• Title/Summary/Keyword: tensile strength and elongation

Search Result 1,256, Processing Time 0.031 seconds

Effect of Cold Working on the Tensile Properties of Fe-20Mn-12Cr-3Ni-3Si Alloy (Fe-20Mn-12Cr-3Ni-3Si 합금의 인장성질에 미치는 냉간가공의 영향)

  • Jung, Jong-Min;Kim, Kwon-Hoo
    • Journal of the Korean Society for Heat Treatment
    • /
    • v.34 no.3
    • /
    • pp.116-121
    • /
    • 2021
  • This study was carried out to investigate the effect of transformation induced martensite on the tensile properties of Fe-20Mn-12Cr-3Ni-3Si alloy. α' and ε-martensite were formed by cold rolling, and these martensite were formed with according to the specific direction, surface relief and partially intersection. With an increasing degree of cold rolling, amount of α'-martensite was slowly increased, whereas amount of ε-martensite was rapidly increased. Volume fraction of ε-martensite formed by cold working was large than α'-martensite. Tensile strength was rapidly increase and elongation was rapidly decreased with an increasing of degree of cold rolling. This means that tensile strengh and elongation was greatly influenced by the volume fraction of ε-martensite formed by cold rolling then α'-martensite.

Effects of Stability and Volume Fraction of Retained Austenite on the Tensile Properties for Q&P and AM Steels (Q&P와 AM강의 잔류오스테나이트 분율과 안정도에 따른 인장특성 거동)

  • Byun, Sang-Ho;Oh, Chang-Suk;Nam, Dae-Geun;Kim, Young-Seok;Kang, Nam-Hyun;Cho, Kyung-Mox
    • Korean Journal of Materials Research
    • /
    • v.19 no.6
    • /
    • pp.305-312
    • /
    • 2009
  • The effects of Quenching and Partitioning (Q&P) and Annealed Martensite (AM) heat treatment on the microstructure and tensile properties were investigated for 0.24C-0.5Si-1.5Mn-1Al steels. The Q&P steels were annealed at a single phase ($\gamma$) or a dual phase (${\gamma}+{\alpha}$), followed by quenching to a temperature between $M_s$ and $M_f$. Then, enriching carbon was conducted to stabilize the austenite through the partitioning, followed by water quenching. The AM steels were intercritically annealed at a dual phase (${\gamma}+{\alpha}$) temperature and austempered at $M_s$ and $M_s{\pm}50^{\circ}C$, followed by cooling in oil quenching. The dual phase Q&P steels showed lower tensile strength and yieldyield strength than those of the single phase Q&P steels, and tThe elongation for the dual phase Q&P steel was partitioning 100s higher than that of that for the single phase Q&P steels as the partitioning time was less than 100s up to partitioning 100s. For AM steels, the tensile/yield strength decreased and the total elongation increased as the austempering temperature increased. The stability of the retained austenite controlled the elongation for Q&P steels and the volume fraction of the retained austenite controlled the elongation for AM steels.

Effects of the Ordering Reaction on High Temperature Mechanical Behavior in Alloy 600 (Alloy 600에서 고온 기계적 거동에 미치는 규칙 반응의 영향)

  • Kim, Sung Soo;Kim, Dae Whan;Kim, Young Suk
    • Korean Journal of Metals and Materials
    • /
    • v.50 no.10
    • /
    • pp.703-710
    • /
    • 2012
  • The effects of the ordering reaction on high temperature mechanical behavior is investigated by tensile tests at $2{\times}10^{-2}/s-3.3{\times}10^{-5}/s$ up to $745^{\circ}C$. The tensile deformed region is examined by differential scanning calorimeter (DSC), TEM, and high resolution neutron diffraction (HRPD). The results showed that a plateau of tensile strength appeared at $150-500^{\circ}C$ whereas the elongation minimum occurred at about $600^{\circ}C$. This suggests that the occurrence of a plateau does not cause the elongation minimum. The temperature of the elongation minimum decreases with the strain rate. HRPD results show a lattice contraction in the tensile deformed specimen at the temperature of the plateau occurring region. The plateau of tensile strength, the lattice contraction, and the occurrence of serration appeared in the same temperature region.

Tensile Behavior Characteristics of CANDU Pressure Tube Material Degraded by Neutron Irradiations (중수로 압력관 재료의 조사 열화에 따른 인장거동 특성)

  • An, Sang-Bok;Kim, Yeong-Seok;Kim, Jeong-Gyu
    • Transactions of the Korean Society of Mechanical Engineers A
    • /
    • v.26 no.1
    • /
    • pp.188-195
    • /
    • 2002
  • To investigate the degradation of mechanical properties induced mainly by neutron irradiation, the tensile tests were conducted from room temperature to 300\\`c using the irradiated and the unirradiated Zr-2.5Nb pressure tube materials. The irradiated longitudinal and transverse specimens were collected from the coolant inlet, middle, and outlet parts of M-11 tube which had been operated in Wolsung CANDU Unit-1 and exposed to different operating temperatures and irradiation fluences. The different tensile behavior was characterized not by the fluences of irradiation but by the tensile loading direction. The transverse specimen showed the higher strength and lower elongation than those of the longitudinal one. It was believed that these phenomena resulted from the microstructure anisotropy caused by the extrusion process. The increased strength hardening and decreased elongation embrittlement of the irradiated material were compard to those of the unirradiated one. While the tensile strength of the inlet was higher than that of the outlet, the elongation of the inlet was lower than that of outlet. Considering the operation condition, it was proposed that the operating temperature could be a more effective parameter than the irradiation fluence for long-time life. Through the TEM observation, it was found that while the a-type dislocation density was increased, the c-type dislocation was not changed in the irradiated. The fact that the higher dislocation density was sequentially distributed over the inlet, the middle, and the outlet parts was consistent with the distribution of the tensile strength.

Effect of Alloying Elements on Particulate Dispersion Behavior and Mechanical Properties in TiC Particulate Reinforced Magnesium Matrix Composites (TiC 입자강화 Mg 복합재료에 있어서 입자 분산거동 및 기계적 성질에 미치는 합금원소의 영향)

  • Lim, Suk-Won;Choh, Takao;Park, Yong-Jin
    • Journal of Korea Foundry Society
    • /
    • v.14 no.3
    • /
    • pp.240-247
    • /
    • 1994
  • TiC particulate reinforced magnesium matrix composites were fabricated by melt stirring method. The effect of alloying elements on TiC particulate dispersion into molten magnesium and mechanical properties were investigated. The incorporation time is defined as the time required for dispersion of solid particles into molten metal. The incorporation time of TiC particles into molten pure magnesium was remarkably shorter and the particulated dispersion was more uniform than that of pure aluminum which was reported previously. The incorporation time was, prolonged by the addition of Al, Bi, Ca, Ce, Pb, Sn or Zn. The tensile strength increased and elongation decreased by the addition of Cu or Sn into the matrices and composites. Although, the tensile strength of the matrices and composites increased by alloying with Ca or Ce, the maximum elongation was observed at a content of about 1% for the matrices. By alloying with Zn, the tensile strength increased for the matrices and composites, but the elongation of the matrices increased. The pure magnesium and its alloy matrix composites reinforced with 20vol% TiC have the tensile strength of about 400MPa. This value is compared with the tensile strength of SiC whisker reinforced magnesium matrix composites fabricated by liquid infiltration method at the same volume fraction. There fore, the melt strirring method which has the advantages of simple process is considered to be efficient in fabricating magnesium matrix composites.

  • PDF

A Study on the Development of Traditional Korean Paper Changphanji by the Bast Fiber of Paper Mulberry (닥나무의 인피섬유(靭皮纖維)를 이용(利用)한 전통(傳統) 한지장판지(韓紙壯版紙) 개발(開發)에 관(關)한 연구(硏究))

  • Cheon, Cheol
    • Journal of the Korean Wood Science and Technology
    • /
    • v.18 no.4
    • /
    • pp.53-64
    • /
    • 1990
  • This study was carried out to develop the traditional korean paper changphanji from the bast fiber of paper mulberry The results obtained were as follows: 1. The variations in the basis weight were remarkable, but there were no significant adverse effects on the tensile strength and thickness. 2. The stamping have contributed to the improvement of smoothness and the control of thickness. The automatic pressing system recommended to obtain good control of thickness. 3. The average density of the traditional korean paper changphanji was 1.06g/$cm^3$. 4. The changphanji developed in this study gave a clude, but excellent toughness and warm feeling. Some fiber lumps, dark spots and bamboo, screen marks were also obserded. 5. The tensile strength of four-fold sheet changphanji is highest and those of two-fold sheet changphanji is lowest. the lengthwise tensile strength was higher than crosswise one due to the fiber. 6. The elongation of three-fold sheet changphanji was highest 7. The water absorption of all products ranged from 11.3g/$m^2$ to 17.5g/$m^2$. 8. The wight loss by abrasion was 34.0%(four-fold sheet) 31.6%(three fold sheet), 31.0% (two-fold sheet)respectively. 9. Based on the results obtained. tensile strength and elongation, the four-fold sheet was excellent. the use of the bast fiber of paper mulberry as a raw material is attractive point which can not obtained from the commercial changphanji made from other raw materials.

  • PDF

HIP Diffusion Bonding of Two Types of Superalloys for Engine Blisk Applications (엔진 블리스크 제조를 위한 초내열합금 이종재의 HIP Diffusion Bonding)

  • 나영상;황형철;염종택;권영삼;박노광
    • Transactions of Materials Processing
    • /
    • v.12 no.1
    • /
    • pp.60-65
    • /
    • 2003
  • HIP diffusion bonding of Ni-based superalloys, cast Mar-M247 (MM247) and Udimet 720 (U720) powder, was experimentally and numerically studied. Subsolvus HIP treatment was optimized by investigating the variations of high temperature tensile properties of HIP-bonded specimens with powder size, HIP'ing time, etc. While the tensile strength at high temperatures showed no detectable changes, the tensile elongation and reduction in area were slightly increased as the powder size decreased from -140 mesh to -270 mesh. While as-HIP'ed U720 showed a high tensile strength comparable to that of lorded U720 alloy, the HIP diffusion-bonded specimen showed a strength lower than the forged U720 alloy and the cast MM247 alloy The increase of HIP'ing tune from 2 hours to 3 hours resulted in a rapid risc of tensile strength and elongation due to the disappearence of microvoids in the cast MM247. FEM simulation for HIP process was conducted by applying the McMeeking micromechanical model, which uses power-law creep model as constitutive equations. ABAQUS user subroutine CREEP with an implemented microscopic model was used for the simulation. Numerical simulation was shown to be essential for the near-net shape manufacturing as well as the HIP process optimization.

Microstructural Evolution and Tensile Properties of Cu-Sn Based Alloys Manufactured by Spray Casting Route (분무주조에 의해 제조된 Cu-Sn계 합금의 미세조직 및 인장성질)

  • Shim, Sang-Hyun;Kang, Hee-Soo;Baik, Kyeong-Ho
    • Journal of Powder Materials
    • /
    • v.17 no.6
    • /
    • pp.477-481
    • /
    • 2010
  • Cu-Sn based alloys were manufactured by gas atomization spray casting route in order to achieve a fine scale microstructure and a high tensile strength. The spray cast Cu-10Sn-2Ni-0.2Si alloy had an equiaxed grain microstructure, with no formation of brittle ${\delta}-Cu_{41}Sn_{11}$ phase. Aging treatment promoted the precipitation of finely distributed particles corresponding to ${\delta}-Ni_2Si$ intermetallic phase throughout the $\alpha$-(CuSn) matrix. The cold-rolled Cu-Sn-Ni-Si alloy had a very high tensile strength of 1200 MPa and an elongation of 5%. Subsequent aging treatment at $450^{\circ}C$ for 1h slightly reduced the tensile strength to 700 MPa and remarkably increased the elongation up to 30%. This result has been explained by coarsening the precipitates due to over aging and reducing the dislocation density due to annealing effects.

Production and Properties of Edible Film Using Whey Protein

  • Chae, Seung-Il;Heo, Tae-Ryoen
    • Biotechnology and Bioprocess Engineering:BBE
    • /
    • v.2 no.2
    • /
    • pp.122-125
    • /
    • 1997
  • The utilization of excess whey is necessary to reduce dairy waste because the large amount of whey disposal in waste streams has caused environmental problems. During whey protein film production as the effective means of utilization of excess whey, we have examined the effects of pH, temperature, and plasticizers for water vapor permeability(WVP), tensile strength(TS), and elongation rate(%E) of the whey protein films. The 10% whey protein films had the highest WVP(28.73g$.$mm/kPa$.$day$.$㎡) and TS(1.85${\pm}$0.11Mpa). But, in this case, an increase of WVP was caused by the thickness of whey protein films. At the concentration of 8% whey protein, appropriate thickness was obtained. Whey protein films prepared at the pH 6.75 and 95$^{\circ}C$ showed lower WVP(28.38g$.$mm/kPa$.$day$.$㎡) and elongation rate(12.9%) and higher TS value(3.769${\pm}$0.407 MPa) than at the pH 6.75 and 75$^{\circ}C$. As the temperature increased, WVP of films decreased slightly and tensile strength increased slightly, while elongation rate decreased significantly. Higher WVP and TS were observed at pH6.75 compared to pH7-9. In contrast, significantly higher elongation was observed at pH 9comapred to pH6.75-8. Among the plasticizer types used, the addition of sorbitol showed the highest TS value(6.244${\pm}$0.297 MPa) at the concentration 0.4g sorbitol and elongation rate(49%) at the concentration of 0.6g sorbitol.

  • PDF

Study on the Mechanical Properties of Rubber Composite Materials Contained PBO, Aramid Chopped Fiber (PBO, Aramid Chopped Fiber가 함유된 고무복합재료의 기계적 물성연구)

  • Lee, Jun Hee;Lee, Kwang-Woo
    • Textile Coloration and Finishing
    • /
    • v.33 no.4
    • /
    • pp.327-337
    • /
    • 2021
  • The uniformly dispersed Aramid and Poly (phenylene benzobisoxazole) (PBO) in a variety of rubber was investigated. The mechanical properties of rubber were characterized by hardness, tensile strength, elongation at break, heat resistance, oil resistance, cold resistance, ozone resistance measurements. The 3mm Aramid chopped fiber better tensile strength than the other Chopped fiber. The Aramid of 3mm chopped fiber showed excellent reinforcing in rubber composite because of homogeneous dispersion. Consequently, the best 3mm Aramid chopped fiber and rubber improved the tensile strength and elongation at break of the composite. Also, 3mm Aramid chopped fiber improved the oil-resistant, ozone resistant and cold resistant.