• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 춘계 학술논문 발표대회
• /
• pp.96-97
• /
• 2014

The purpose of this study is to analyze the adhesion strength of metal spray coating system in steel using high-frequency arc metal spray method. For the purpose the experimental factor such as surface roughness was selected at 3 levels. As a result of experiment, it appeared that high-frequency arc metal spray method had higher adhesion strength than existing metal spray method. Especially, Al-Mg showed the highest adhesion strength than other metals. In case of surface roughness, the higher roughness steel has, the higher adhesion strength appeared.

• 한국환경과학회지
• /
• 제10권3호
• /
• pp.179-185
• /
• 2001

To investigate daily variations of water mass distribution in the west and the east parts of Jeju Island, we implemented observations from June 20 to 22, 1997. (The results are as follows : Temperatures in the east and the west were similar in the surface, but $15.02^{\circ}C$ and $13.8^{\circ}C$ in the bottom, respectively.) In the east and west, the surface and the deep salinities are 33.81, 33.34 and 34.33, 34.11 respectively. The east shows higher temperature and salinity than the west. The distributions of nitrate in the east and the west were very similar in the surface regions.(In the deep regions, however, the east shows higher than the west.) The east shows higher phosphates than the west both in surface and deep regions. The silicate had similar distributions to nitrate. Chlorophyll-a of the west was twice higher than that of the east. The daily variations of temperature and salinity were largest at 30m depth, and pH was not much changed in the depth and the pH in day was higher than that at night. The variations of nutrients were much changed in the depth, and nitrate and phosphate at night were higher than those in day. Daily variations of silicate, however, was not much changed in the observation times. Ratio of N/P in the east and the west were 13 and 16, respectively, so that the west was higher than the east. However the ratios were two times higher both in the east and the west in day, when planktons are more active than at night. Si/P ratio showed little different between day and night and between surface and deep regions. The correlation of nitrogen and phosphorus was high (plus relation), and the correlation of AOU, nitrogen and phosphorus was high(plus relation) in the east, however, not high in the west.

• 한국지형학회지
• /
• 제27권4호
• /
• pp.13-28
• /
• 2020

In this study, the distribution and topographic development of marine terraces, UHS (Upper Higher Surface) and HHS (High Higher Surface) at Yeondae-san area, Gampo-eup were discussed. We critically examined on the substance of the Yeongdong-myeon (a low-lying erosion surface) in the east coast of Korea. In study area, UHS including UHS-246m, UHS-241m, UHS-235m, UHS-220m, UHS-210m and UHS-220 is found on the highest altitude among the marine terraces in Korea. The existence of UHS requires new interpretation on topographical surface like Yeongdong-myeon, which has been commonly accepted as a theory in the society of Korean Geography. Since UHS is distributed continuously ascending on the altitude of HHS, the period of formation should be understood in the same context. And UHS of paleo-shoreline 246m has been estimated to be formed about 1.5 million years ago.

• 한국세라믹학회지
• /
• 제49권4호
• /
• pp.328-332
• /
• 2012

Etch rates of Si and high purity SiC have been compared for various fluorocarbon plasmas. The relative plasma resistance of SiC, which is defined as the etch rate ratio of Si to SiC, varied between 1.4 and 4.1, showing generally higher plasma resistance of SiC. High resolution X-ray photoelectron analysis revealed that etched SiC has a surface carbon content higher than that of etched Si, resulting in a thicker fluorocarbon polymer layer on the SiC surface. The plasma resistance of SiC was correlated with this thick fluorocarbon polymer layer, which reduced the reaction probability of fluorine-containing species in the plasma with silicon from the SiC substrate. The remnant carbon after the removal of Si as volatile etch products augments the surface carbon, and seems to be the origin of the higher plasma resistance of SiC.

• 보존과학연구
• /
• 통권20호
• /
• pp.21-47
• /
• 1999

According to damage of papers by the chemical cause, papers become to acidify. Among the 3 kinds of method measuring the acidity of paper, one was nondestructive method measuring the surface of the paper by flat type electrode and the others were destructive methods measuring directly by cold water extract method and hot water extract method. In case of the cellulolytic cultural properties, the latter methods were not applied because those methods must bedissociated papers. To measure the paper acidity nondestructively, we investigated the correlation of the nondestructive method and the destructive methods. The conclusions are as follows. 1) In the relationship of the cold water extract method and the hot water extract method, It was indicated that the pH measured by the hot water extract method was high quality printing paper 0.08, rough printing paper 0.13, and Korean paper 0.29 higher than that by the cold water extract method.2) In the relationship of the cold water extract method and the surface measurement method, It showed that the pH value measured by the cold water extract method was high quality printing paper 1.86, rough printing paper 0.80,and Korean paper 0.58 higher than value that by the surface measurement.3) In the relationship of the hot water extract method and the surface measurement method, It showed that the pH value measured by the hot ABSTRACT water extract method was high quality printing paper 1.78, rough printing paper 0.66, and Korean paper 0.29 higher than that by the surface measurement. From the above-mentioned results, the pH value measured by the surface measurement was need to high about 1.78∼1.86 in high quality printing paper, 0.66-0.80 in rough printing paper, and 0.29∼0.58 in Korean paper and the surface measurement with flat type electrode was very available to measure the acidity of Korean papers actually.

• 보존과학연구
• /
• 통권20호
• /
• pp.49-64
• /
• 1999

According to damage of papers by the chemical cause, papers become to acidify. Among the 3 kinds of method measuring the acidity of paper, one was nondestructive method measuring the surface of the paper by flat type electrode and the others were destructive methods measuring directly by cold water extract method and hot water extract method. In case of the cellulolytic cultural properties, the latter methods were not applied because those methods must bedissociated papers. To measure the paper acidity nondestructively, we investigated the correlation of the nondestructive method and the destructive methods. The conclusions are as follows. 1) In the relationship of the cold water extract method and the hot water extract method, It was indicated that the pH measured by the hot water extract method was high quality printing paper 0.08, rough printing paper 0.13, and Korean paper 0.29 higher than that by the cold water extract method.2) In the relationship of the cold water extract method and the surface measurement method, It showed that the pH value measured by the cold water extract method was high quality printing paper 1.86, rough printing paper 0.80,and Korean paper 0.58 higher than value that by the surface measurement.3) In the relationship of the hot water extract method and the surface measurement method, It showed that the pH value measured by the hot ABSTRACT water extract method was high quality printing paper 1.78, rough printing paper 0.66, and Korean paper 0.29 higher than that by the surface measurement. From the above-mentioned results, the pH value measured by the surface measurement was need to high about 1.78∼1.86 in high quality printing paper, 0.66-0.80 in rough printing paper, and 0.29∼0.58 in Korean paper and the surface measurement with flat type electrode was very available to measure the acidity of Korean papers actually.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.141-141
• /
• 2013

Shape control of metal nanocrystals has broad applications, including catalysis, plasmonics, and sensing. It was found that controlling the atomic arrangement on metal nanocrystal surfaces affects many properties, including the electronic dipole or work function. Tuning the surface structure of exposed facets of metal nanocrystals was enabled by shape control. We investigated the effect of shape on nanomechanical properties, including friction and adhesion forces. Two nanoparticles systems, high-index {321} and low-index {100}, were used as model nanoparticle surfaces. Scanning force microscopy was used to probe nanoscale friction and adhesion. Because of the abundant presence of high-density atomic steps and kinks, high-index faceted nanoparticles have a higher surface energy than low-index faceted cubic nanoparticles. Due to this high surface energy, high-index faceted particles have shown stronger adhesion and higher friction than low-index nanoparticles. We discuss the results in light of the differences in surface energy as well as the effect of capping layers in the measurement.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.251-254
• /
• 2002

The technique of high speed machining is widely studied in machining field. In this study, TiAIN single-layered and TiAIN/TiN double-layered coatings were applied to end-mill by an arc ion plating technique. Their performances were comparatively studied about cutting force, tool wear, tool life and surface roughness of workpiece under high speed cutting conditions. The TiAIN single-layer coated tool showed higher wear-resistance due to its higher hardness, while the TiAIN/TiN double-layer coated tool showed better performance for high metal removal, i.e., high fled per tooth condition due to its higher toughness. The surface roughness of the workpiece was not influenced by the wear amount of coated tools.

• 한국자동차공학회논문집
• /
• 제24권3호
• /
• pp.285-293
• /
• 2016

The high velocity oxygen fuel(HVOF) thermal spray is a kind of surface modification techniques to produce the sprayed coating layer. This process is to form the coating layer after spraying the powder to molten or semi-molten state by the ultra-high speed at the high-temperature heat source and conflicting with a substrate. The efficiency of thermal spraying is dropped, however, because the semi-molten powder in a spray process become a factor that degrades the mechanical property by the formed pore within the coating layer. Therefore, it is necessary to melt completely the thermal spray powder in order to produce the coating layer with an optimal adhesive force. In this study, to improve the wear resistance, corrosion resistance and heat resistance, the plungers of high-speed and ultra-high pressure reciprocating hydraulic pumps used in ironworks are manufactured with STS $420J_2$ and are coated by the powders of WC-Co-Cr and WC-Cr-Ni including the WC of high hardness using a HVOF thermal sprayer developed in this laboratory. These are called by the surface-modified plungers. The surface roughness, hardness, and surface and cross-sectional microstructure of these two surface-modified and conventional ceramic plungers are measured and compared before operation with after operation for 100 days. It is found that the values of centerline average surface roughness and maximum height for conventional ceramic plunger are 9.5 to 10.8 and 5.2 to 5.7 times higher than those of surface-modified ones coated by WC-Co-Cr and WC-Cr-Ni because the fine tops and bottoms on surface roughness curve of conventional ceramic plunger are approximately 100 times higher than those of surface-modified ones. In addition, the pores and scratches in the surface microstructure are considerably formed in the order of conventional ceramic, WC-Cr-Ni and WC-Co-Cr surface-modified plungers. The greater the WC content of high hardness powder is less the change in the plunger surface.

• 열처리공학회지
• /
• 제7권4호
• /
• pp.318-327
• /
• 1994

According to conventional nitriding of tool steels, it was very difficult to produce a high surface hardness. This study has been conducted to investigate the influence of initial structures on the nitriding characteristics of tool steels in gas-nitrided for the improvement in surface hardness. The specimens (SACM645, STD61 steels) have been quenching and tempering at various temperature and then gas-nitrided for 30, 45 and 60hr at 500, 530 and $550^{\circ}C$ respectively in gasatmosphere of 30%$NH_3-70%N_2$ As hardness of initial structure was higher, the nitriding layer was deeper and hardness of the nitriding layer was higher. Deeper nitriding layers was due to higher diffusion rate by fine initial microstructure. Also the reason of high surface hardness was associated with formation of dispersed fine carbonitrides of nitrides.