• Advances in concrete construction
• /
• 제8권2호
• /
• pp.145-154
• /
• 2019

The present experimental study addresses the structural response of reinforced concrete (RC) beams strengthened in shear. Thirteen RC beams were divided into four different sets to investigate the effect of transverse and longitudinal steel reinforcement ratios, concrete compressive strength change and orientation for installing carbon fiber-reinforced polymer (CFRP) laminates. Then, we employed a shear strengthening solution through externally bonded reinforcement in grooves (EBRIG) and externally bonded reinforcement (EBR) techniques. In this regard, rectangular beams of $200{\times}300{\times}2000mm$ dimensions were subjected to the 4-point static loading condition and their load-displacement curves, load-carrying capacity and ductility changes were compared. The results revealed that using EBRIG method, the gain percentage augmented with the increase in the longitudinal reinforcement ratio. Also, in the RC beams with stirrups, the gain in shear strength decreased as transverse reinforcement ratio increased. The results also revealed that the shear resistance obtained by the experimental tests were in acceptable agreement with the design equations. Besides, the results of this research indicated that using the EBRIG system through vertical grooves in RC beams with and without stirrups caused the energy absorption to increase about 85% and 97%, respectively, relative to the control.

• 콘크리트학회논문집
• /
• 제28권5호
• /
• pp.527-534
• /
• 2016

CFRP의 전단강도 기여분을 평가하고, 모어서클을 이용하여 전단거동 특성을 분석하기 위해 전단철근비가 서로 다른 보에 동일한 탄소섬유 전단보강 설계한 보 실험을 수행하였다. 취성특성을 가지는 CFRP의 전단기여분을 평가하기 위해서는 CFRP의 변형률을 평가해야 한다. 각 실험결과는 모어써클(Mohr's Circle)을 활용하여 전단변형률을 주인장변형률 및 균열각도의 변화와 연계하여 비교하였다. 전단철근비가 작은 경우 탄소섬유 자체의 전단강도 기여분 뿐만 아니라 탄소섬유에 의해 콘크리트 균열의 진전을 제어하여 균열에 의한 콘크리트의 성능저하를 최소화한다. 전단철근비가 큰 경우는 전단철근비가 작을 때 보다 탄소섬유 보강효과가 크지 않았다. 따라서 보강부재의 전단성능을 결정할 때 탄소섬유의 전단강도 기여분은 전단철근과의 상호작용을 고려할 수 있는 변형적합조건에 근거하여 평가되어야 한다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.35-37
• /
• 2008

The light Mg alloys bearing the remarkably high strength, corrosion resistance and elevated temperature stability stand on the center of interest. The accomplishment so far is, however, only by alloy modification without any consideration on the rapid solidification effect. This work is to report not only the effect of rapid solidification of $MgZn_{4.3}Y_{0.7}$ alloy powders, but the extrusion behavior on the materials properties. The average grain size of the atomized powders was about $3-4{\mu}m$. The extrusion was carried out with the area reduction ratio of 10:1 to 15:1. As the ratio increased, homogeneous microstructure was obtained, and the mechanical properties such as tensile strength and elongation were simultaneously increased.

• 한국컴퓨터정보학회논문지
• /
• 제24권2호
• /
• pp.157-161
• /
• 2019

In this paper, the researcher investigated whether strengthening the back muscles affects the quality of chest compressions during cardiopulmonary resuscitation by university students. A total of 50 students majoring in healthcare were included from September 2018 to November. The participants performed chest compressions during cardiopulmonary resuscitation (CPR) for 2 min after back muscle strength was measured. Then, after adequate rest, the participants repeated the back muscle strength measurements and chest compressions after taping the erector spinae muscle. The paired t-test was performed to analyze changes in chest compression quality after taping. As results, taping enhanced back muscle strength and positively affected the depth of chest compressions and the compression to recoil ratio. Taping also increased confidence and lowered fatigability during chest compressions, so the participants preferred being taped while performing chest compressions. Based on these results, taping could help emergency room medical personnel specialized in CPR to enhance the quality of CPR and relieve back pain and fatigability by strengthening the back muscles.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.497-502
• /
• 2001

We examined the silicate-based material to develop the surface-treatment agent, which would be used to restore performance of the deteriorated concrete and to inhibit corrosion of the reinforcing bar. As a part of the study, we carried out experiments of the penetration and strengthening properties of concrete treated by the considering agent. The variables of experiment, were the type of silicates, the ratio of distilled water-silicate, the usage of surface-strengthening material, and the usage of biochemical material. The penetrating ability of concrete is assessed by viscosity and surface tension. Also assessments of strengthening effects of concrete are performed on compressive strength, absorption, and water permeability tests.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1994년도 봄 학술발표회 논문집
• /
• pp.25-29
• /
• 1994

A series of 6 reinforced concrete beams was tested to verify the effects of EBSP strengthened on cracked beams and to identify the various parameters affecting structure strengthening design(SSD). The parameters were the cross-sectional area of steel plates, the thickness of steel plates, and bond length of steel plates. In addition to these parameters, the effect of existing cracks on the strengthening was investigated. Test results show that EBSP is very effective and predictable for strengthening damaged structures. The results also show that the bond length of steel plates is the most important factor to develop ultimate load carrying capacities of strengthened beams. However, considerations in SSD should be given to assure the ductile failure at ultimate load such as the low ratio of thickness to the width of plates.

• 한국구조물진단유지관리공학회 논문집
• /
• 제6권4호
• /
• pp.243-254
• /
• 2002

This study investigates the structural behavior of cracked or uncracked RC columns retrofitted with CFS and evaluates the shear retrofit performance through experiment. Experimental works were conducted for sixth specimens varied in the adhesion method of CFS, the ratio of shear reinforcement bar, and the existence of crack before retrofitting. Throughout cyclic test, the strength, stiffness, failure modes, and ductility are discussed. The test results show that the retrofitting method with CFS improve the shear strength and ductility. The crack width below 2mm, occurred before retrofitting, didn't reduce the shear strengthening effect.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.469-474
• /
• 2002

Recently fiber sheets are used for strengthening the damaged concrete structures due to its many advantages such as its durability, non-corrosive nature, low weight, ease of application, cost saving, control of crack propagation, strength to thickness ratio, high tensile strength, serviceability and aesthetic. However, the lack of analytical procedures for predicting the nominal moment capacity by the fiber sheet reinforcement leads to difficulties in the effective process of decisions of the factors in the strengthening procedure. In this work, flexural strengthening effects by fiber sheets bonded on soffit and web of the member are theoretically studied for the reinforced concrete T beam. The analytical solutions are compared with experimental results of several references to verify the proposed approach.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.68-71
• /
• 2004

In the shear strengthening with FRP sheets, beams are wrapped around the webs and tension face of critical shear span by fiber sheets. The shear strength of RC beam strengthened with FRP sheets must be calculated based on the effective strain that can be developed in the FRP sheets at ultimate stage because the final failure modes of beams are governed by premature debonding of FRP sheet due to the limitation of bonded length by beam depth. An experimental study is carried out to evaluate the shear strengthening effect of AFRP or GFRP sheets with respect to shear reinforcement ratio of rebar. From the test results, it was found that the additional shear strength provided by GFRP or AFRP can be estimated by $p_w{\cdot}f_w$ based on the maximum effective strain of FRP sheet $4,000m{\mu}$ proposed by ACI 440 committee.

• Structural Engineering and Mechanics
• /
• 제66권4호
• /
• pp.543-555
• /
• 2018

Fiber Reinforced Polymer (FRP), which has a high strength to weight ratio, are now regularly used for strengthening of deficient reinforced concrete (RC) structures. While various researches have been conducted on FRP strengthening, an area that still requires attention is predicting the debonding failure load of prestressed FRP strengthened RC beams. Application of prestressing increases the capacity and reduces the premature failure of the beams largely, though not entirely. Few analytical methods are available to predict the failure loads under flexure failure. With this paucity, this research proposes a method for predicting debonding failure induced by intermediate crack (IC) for prestressed FRP-strengthened beams. The method consists of a numerical study on beams retrofitted with prestressed FRP in the tension side of the beam. The method applies modified Branson moment-curvature analysis together with the global energy balance approach in combination with fracture mechanics criteria to predict failure load for complicated IC-induced failure. The numerically simulated results were compared with published experimental data and the average of theoretical to experimental debonding failure load is found to be 0.93 with a standard deviation of 0.09.