• Journal of the Semiconductor & Display Technology
• /
• v.6 no.4
• /
• pp.65-68
• /
• 2007

An epitaxial NiSi structure on Si (001) substrate was studied by using density functional theory (DFT). Orhorhombic and B2-NiSi structures were compared first. B2 structure was further considered as it has same crystal structure as Si and the lattice mismatch between B2 and Si is small, compared to orthorhombic-NiSi. The lattice parameters of x- and y-direction in B2-NiSi structure were modified to match with those in Si (001). The size reduction of the lattice parameter of B2-NiSi to match with that of Si increased the lattice parameter of z-direction by 10.5%. Therefore, we propose that an optimum structure of NiSi for epitaxial growth on Si (001) is a tetragonal structure.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.3
• /
• pp.332-337
• /
• 2008

We analyzed carbonization pattern and crystal structure of polyvinyl chloride wire by thermal stress. Copper that is oxidized at normal temperature is a reddish brown. If under the thermal stress range of 500 to 700 [$^{\circ}C$], carbonization and exfoliation occurrence. Section structure of electric wire is same as arrangement of particle in metallograph analysis. But, as thermal stress increases, size of particle is enlarged. Electric wire displays elongation structure in SEM image analysis and elongation structure collapses when receive thermal stress at 300 [$^{\circ}C$]. In EDX analysis, we get the spectra of CuL, CuK, OK, and ClK. FT-IR analysis was shown new spectra with in range of $1,440{\sim}1,430\;[cm^{-1}]$, 1,340 [$cm^{-1}$], 1,240 [$cm^{-1}$].

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.1152-1155
• /
• 2007

Lately concerns about structure have been increased by advantages of floor impact noise, poilitical induction and changeability. Hence, Flat Plate Structure has been constructed increasingly. This study shows the comparison of the performance of sound insulation of Flat Plate Structure System and the existing Wall Structure. For this study, taking the same level organization of Daelim Architectural Environmental Research Center, I found the performance of sound insulation between the upper and lower floors about Wall Structure and Flat Plate Structure. Consequently, the performance of sound insulation between upper and lower floors of Flat Plate Structure was 3-5dB higher was approximately 3-5dB higher than one of Wall Structure. Especially, the performance of sound insulation on the upper floor was 1-3dB higher than on the lower floor. In addition, as the result of comparing radiation sound which radiates from the wall of lower floors with each structure system, Flat Plate Structure was about 4dB higher with Rw than Wall Structure. As we see totally, the performance of sound insulation of Flat Plate Structure is highter than one of the Wall Structure. It is 3-5dB higher and the main reason for this result depends on the existence of the wall which can radiate sound and nonexistence.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.1
• /
• pp.1-9
• /
• 2014

In this paper, a reconfigurable polarization patch antenna that uses a Y-shaped feed is proposed. The proposed antenna consists of a square patch, a Y-shaped feeding structure, a PIN diode, and a bias circuit for diode operation. The structural symmetry/asymmetry of the feeding structure is determined by the on/off operation of the PIN diode that inserted into the side of one of the lines of the Y-shaped feeding structure. For the proposed reconfigurable antenna, the two microstrip lines of the feeding structure have the same length when the PIN diode operates in the on state, and the antenna exhibits linear polarization(LP). On the other hand, when the PIN diode operates in the off state, the length of one side line of the feeding structure is relatively shorter than that of the other line. Therefore, the antenna exhibits circular polarization(CP). From the measurement results, it is found that the proposed antenna exhibits good impedance matching and axial ratio. In addition, polarization switching can be easily achieved in the same operating band.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.11
• /
• pp.2267-2272
• /
• 2009

The six-port direct conversion receiver front-end that is comprised of a carrier recovery and a phase shifter, which gets the same structure with six-port phase correlator using the multi-layer coupled line, was designed and fabricated in this paper. The six-port element that is comprised of the power divider and the hybrid coupler is designed by multi-layer coupled line structure. The multi-coupled structure is utilized as the basic structure in receiver phase correlator, carrier recovery circuit and phase shifter. The receiver front-end with the same multi-layer coupled line structure for the receiver elements shows the simple structure and no difficulty in integration. The fabricated multi-layer coupled six-port receiver front-end re-generates the carrier signal with a constant phase and demodulates the PSK transmission signal.

• Journal of Korea Society of Industrial Information Systems
• /
• v.15 no.2
• /
• pp.1-9
• /
• 2010

Feistel and SPN are the two main structures in a block cipher. Feistel is a symmetric structure which has the same structure in encryption and decryption, but SPN is not a symmetric structure. In this paper, we propose a SPN which has a symmetric structure in encryption and decryption. The whole operations of proposed algorithm are composed of the even numbers of N rounds where the first half of them, 1 to N/2 round, applies a right function and the last half of them, (N+1)/2 to N round, employs an inverse function. And a symmetry layer is located in between the right function layer and the inverse function layer. In this paper, AES encryption and decryption function are selected for the right function and the inverse function, respectively. The symmetric layer is composed with simple matrix and round key addition. Due to the simplicity of the symmetric SPN structure in hardware implementation, the proposed modified AES is believed to construct a safe and efficient cipher in Smart Card and RFID environments where electronic chips are built in.

• Structural Engineering and Mechanics
• /
• v.67 no.5
• /
• pp.481-492
• /
• 2018

The current experimental study is the reinforcement of the simple curvature vault masonry structures. In this study, we discuss complex structure include vault and rib cover with two radii and actual dimensions under a vertical load. The unreinforced structure data were compared with analysis data. The analysis data are in good agreement with experimental data. In the first experiment, a structure without reinforcement is tested and according to the test results, the second structure was reinforced using the carbon polymer fibers and the same test is done to see the effects of reinforcement. Based on the test results of the first structure, the first cracks are created in the vault. Moreover, the reinforcement with carbon fibers will increase the loading capacity of the structure around 35%.

• Structural Engineering and Mechanics
• /
• v.4 no.3
• /
• pp.209-226
• /
• 1996

One of the major divisions in the mathematical modelling of a tubular structure is to include the effect of the transverse shear stress and rotary inertia in vibration of members. During the past three decades, problems of vibration of tubular structures have been considered by some authors, and special attention has been devoted to the Timoshenko theory. There have been considerable efforts, also, to apply the method of spectral analysis to vibration of a structure with rectangular section beams. The purpose of this paper is to compare the results of the spectrally formulated finite element analyses for the Timoshenko theory with those derived from the conventional finite element method for a tubular structure. The spectrally formulated finite element starts at the same starting point as the conventional finite element formulation. However, it works in the frequency domain. Using a computer program, the proposed formulation has been extended to derive the dynamic response of a tubular structure under an impact load.

• Communications of the Korean Mathematical Society
• /
• v.37 no.1
• /
• pp.229-257
• /
• 2022

Let M be a semi-invariant submanifold of codimension 3 with almost contact metric structure (𝜙, 𝜉, 𝜂, g) in a complex space form M_n+1(c), c ≠ 0. We denote by A and R_𝜉 the shape operator in the direction of distinguished normal vector field and the structure Jacobi operator with respect to the structure vector 𝜉, respectively. Suppose that the third fundamental form t satisfies dt(X, Y) = 2𝜃g(𝜙X, Y) for a scalar 𝜃(< 2c) and any vector fields X and Y on M. In this paper, we prove that if it satisfies R_𝜉A = AR_𝜉 and at the same time ∇_𝜉R_𝜉 = 0 on M, then M is a Hopf hypersurface of type (A) provided that the scalar curvature s of M holds s - 2(n - 1)c ≤ 0.

• The Journal of the Korea Contents Association
• /
• v.20 no.3
• /
• pp.41-48
• /
• 2020

The purpose of this study is testing measurement invariance of the school vitality scale across the level of school. For this study, 3,156 elementary school teachers and 4,411 secondary school teachers were surveyed. As a result, school vitality scale was found to have the same factor structure in the structure regression model. Second, the factor load of the measurement model was found to be the same. Third, the structural path coefficients were the same. Fourth, structural covariance was found to be the same. Fifth, the structural residuals were the same. Based on these findings, it can be concluded that we can use school vitality scale both elementary school and secondary school. This study will contribute to diagnosing school vitality levels and finding ways to improve school management.