• Clean Technology
• /
• v.27 no.4
• /
• pp.359-366
• /
• 2021

Halloysite nanotubes (HNTs), the multiwalled clay mineral with the composition of Al₂Si₂O₅(OH)₄·nH₂O, have been highlighted as a low-cost adsorbent for the removal of dyes from wastewater. Although a powder of halloysite presents a high specific surface area, forming media are significantly considered due to sludge-clogging induced by the water-bound agglomeration. However, higher firing temperature to achieve the structural durability of the media and lower utilization rate due to longer penetration depth into the media act as hurdles to increase the dye-adsorption capacity. In this work, the retention of the adsorption capacity of halloysite was evaluated with methylene blue solution after the heat treatment at 750 ℃. In order to improve the utilization rate, tubular media were fabricated by extrusion. The images taken by transmission electron microscopy show that HNTs present excellent structural stability under heat treatment. The HNTs also provide superb capacity retention for MB adsorption (93%, 18.5 mg g^-1), while the diatomite and Magnesol^® XL show 22% (7.65 mg g^-1) and 6% (11.7 mg g^-1), respectively. Additionally, compositing with lignin enhances adsorption capacity, and the heat treatment under the hydrogen atmosphere accelerates the adsorption in the early stage. Compared to the rod-type, the tubular halloysite media rapidly increases methylene blue adsorption capacity.

• Resources Recycling
• /
• v.31 no.4
• /
• pp.56-65
• /
• 2022

Copper is one of the non-ferrous metals used in the electrical/electronic manufacturing industries due to its superior properties particularly the high conductivity and less resistivity. The effluent generated from the surface finishing process of these industries contains higher copper content which gets discharged in to water bodies directly or indirectly. This causes severe environmental pollution and also results in loss of an important valuable metal. To overcome this issue, continuous R & D activities are going on across the globe in adsorption area with the purpose of finding an efficient, low cost and ecofriendly adsorbent. In view of the above, present investigation was made to compare the performance of a plant root (Datura root powder) as a bio-adsorbent to that of the synthetic one (Tulsion T-42) for copper adsorption from such effluent. Experiments were carried out in batch studies to optimize parameters such as adsorbent dose, contact time, pH, feed concentration, etc. Results of the batch experiments indicate that 0.2 g of Datura root powder and 0.1 g of Tulsion T-42 showed 95% copper adsorption from an initial feed/solution of 100 ppm Cu at pH 4 in contact time of 15 and 30 min, respectively. Adsorption data for both the adsorbents were fitted well to the Freundlich isotherm. Experimental results were also validated with the kinetic model, which showed that the adsorption of copper followed pseudo-second order rate expression for the both adsorbents. Overall result demonstrates that the bio-adsorbent tested has a potential applicability for metal recovery from the waste solutions/effluents of metal finishing units. In view of the requirements of commercial viability and minimal environmental damage there from, Datura root powder being an effective material for metal uptake, may prove to be a feasible adsorbent for copper recovery after the necessary scale-up studies.

• Clean Technology
• /
• v.24 no.1
• /
• pp.55-62
• /
• 2018

The adsorbent used in water-adsorption cooling system utilizing low-temperature heat of below $90^{\circ}C$ is required to exhibit high water uptake capacity at a relative humidity ($P/P_0$) between 0.1 and 0.3. Mesoporous silica (MCM-41) and MOF(MIL-101) exhibit quite large water adsorption capacity under saturated water vapor at $35^{\circ}C$. However, these adsorbents show small water adsorption capacity ($0.027{g_{water}\;g_{ads}}^{-1}$, $0.074{g_{water}\;g_{ads}}^{-1}$, respectively) in the relative humidity ($P/P_0$) range of 0.1 to 0.3. In this study, the surface properties of mesoporous silica and MOF were modified by simple methods to develop an adsorbent having a higher water uptake than the conventional water adsorbents at a relative humidity ($P/P_0$) of 0.1 ~ 0.3. In the case of mesoporous silica (MCM-41) exhibiting mainly water adsorption at $P/P_0=0.5{\sim}0.7$, aluminum species was functionalized on the mesopore walls and then cations existing near the aluminum were exchanged with various cations (e.g., $Na^+$, ${NH_4}^+$, and $(C_2H_5)_4N^+$). In addition, 20 wt% (to total weight of the composites) of hygroscopic inorganic salt ($CaCl_2$) was impregnated on the MCM-41. In the case of the MIL-101 (MOF), 20 wt% of hygroscopic inorganic salt ($CaCl_2$) was impregnated on the MIL-101. The MCM-41 which was ion-exchanged with various cations has main adsorption branch around 0.5 of $P/P_0$ which was slightly shifted with low-pressure direction in comparison with pristine MCM-41. However, tiny increases were observed on the adsorption in the range of $P/P_0$ between 0.1 and 0.3. After salt impregnation on the MCM-41, the adsorption capacity under $P/P_0=0.1{\sim}0.3$ at $35^{\circ}C$ was increased from $0.027{g_{water}\;g_{ads}}^{-1}$ to $0.152{g_{water}\;g_{ads}}^{-1}$. In the case of MIL-101, the amount of water adsorption at $35^{\circ}C$ under $P/P_0=0.1{\sim}0.3$ was increased from $0.074{g_{water}\;g_{ads}}^{-1}$ to $0.330{g_{water}\;g_{ads}}^{-1}$ after the salt impregnation.

• Economic and Environmental Geology
• /
• v.55 no.4
• /
• pp.407-419
• /
• 2022

Soil(vadose zone) gas compositions were measured for about 3 days to suggest a method for monitoring and interpreting soil gas data collected around wells from which methane(CH₄) is outflowing. The vadose zone gas samples were collected within 1 m around two test wells(TB2 and TB3) at Pohang and analyzed for CO₂, CH₄, N₂ and O₂ concentrations in situ. CO₂ flux was measured beside TB2. In addition, gas samples from well head in TB2 and atmospheric air samples were collected for comparison. Carbon isotopes of CO₂(δ¹³C_CO2) of samples collected on the last day of the study period were analyzed in the laboratory. The two test wells (TB2 and 3) were 12.7 m apart and only TB3 was cemented to the surface. According to the bio-geochemical process-based interpretation, the relationships between CO₂ and O₂, N₂, and N₂/O₂ of vadose zone gas were plotted between the lines of CH₄ oxidation and CO₂ dissolution. In addition, the CH₄ concentrations of gas samples from the wellhead of the uncemented well (TB2) were 5.2 times higher than the atmospheric CH₄ concentration. High CO₂ concentrations (average 1.148%) of vadose zone gas around TB2 seemed to be attributed to the oxidation of CH₄. On the other hand, the vadose zone CO₂ around the cemented well(TB3) showed a relatively low concentration(0.136%). This difference indicates that the vadose zone gas(including CO₂) around the CH₄ outflowing well were strongly affected by well completion(cementing). This study result can be used to establish strategies for environmental monitoring of soil around natural gas sites, and can be used to monitor leakage around injection and observation wells for CO₂ geological storage. In addition, the method of this study is useful for soil monitoring in natural gas storage and oil-contaminated sites.

• Journal of the Korean Institute of Gas
• /
• v.22 no.5
• /
• pp.53-61
• /
• 2018

Low-salinity water based polymerflooding (LSPF) is one of promising enhanced oil recovery (EOR) method that has the synergetic effect of combining polymer injection method and low-salinity water injection method. In order to maximize EOR efficiency, it is essential to design low-salinity water appropriately considering the properties of polymer. In this aspect, the main purpose of this study is to investigate the effect of pH and $SO_4{^{2-}}$ ion which one of PDI (Potential Determining Ion) on oil production when applying LSPF to carbonate oil reservoir. First, the stability and adsorption of polymer molecule were analyzed in different pH of injection water and $SO_4{^{2-}}$ concentration in injection water. As a result, regardless of pH and $SO_4{^{2-}}$ concentration, when $SO_4{^{2-}}$ ion was contained in injection water, the stability of polymer solution was obtained. However, from the result of polymer retention analysis, in neutral state of injection water, since $SO_4{^{2-}}$ interfered the adsorption of polymer, the adsorption thickness of polymer was thinner as $SO_4{^{2-}}$ concentration was higher. On the other hand, when injection water was acidic as pH 4, the amount of polymer adsorption increased with the injection of polymer solution, so the mobility of polymer solution was greatly lowered. From the results of wettability alteration due to low-salinity water effect, in the case of neutral injection water injected, as $SO_4{^{2-}}$ concentration was increased, more oil which attached on rock surface was detached, altering wettability from oil-wet to water-wet. On the other hand, in acidic condition, due to complex effect of rock dissolution and polymer adsorption, wettability of the entire core system was less altered relatively to neutral condition. Therefore, it was evaluated that better EOR efficiency was obtained when injecting low-salinity water based polymer solution containing high concentration of $SO_4{^{2-}}$ with neutral condition, enhancing the oil production up to 12.3% compared to low-salinity water injection method.

• The Korean Journal of Food And Nutrition
• /
• v.15 no.4
• /
• pp.321-325
• /
• 2002

For examination, amaranth was first dried its surface after sufficient soaking in water. Dried amaranth was roasted when the moisture contents reached 30∼50%, its nasty smell disappeared and its color turned to yellow and it was puffed. Pretreated amaranth was added to biscuit for the improvement of apparence and merchandise value. The maximum expansion was reported at the moisture percentage of 130∼160% according to the examination of expansion and moisture percentage. In order to compare gelatinization of different processing, three different amaranth were prepared as follows ; Raw amaranth, steamed/dried amaranth, and roasted amaranth. The degree of gelatinization was increased as the percentage of moisture was increased and the degree of gelatinization of roasted amaranth was higher than the one of steamed/dried amaranth, their moisture contents were 62.10% and 57.59%, respectively In addition, the hardness($\times$10$\^$5/dyn/㎠) of roasted amaranth was showed lower values than that of steamed amaranth and raw amaranth were showed the large values. After examining biscuits containing each amaranth, raw amaranth had problem with nasty smell and bad texture, and streamed/dried amaranth were able to remove viscosity but turned brown. Biscuits containing roasted amaranth had good smell and texture, and besides the color of biscuits became bright because roasted amaranth turned white. Biscuits tasted best when it contained 5% of roasted amaranth. The rancidity of biscuits with 5% roasted amaranth were proceeded slowly while roasted amaranth itself had high acid value and peroxide value. For the safety from oxidation, it was fairly safe for about 6 months.

• Journal of Korea Water Resources Association
• /
• v.56 no.12
• /
• pp.919-928
• /
• 2023

Rainfall characteristics in Korea are concentrated during the summer flood season. In particular, when a large amount of turbid water flows into the dam due to the increasing trend of concentrated rainfall due to abnormal rainfall and abnormal weather conditions, prolonged turbid water phenomenon occurs due to the overturning phenomenon. Much research is being conducted on turbid water prediction to solve these problems. To predict turbid water, turbid water data from the upstream inflow is required, but spatial and temporal data resolution is currently insufficient. To improve temporal resolution, the development of the Turbidity-SS conversion equation is necessary, and to improve spatial resolution, multi-item water quality measurement instrument (YSI), Laser In-Situ Scattering and Transmissometry (LISST), and hyperspectral sensors are needed. Sensor-based measurement can improve the spatial resolution of turbid water by measuring line and surface unit data. In addition, in the case of LISST-200X, it is possible to collect data on particle size, etc., so it can be used in the Turbidity-SS conversion equation for fraction (Clay: Silt: Sand). In addition, among recent remote sensing methods, the spatial distribution of turbid water can be presented when using UAVs with higher spatial and temporal resolutions than other payloads and hyperspectral sensors with high spectral and radiometric resolutions. Therefore, in this study, the Turbidity-SS conversion equation was calculated according to the fraction through laboratory analysis using LISST-200X and YSI-EXO, and sensor-based field measurements including UAV (Matrice 600) and hyperspectral sensor (microHSI 410 SHARK) were used. Through this, the spatial distribution of turbidity and suspended sediment concentration, and the turbidity calculated using the Turbidity-SS conversion equation based on the measured suspended sediment concentration, was presented. Through this, we attempted to review the applicability of the Turbidity-SS conversion equation and understand the current status of turbid water occurrence.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.37 no.10
• /
• pp.1294-1300
• /
• 2008

Nelumbo nucifera G. tea white breads were prepared by the addition of 0.01, 0.02, 0.03, and 0.04% hemicellulase to flour of the basic formulation. The experiments and control were then compared in terms of quality characteristics, including pH, total titratable acidity, fermentation power of dough expansion, specific volume, baking loss, moisture content, color, textural characteristics, external and internal surface appearances, and sensory qualities in order to determine the optimal ratio of hemicellulase in the formulation. There were no significant differences in pH and total titratable acidity of dough among the experiments. Fermentation power of dough expansion were increased as incubation time increased. Baking loss was the highest at the 0.04% addition level, while the lowest at the 0.01% level. As hemicellulase content increased, pH, hardness, and fracturability of bread decreased, while total titratable acidity, specific volume, and resilience increased. Water content and lightness were the highest in the control bread samples, and yellowness was maximal in the 0.01% group. Bread made by the addition of hemicellulase had significantly higher greenness and flavor than the control group. Color, consistency, and springiness of crumb, density and uniformity of crumb pore, softness, chewiness, overall acceptability, lotus leaf flavor, delicious taste, astringency, bitterness, and off-flavor were not significantly different among the samples. The results indicate that adding 0.02$\sim$ 0.03% hemicellulase in N elumbo nucifera G. tea white bread is optimal for quality and provides a product with reasonably high overall acceptability.

• Korean Chemical Engineering Research
• /
• v.47 no.6
• /
• pp.762-767
• /
• 2009

In this study, the feasibility of using vegetable oil extracted from tropical crop seed as a biodiesel feedstock was investigated by producing biodiesel and analysing the quality parameters as a transport fuel. In order to produce biodiesel efficiently, two step reaction process(pre-treatment and transesterificaion) was required because the tropical crop oil have a high content of free fatty acids. To determine the suitable acid catalyst for the pre-esterification, three kinds of acid catalysts were tested and sulfuric acid was identified as the best catalyst. After constructing the experimental matrix based on RSM and analysing the statistical data, the optimal pre-treatment conditions were determined to be 26.7% of methanol and 0.982% of sulfuric acid. Trans-esterification experiments of the pre-esterified oil based on RSM were carried out, then discovered 1.24% of KOH catalyst and 22.76% of methanol as the optimal trans-esterification conditions. However, the quantity of KOH was higher than the previously established KOH concentration of our team. So, we carried out supplemental experiment to determine the quantity of catalyst and methanol. As a result, the optimal transesterification conditions were determined to be 0.8% of KOH and 16.13% of methanol. After trans-esterification of tropical crop oil, the produced biodiesel could meet the major quality standard specifications; 100.8% of FAME, 0.45 mgKOH/g of acid value, 0.00% of water, 0.04% of total glycerol, $4.041mm^2/s$ of kinematic viscosity(at $40^{\circ}C$).

• Tuberculosis and Respiratory Diseases
• /
• v.41 no.5
• /
• pp.484-488
• /
• 1994

Background : The antigen-specific receptor on the surface of most peripheral T lymphocytes is a disulfide-linked heterodimer composed of $\alpha$ and $\gamma$ subunits, noncovalently associated with CD3 polypeptides. Recently, a novel type of CD3-associated heterodimer was described on a T cell subset that does not express CD4 or CD8 molecules. This second type of TCR dimer is composed of chains encoded for by the $\gamma$- and $\delta$-TCR genes. These cells may exert both cytotoxic and lymphokine producing functions. Although it was reported that some ${\gamma}{\delta}$-TCR might recognize an MHC-linked determinant, the funεtion or physiologic ligand for this new receptor is not yet clear. It was found that ${\gamma}{\delta}$-TCR can react with 65 kD heat shock protein of M. tuberculosis, which suggests the possible protective role of ${\gamma}{\delta}$ T lymphocytes against tuberculosis. In our previous study, there was neither the increase in number nor the functional activation of ${\gamma}{\delta}$ T cells in the peripheral blood from patients with pulmonary tuberculosis. Now we report the distribution of ${\gamma}{\delta}$ T cells in the regional sites of M. tuberculosis infection, especial1y tuberculous lymphadenitis. Methods : Lymph nodes from patients with pathologically-proven tuberculous lymphadenopathy (n=5) and reactive hyperplasia (n=3) were used. Tissues were frozen in liquid nitrogen immediately after removal and stored below $-70^{\circ}C$. The cryostat sections of these frozen specimens were stained with anti-Leu-4 Ab, Identi-T TCR ${\delta}1$, and Identi-T ${\beta}F1$. The number of positively stained cells were counted at high power field. Results : The infiltration of ${\gamma}{\delta}$ T cells was significantly higher in the lymph nodes from patients with tuberculous lymphadenopathy than that with reactive hyperplasia ($16.3{\pm}10.3%$ vs. $1.7{\pm}1.5%$). Conclusion : These results suggest that ${\gamma}{\delta}$) T cells may play a role in the defense against M. tuberculosis infection, especially in the regional sites of infection.