because of their outstanding mechanical reinforcement mechanism. Dispersed oxides increase the material's strength by preventing grain growth and recrystallization, as well as increasing creep resistance. In this research, atomic layer deposition (ALD) was applied to synthesize an ODS alloy. It is useful to coat conformal thin films even on complex matrix shapes, such as nanorods or powders. We coated an Nb-Si-based superalloy with TiO₂ thin film by using rotary-reactor type thermal ALD. TiO₂ was grown by controlling the deposition recipe, reactor temperature, N₂ flow rate, and rotor speed. We could confirm the formation of uniform TiO₂ film on the surface of the superalloy. This process was successfully applied to the synthesis of an ODS alloy, which could be a new field of ALD applications.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.418-418
• /
• 2012

We fabricated a new type of hybrid film using molecular layer deposition (MLD). The MLD is a gas phase process analogous to atomic layer deposition (ALD) and also relies on a saturated surface reaction sequentially which results in the formation of a monolayer in each sequence. In the MLD process, polydiacetylene (PDA) layers were grown by repeated sequential surface reactions of titanium tetrachloride and 2,4-hexadiyne-1,6-diol with ultraviolet (UV) polymerization under a substrate temperature of $100^{\circ}C$. Ellipsometry analysis showed a self-limiting surface reaction process and linear growth of the hybrid films. Polymerization of the hybrid films was confirmed by infrared (IR) spectroscopy and UV-Vis spectroscopy. Composition of the films was confirmed by IR spectroscopy and X-ray photoelectron (XP) spectroscopy. The titanium oxide cross-linked polydiacetylene (TiOPDA) hybrid films exhibited good thermal and mechanical stabilities.

• Transactions on Electrical and Electronic Materials
• /
• 제10권6호
• /
• pp.200-202
• /
• 2009

Tin oxide thin films were prepared by atomic layer deposition using a tetrakis(ethylmethylamino) tin precursor without any seed layer. The average growth rate of tin oxide film is about 1.2 A/cycle from $50{^{\circ}C}$ to $150{^{\circ}C}$. The rate decreases rapidly at a substrate temperature of $200{^{\circ}C}$. ALD-grown tin oxide thin film was characterized with the use of XRD, AFM and XPS. Due to a thermal annealing effect, the surface roughness and the tin amount in the film composition are slightly increased.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.116-116
• /
• 2007

We investigated the characteristics of the Hafnium silicate (Hf-silicate) film which is grown by ALD (atomic layer deposition). The Hf-silicate films that were annealed by the RTP. The physical and electrical properties of nitrided Hf-silicate films, incorporated by NO gas and $NH_3$ gas annealing, were investigated by XPS, TEM and I-V measurement. We confirmed the nitrogen incorporation during NO gas annealing treatment effectively enhances the thermal stability of Hf-silicate. The tendency of nitnitridation in NO gas and $NH_3$ is different. Leakage current is improved in post NO gas annealing.