• Journal of the Korean Wood Science and Technology
• /
• v.20 no.1
• /
• pp.51-59
• /
• 1992

The acetylation of papermaking pulp fiber(SwBKP, SwUKP, HwBKP and HwBCTMF) is carried out to modify the characteristics of pulp and paper. The effects of the addition of acetylated pulp on the filler retention and paper properties were investigated. The acetylation depended upon pulp type and the content of short fiber and fines. The addition of acetylated SwBKP did not deteriorate the retention of clay, talc and calcium carbonate, while the retention of titanium dioxide was increased with the addition of 20% and above. The brightness opacity, air permeability and tear strength were improved, but water resistance, burst strength and folding endurance were decreased by the addition of acetylated SwBKP and SwUKP. The tensile strength of SwBKP was increased until 20% of acetylated pulp is added, and then decreased. The tensile strength of SwUKP, however, was not changed until the acetylated pulp of 25% is added. The dimensional stability was improved by the addition of acetylated pulp and showed the different response to SwBKP and SwUKP.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.3 s.174
• /
• pp.625-633
• /
• 2000

The mechanical and curing properties of short nylon66 fiber reinforced Chloroprene rubber have been investigated as functions of interphase conditions and fiber content. The tensile strength exhibits a dilution effect at a low fiber content in each interphase. It is found that the interphase conditions have an important affect on the dilution ratio and critical fiber content. Double coatings of bonding agent 402 and rubber solution become the best interphase model in this study. The yield strength, tensile modulus, tear strength and fracture toughness at rupture, Jr are significantly improved due to fiber concentration.

• Archives of Plastic Surgery
• /
• v.35 no.6
• /
• pp.659-662
• /
• 2008

Purpose: Silicone gel sheet(SGS) is used for preventing and treating keloid or hypertrophic scars. Because the product is weak in tear strength and adherence, it requires several replacements, which requires high cost. As a solution for this problem, we developed a new silicone gel sheet, named as Scar Clinic, and confirmed its physical properties. Methods: Tensile strength, elongation rate, adhesiveness, and water vapor transmission rate were experimentally compared between the most commonly used SGS product and the Scar Clinic. Results: The newly developed SGS showed better results compared to the existed SGS in regards to tensile strength, elongation rate, adhesiveness, and water vapor transmission rate. Conclusion: The Scar Clinic showed higher durability and flexibility. It will be a useful product for treating scars clinically.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.42 no.3
• /
• pp.50-57
• /
• 2010

A mill trial was performed in a kraft paper mill in order to evaluate the possibility of utilizing dual polymer dry strength aids system consisting of cationic PVAm and anionic PAM. It was found that the cationic PVAm - anionic PAM dry strength additives can improve paper strength without significantly disturbing the stability of the kraft papermaking process when virgin UKP was used as a furnish. Tensile strength (25.3% in machine direction, 48.4% in cross machine direction), elongation of paper (31.6%, 15.6%) and tensile energy absorption (48%, 54%) were improved. Air permeability of the kraft paper was improved as well (22%). Tear strength was decreased with PVAm dry strength aids system, but it can be compensated with decreasing refining degree. In addition, the mill trial results indicate that highly air permeable kraft sack paper can be produced by the addition of PVAm dry strength agents at the stock with reduced freeness.

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.1
• /
• pp.88-104
• /
• 1999

This study was carried out to classify the Hanjis into three groups that were indigenous Hanji, traditional Hanji, and improved Hanji handmade by paper making method according to the physical properties of each paper sheet such as tensile, bursting and tearing strength, folding endurance and fiber orientation in each layer. The results obtained were summarized as follows: 1. The multi-layered Hanjis made by "Oebal" Hanji making method in different direction of fiber orientation have good properties in tearing resistance. 2. The multi-layered Hanji in different direction of fiber orientation has good properties in the tearing resistance, but the burst index and the breaking length results were lower than the single layered Hanjis. 3. The different fiber orientation and multi-layered method didn't increase, the three indexes(burst index, tear index, breaking length). Only, the different direction of fiber orientation decreased the difference of width and length strength (tensile, tear) of the Hanji. 4. "Dochim"(Korean finishing touch process for indigenous Hanji by fulling round sticks) greatly increase folding endurance(double folds, not $log_{10}$) and good effect to tensile strength and burst strength. 5. The today's Oebal Hanji were the maximum of 2 layers and the indigenous Oebal Hanji were 16 layers the maximum. In addition, average of the indigenous Oebal Hanji was 4 layers(all 4-layer Hanji were the different fiber orientation of each layer). 6, The indigenous Hanji(multi-layered, and different fiber orientation) was good condition with "Dochim". Dochim increased tensile strength and burst strength of the indigenous Hanji. So the three-strength indexes were similar level("--"). 7. When the number of layer which were same fiber orientation increase, the increased Hanji became similar strength pattern("V", breaking length and burst index was higher than tear index) with "Ssangbal" Hanji. 8. The single layered papers that made by "Oebal" Hanji making method were similar strength pattern with Ssangbal Hanji. 9. There was no way to find the width and length direction of multi-layered Hanji by comparison between the difference of tensile strength and the difference of tearing resistance. 10. The compared pattern of tensile strength and tearing resistance of indigenous Oebal Hanji was different from today's Oebal Hanji. Especially, the tearing resistance of all indigenous Oebal Hanji(16 samples) was stronger on width of tearing resistance. And in the half of indigenous Oebal Hanji samples, the width of tensile strength and tearing resistance was stronger than length strength (Indigenous Oebal: '$\ulcorner\lrcorner$' 50%, '$\bigcup$' 50% $\leftrightarrow$ Today's Oebal: '$\ulcorner\lrcorner$' 12%, '$\bigcup$'6%, '$\llcorner\urcorner$'17%, '$\bigcap$'65%). In 65% today's Oebal, the length direction of tensile strength and tearing resistance was stronger than the width direction.

• Journal of Bio-Environment Control
• /
• v.5 no.1
• /
• pp.23-33
• /
• 1996

This study was performed to induce a quality improvement and standardization of materials used for greenhouse. For this purpose, physical and mechanical properties of agricultural films for greenhouse were measured by kinds and thickness of the films. The properties are composed of impact, tensile, tear propagation strength and light transmittance. The results were summarized as follows. 1. At the impact test result of the falling dart, the thicker the film, the greater the impact strength of soft film. The impact weight at 50 percents is from 158g to 213g and the strength of low density polyethylene(LDPE) film is higher than the rest of any other films. 2. Seeing the leveling of the impact rupture, maximum impact weight which was ruptured very little ranges from 62g to 192g. The impact strength of 0.1mm films was higher than that of 0.05mm as from 1.8 to 3.2 times. 3. Tensile weight covers from 0.95kg to 2.22kg in the test materials, and the weight of lengthwise film is larger than that of width. LDPE film has high value of tensile weight. Elongation range is from 345 to 102 percent and lengthwise elongation is greater than width as much as from 1.4 to 2.7 times. 4. Tea. propagation strength ranges from 80.5kg/cm to 121.7kg/cm, and unlike which of LDPE film has high value, EVA film has low value in the films tested. The width strength is higher than the lengthwise. 5. The light transmittance of the soft film is about 78-92 percent in the range of ultraviolet ray, but has high value in the visible ray range.

• Journal of Korean Association for Spatial Structures
• /
• v.11 no.3
• /
• pp.115-123
• /
• 2011

It is needed to investigate the material properties of ETFE foil under various temperatures because ETFE membrane foils have very thin depth and relatively high flexibility. In this paper, the material properties of ETFE membrane foil obtained from 3 testes under various temperatures are presented. First, the uniaxial test under four temperatures as -20$^{\circ}C$, 0$^{\circ}C$, +20$^{\circ}C$ and +40$^{\circ}C$ was performed. Each 5 specimen was tested and the yield stress, tensile strength and the Young's modulus of the foils are obtained. Second, the creep testes under three temperatures as 25$^{\circ}C$, 40$^{\circ}C$ and 60$^{\circ}C$, 3MP, 6MP and 9MP tension load was subjected to the specimen and the creep characteristics was investigated. Finally, the tear test under $5^{\circ}C$, $^0{\circ}C$ and $20^{\circ}C$ was performed. It is concluded that the shape of stress-strain curve or general behaviors are similar with that of normal temperatures but the mechanical characteristics of ETFE membrane foils were affected by the temperatures, obviously.

• Clinics in Shoulder and Elbow
• /
• v.18 no.3
• /
• pp.138-143
• /
• 2015

Background: To evaluate the effect of preoperative fatty degeneration of deltoid and teres minor muscles on the clinical outcome in patient with reverse total shoulder arthroplasty (RTSA). Methods: Nineteen patients with RTSA were enrolled. The mean follow-up period was 16.1 months. The fatty degeneration of three distinct parts in each deltoid and the teres minor muscle was measured using a preoperative magnetic resonance imaging. Postoperatively, the muscle strengths for forward elevation (FE), abduction (Abd), and external rotation (ER) were measured using a myometer at the last follow-up. The parameters for clinical outcome were Constant Score (CS) and Korean Shoulder Score (KSS). Results: The number of cases was 10 in group 1 and 9 in group 2. The strength of FE and Abd were significantly higher in group 1 (p<0.001 and p<0.001, respectively), and the strength of ER was not different significantly between two groups (p=0.065). For the clinical outcome, both CS and KSS were higher in group 1 (p=0.002 and p=0.002, respectively). The number of patients in group A was 11, and group B was 8. Although there was not a significant difference in terms of FE and Abd between group A and B (p=0.091, p=0.238), ER was significantly higher in group A (p=0.012). We did not find a significant difference in the clinical scores (CS, p=0.177 and KSS, p=0.238). Conclusions: These findings suggest the importance of a preoperative evaluation of the fatty degeneration of deltoid and teres minor muscles for predicting postoperative strength and clinical outcome.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.1
• /
• pp.10-18
• /
• 2000

To improve the physical properties of OCC (Old Corrugated Container) fibers, we used the mechanical pre-treatment on the fibers before refining . The mechanical action in the Hobart mixer induced high shear and compression on the fibers, which resulted in changes of fiber internal structure, and microcompressions on the surface of the fibers. We evaluated the amount of mechanical treatment on the fibers by fiber curl index for convenience. Four different refining techniques were applied to the pre-treated fibers (valley beater, Kady mill, PFI mill, and Impact refining) to find the best combination of the pre-treatment and the refining methods. Conclusions were summarized as followed. 1. Mechanical pre-treatment in Hobart mixer for more than 1 hour caused the increase of curl index of OCC fibers, and increased breaking length, burst index, and tear index the handsheets more than 10 % in this experiment. 2. Kady mill and PFI mill refining were effective in keeping fiber length from shortening Kady mill and Valley beater refining straightened out the fiber curls, and reduced the curl index. 3. Valley beating reduced fiber length very fast and generated fines more than other refining methods. 4. To increase breaking length and burst strength while keeping tear strength , combination of mechanical pre-treatment and Valley beating were most effective.

• Elastomers and Composites
• /
• v.46 no.3
• /
• pp.186-194
• /
• 2011

Natural fiber/natural rubber composites were fabricated by uniformly compounding natural rubber and cellulose- based natural fiber kenaf and then by compression molding. The effect of kenaf fiber content on their vulcanization behavior, hardness, tensile properties, tear strength and static and dynamic properties was investigated. The contents of kenaf fiber in the composites were 0, 5, 10, 15, and 20 phr, compared to natural rubber and additives. The result indicated that various properties of natural rubber depended on the kenaf fiber content. With increasing kenaf fiber content, the torque for vulcanization of natural rubber was increased whereas the vulcanization time was reduced as well. The hardness, tensile modulus and tear strength of kenaf/natural rubber composites were gradually decreased with the fiber content whereas the tensile strength and elongation at break were decreased. Also, with increasing the kenaf fiber content the dynamic property of natural rubber was changed more greatly than the static property. The loss factor, which is closely related with the damping or absorption of the energy given to natural rubber, was proportionally increased with the fiber content.