• Nuclear Engineering and Technology
• /
• v.55 no.6
• /
• pp.2335-2347
• /
• 2023

As medical facilities are usually built at urban areas, special concrete aggregates and evaluation methods are needed to optimize the design of concrete walls by balancing density, thickness, material composition, cost, and other factors. Carbon treatment rooms require a high radiation shielding requirement, as the neutron yield from carbon therapy is much higher than the neutron yield of protons. In this case study, the maximum carbon energy is 430 MeV/u and the maximum current is 0.27 nA from a hybrid particle therapy system. Hospital or facility construction should consider this requirement to design a special heavy concrete. In this work, magnetite is adopted as the major aggregate. Density is determined mainly by the major aggregate content of magnetite, and a heavy concrete test block was constructed for structural tests. The compressive strength is 35.7 MPa. The density ranges from 3.65 g/cm³ to 4.14 g/cm³, and the iron mass content ranges from 53.78% to 60.38% from the 12 cored sample measurements. It was found that there is a linear relationship between density and iron content, and mixing impurities should be the major reason leading to the nonuniform element and density distribution. The effect of this nonuniformity on radiation shielding properties for a carbon treatment room is investigated by three groups of Monte Carlo simulations. Higher density dominates to reduce shielding thickness. However, a higher content of high-Z elements will weaken the shielding strength, especially at a lower dose rate threshold and vice versa. The weakened side effect of a high iron content on the shielding property is obvious at 2.5 µSv=h. Therefore, we should not blindly pursue high Z content in engineering. If the thickness is constrained to 2 m, then the density can be reduced to 3.3 g/cm³, which will save cost by reducing the magnetite composition with 50.44% iron content. If a higher density of 3.9 g/cm³ with 57.65% iron content is selected for construction, then the thickness of the wall can be reduced to 174.2 cm, which will save space for equipment installation.

• Korean Journal of Environmental Agriculture
• /
• v.24 no.2
• /
• pp.106-116
• /
• 2005

This experiment was conducted to investigate available extraction capacity and potential mobility of heavy metal according to the distribution property and contamination level of heavy metals in soils and to suggest a reform measure of soil environment assessment methodology applied with soil quality and the official soil heavy metal test methods in domestic and foreign countries. The soils were collected from the natural forest paddy with long-term application of same type fertilizer, and paddies near metal mine and industrial complex. The post-treatment methods of soil were partial extraction, acid digestion and sequential extraction methods. For the heavy metal contents with different soil properties, it was shown that their natural forest and paddy soil were slightly low and similar to the general paddy soil, while their paddies near metal mine and industrial complex were higher than the standard level of Soil Environment Protection Act. Heavy metal concentrations in the soils with different soil properties had difference between $HNO_3\;and\;HNO_3+HCl$ extractant by US-EPA 3051a method. There were highly significant positive relationships in both two methods. It was appeared that the higher extractable concentration ratio with 0.1N-HCl to total heavy metal content with $HNO_3+HCl$ extractant the greater total heavy metal content. There were highly significant positive correlationship between total heavy metal content and extractable content with 0.1N-HCl. For extractable capacity of soil extractable solution compared to the total heavy metal content it was appeared that it extractable method with 0.1N-HCl was higher than those with EDTA and DTPA. In extractable ratio with 0.1N-HCl in the contaminated paddy soils near mine and industrial complex, it was shown that the lower soil pH, the higher total heavy metal content. The order of a potential mobility coefficient by distribution of heavy metal content with ie different typies in the soil was Cd>Ni>Zn>Cu>Pb. It could be known that contamination characteristics of heavy metals with different types of soils were affected by different heavy metal components, contamination degree and soil chemical properties, and heavy metal concentration with different extractable methods had great variations with adjacent environment. To be compared with assessment methodology of soil environment impact at domestic and foreign countries with our results, it might be considered that there was necessary to make a single analysis method based on total heavy metal content with environmental overloading concept because of various analysis methods for total heavy metal content and present analysis method with great variation according to soil environment. In spite of showing higher concentration of heavy metal with acidic digestion than the extractable method, it might be considered that there is need to be adjusted the national standard of soil heavy metal contamination.

• The Journal of Korean Academy of Prosthodontics
• /
• v.49 no.4
• /
• pp.324-332
• /
• 2011

Purpose: The purpose of this study was to compare the stress distribution of teeth and jaw on load by differentiating property of materials according to each layer of widely used mouthguard. Materials and methods: A Korean adult having normal cranium and mandible was selected to examine. A customized mouthguard was constructed by use of DRUFOMAT plate and DRUFOMAT-TE/-SQ of Dreve Co. according to Signature Mouthguard system. The cranium was scanned by means of computed tomography with 1mm interval. It was modeled with CANTIBio BIONIX/Body Builder program and simulated and interpreted using Alter HyperMesh program. The mouthguard was classified as follows according to the layers. (1) soft guard (Bioplast)(SG) (2) hard guard (Duran)(HG) (3) medium guard (Drufomat)(MG) (4) soft layer + hard layer (SG + HG) (5) hard layer + soft layer (HG + SG) (6) soft layer + hard layer + soft layer (SG + HG + SG) (7) hard layer + soft layer + hard layer (HG + SG + HG) The impact locations on mandible were gnathion, the center of inferior border, and the anterior edge of gonial angle. And the impact directions were oblique ($45^{\circ}$). The impact load was 800 N for 0.1 sec. The stress distribution was measured at maxillary teeth, TMJ and maxilla. The statistics were conducted using Repeated ANOVA and in case of difference, Duncan test was used as post analysis. Results: In teeth and maxilla, the mouthguard contacting soft layer of mandibular teeth presented lowest stress measure and, in contrast, in condyle, the mouthguard contacting hard layer of mandibular teeth presented lowest stress measure. Conclusion: For all impact directions, soft layer + hard layer + soft layer, the mouthguard with three layers which the hard layer is sandwiched between two soft layers, showed relatively even distribution of stress in impact.

• Food Science and Preservation
• /
• v.21 no.2
• /
• pp.187-192
• /
• 2014

This study was conducted to develop a salad dressing using jujube (Zizyphus jujuba Miller) puree and to evaluate the processing and quality characteristics of the salad dressing containing various amounts (0, 10, 20, 30, 40, and 50%) of jujube puree. Jujube puree was prepared by crushing peeled, deseeded and steamed fruit flesh. The dressing ingredients (jujube flesh puree, soy sauce, vinegar, oligosaccharide, olive oil, and water) were mixed, homogenized, and packaged in glass bottles. The quality characteristics (color property, total titratable acidity, soluble solids, viscosity, phenolic compound content, antioxidant activity, and sensory acceptability) of the dressing were analyzed. The lightness ($L^*$) and redness ($a^*$) of the dressing tended to increase as the amount of the jujube puree increased whereas the hue angle ($h^{\circ}$) decreased. The total titratable acidity, soluble solids, viscosity, phenolic compound content, and antioxidant activity of the dressing increased with the addition of more jujube puree. The sensory acceptability (color, smell, taste, texture, and overall acceptability) were significantly higher in the dressing added with 30% added jujube puree than in the other samples. The results show that jujube flesh puree (approximately 30%) can be utilized as an additive for preparing a dressing with simultaneously high antioxidant activity and acceptability.

• Journal of the Korean Wood Science and Technology
• /
• v.12 no.2
• /
• pp.20-26
• /
• 1984

This study was carried out to investigate the influence of chemical type and its retention in the fire-retardant treated plywoods on the static bending strength, a property peculiar to plywood. Being soaked in 20% aqueous solution of $(NH_4)_2SO_4$, $NH_4H_2PO_4$, $(NH_4)_2HPO_4$. Borax-Boric acid and Minalith for 3 to 12 hours at three-hour intervals and redried at $120^{\circ}C$ in hot press, the treated plywoods were put to static bending test. The values of chemical treated plywoods in Stress at proportional limit, Modulus of elasticity, Modulus of rupture and Work per unit volume to proportional limit were widely higher than those of water treated plywoods(control) and Borax-Boric acid treatment showed the highest value in the four mechanical data. And the bending strength of fire-retardant treated plywoods increased with the extension of soaking time or the increase of chemical retention in themselves. Borix-Boric acid was the desirable fire-retardant for thin plywood in view of mechanical strength and soaking defects in this study.

• Korean Chemical Engineering Research
• /
• v.51 no.5
• /
• pp.609-614
• /
• 2013

This study investigated the spontaneous combustion behavior of solvent-treated low rank coals. Indonesian lignite (a KBB and SM coal) and sub-bituminous (a Roto coal) were mixed with non-polar 1-methyl naphthalene (1MN) either by mechanical agitation or ultrasonication. The property change associated with 1MN treatment was then analyzed using proximate analysis, calorific value analysis, Fourier transform infrared (FT-IR), X-ray photoelectron spectroscopy and moisture re-adsorption test. Susceptibility to spontaneous combustion was evaluated using crossingpoint temperature (CPT) measurement along with gas analysis by GC. A FT-IR profile showed that oxygen functional groups and C-H bonding became weaker when treated by 1 MN. XPS results also indicated a decrease of the oxygen groups (C-O-, C=O and COO-). Increased hydrophobicity was found in the 1MN treated coals during moisture readsorption test. A CPT of the treated coals was ${\sim}20^{\circ}C$ higher than that of the corresponding raw coals and the ultrasonication was more effective way to enhance the stability against spontaneous combustion than the agitation. In the gas analysis less CO and $CO_2$ were emitted from 1MN treated coals, also indicating inhibition of pyrophoric behavior. The surface functional groups participating in the oxidation reaction seemed to be removed by the ultrasonication more effectively than by the simple mechanical agitation.

• Korean journal of food and cookery science
• /
• v.30 no.6
• /
• pp.670-678
• /
• 2014

The purpose of this study was to find the optimal swelling method and condition for seacucumber to improve its taste and texture to accomodate the rapid increase of consumption. Another purpose was to try to determine an easy way to soak dried sea-cucumber under different conditions, and identify the influence of swelling time on the texture of sea-cucumber, in order to reduce preparation time and provide basic data for easy handling. After boiling or steaming for six different periods including 5, 15, 30 and 60 minutes the texture of the sea-cucumbers were compared, For the additive test, the sea-cucumbers were boiling for 30 minutes period with 4 different additives and the textures were compared, Since the texture is an important characteristic of sea-cucumber, there are many variables that affect this property including the, drying and preservation methods. This study provides basic understanding of the influence of the heating method, time and temperature on the swelling of sea-cucumber for handy use at processing sites.

• Journal of Korea Foresty Energy
• /
• v.19 no.2
• /
• pp.93-101
• /
• 2000

Wood of Robinia pseudoacacia and bark of Populus alba$\times$P. glandulosa, Fraxinus rhynchophylla and Ulmus davidiana var. japonica were collected and extracted with acetone-water(7:3, v/v) in glass jar to examine whether its bioactive compounds exist. The concentrated extracts were fractionated with hexane, chloroform, ethylacetate and water, and then freeze-dried for column chromatography and bioactive tests. The isolated compounds were sakuranetin-5-O-$\beta$-D-glucopyranoside from Populus alba $\times$Pl glandulosa, 4--ethyoxy-(+)-leucorobinetinidin frm R. pseudoacacia and fraxetion from F. rhynchophylla and were characterized by $^1H$ and$^{13}C $ NMR and positive FAB-MS. Decay-resistant activity was expressed by weight loss ratio and hyphae growth inhibition in the wood dust agar medium inoculated wood rot fungi. R. pseudoacacia showed best anti-decaying property in both test and its methanol untreated samples, indicating higher activity than methanol treated samples in hyphae grwoth test. In antioxidative test, $\alpha$-tocopherol, one of natural antioxidants, and BHT, one of synthetic antioxidants, were used as references to cmpare with the antioxidant activities of the extacted fractions. Ethylacetate fraction of F. rhynchophylla bark indicated the hightest activity in this test and all fractions of R. pseudiacacia extractives also indicated higher activities compared with the other fractions. In the isolated compounds, aesculetin isolated from F. rhynchophylla bark showed best activity and followed by robonetinidin from R. pseudoacaica.

• Journal of Korean Society of Forest Science
• /
• v.101 no.3
• /
• pp.405-411
• /
• 2012

This study was conducted to evaluate short-term effects on soil properties and leaf characteristics after various treatments of soil amendments (organic fertilizer: 20 kg tree-1; compound fertilizer+wood-char: compound fertilizer 4 kg tree-1+wood-char 2 kg tree-1; lime fertilizer: 3 kg tree-1; mixed fertilizer: compound fertilizer 1 kg tree-1+organic fertilizer 10 kg tree-1+wood-char 1 kg tree-1; control) in chestnut (Castanea crenata S. et Z.) orchards of Jinju and Sancheong, Gyeongsangnam-do. Soil bulk density, soil pH, soil organic carbon, total nitrogen, exchangeable Ca2+ and Mg2+ in chestnut orchards were not significantly affected by soil amendment treatments. However, leaf weight was significantly higher in the lime fertilizer ($0.65\;g\;leaf^{-1}$) in Jinju and the organic fertilizer ($0.68\;g\;leaf^{-1}$) in Sancheong than in the control treatments (Jinju: $0.46\;g\;leaf^{-1}$; Sancheong: $0.53\;g\;leaf^{-1}$). Leaf area was also significantly higher in the lime fertilizer ($79.1\;cm^2\;leaf^{-1}$) in Jinju and the soil amendments ($70.4\;cm^2\;leaf^{-1}{\sim}78.2\;cm^2\;leaf^{-1}$) in Sancheong than in the control treatments (Jinju: $56.2\;cm^2\;leaf^{-1}$; Sancheong: $60.5\;cm^2\;leaf^{-1}$). Nitrogen concentration of leaf increased significantly in the mixed fertilizer (2.51%) and the compound fertilizer+wood-char (2.50%) compared with the control (1.98%) treatments. The results suggest that soil properties were not affected by soil amendment treatments during short-term period, but leaf characteristics and nitrogen concentration can be an indicator of soil nutrient improvements in chestnut orchards.

• Food Science and Preservation
• /
• v.24 no.8
• /
• pp.1138-1148
• /
• 2017

In this study, contetnts of phenolic acid and isoflavone, and biological activities of soy sauce were compared the soy sauce added bitter melon powder (BMPs). After the fermentation, pHs were decreased from 5.83 (0% BMP), 5.47 (5% BMP), and 5.32 (10% BMP) to 5.28, 5.36, and 5.16 at 90 days, whereas the acidities of soy sauce were increased from 0.06%, 0.07%, and 0.09% to 0.30%, 0.28%, and 0.36% at 90 days, respectively. In addition, the salinities of soy sauce were decreased, while viable cell numbers including Bacillus and yeast were increased. The contents of total phenolic, isoflavone-aglycone, and phenolic acid and antioxidant and ${\alpha}$-glucosidase inhibition activities were significantly increased for 90 days, while the isoflavone-glycoside contents were decreased. In Particular, soy sauce with 10% BMP at 90 days showed the highest contents of glutamic acid (GA, 9,876.09 mg/100 mL) and ${\gamma}$-aminobutyric acid (GABA, 325.02 mg/100 mL) contents than among other samples. Additionally, the radical scavenging activities (DPPH, ABTS, ${\cdot}OH$, and FRAP) and ${\alpha}$-glucosidase inhibition activities of soy sauce with 10% BMP at 90 days were shown to be high 96.07%, 97.27%, 59.47%, 1.98%, and 79.96%, respectively.