• 한국정밀공학회지
• /
• 제26권12호
• /
• pp.62-68
• /
• 2009

In this paper, we investigate a new method to measure the thickness of thin transparent objects utilizing a step index multi-mode optical fiber sensor. The method mainly depends on the refraction rate of transparent target, the diameter of optical fibers and the distance to reflector. We confirmed the effects of these parameters through the experimental verification tests. The comparison between the theoretical vs. analytical results shows good agreements with each other. The proposed model also enables users to measure the thickness of thin transparent objects without considering the reflection from the target. This approach provides simple, cost-effective and non-contact solutions to measure the thickness.

• Nuclear Engineering and Technology
• /
• 제43권1호
• /
• pp.13-18
• /
• 2011

In this study, simulations were done of a 661.6 keV line from a point source of $^{137}Cs$ housed in a lead shield. When increasing the scattering angle from 60 to 120 degrees with a 6061 aluminum alloy target placed at angles of 30 and 45 degrees to the incident beam, the spectra showed that the single scattering component increases and that the multiple scattering component decreases. The investigation of the single and multiple scattering components was carried out using a MCNP5 simulation code. The component of the single Compton scattering photons is proportional to the target electron density at the point where the scattering occurs. The single scattering peak increases according to the thickness of the target and saturates at a certain thickness. The signal-to-noise ratio was found to decrease according to the target thickness. The simulation was experimentally validated by measurements. These results will be used to determine the best conditions under which this method can be applied to testing electron densities or to assess the thickness of samples to locate defects in them.

• 한국방사선학회논문지
• /
• 제14권3호
• /
• pp.193-201
• /
• 2020

본 연구 목적은 선형가속기를 통해 입사된 전자가 표적(target)을 구성하는 물질과 두께에 따른 광자 특성을 평가하는 것이다. 전산모사 설계는 2 mm 두께의 텅스텐 단일물질과 1.8 mm 와 2.3 mm 두께의 텅스텐과 구리 복합물질로 구성된 선형가속기 표적(Target)이다. 연구 방법은 첫째, 표적 내 일차 입자의 거동은 전자플루언스와 전자 에너지 축적으로 평가하였다. 둘째, 표적 내에서 발생하는 광자는 광자 플루언스로 평가하였다. 셋째, 표적으로부터 1 m 거리에서의 광자 각-에너지 분포는 광자 플루언스로 평가하였다. 그 결과 첫째, 단일물질과 복합물질 표적에서의 전자 플루언스와 에너지 축적을 통해 일차 입자인 전자가 표적 밖으로 방출되지 않았으며, 표적 두께에 따라 전자가 음의 선형적으로 감쇄하였다. 둘째, 복합물질 표적이 단일물질 표적보다 광자 생성이 더 높은 것으로 나타났다. 이는 물질 구성 성분과 두께가 광자 생성에 영향을 준다는 사실을 확인하였다. 셋째, 차폐 해석에 필요한 각 분포에 따른 광자 플루언스를 계산하였다. 이러한 결과는 선형가속기 표적을 구성하는 물질과 두께에 따라 광자 생성률이 차이 나는 것을 확인할 수 있었다. 따라서, 본 연구는 국가에서 도입 중인 컨테이너 보안 검색용 선형가속기 사용시설의 설계 및 운영 시 필요한 자료이며, 방사선 방호에 기초 자료로 활용될 수 있을 것으로 생각된다.

• 대한조선학회논문집
• /
• 제45권5호
• /
• pp.562-568
• /
• 2008

In this study, the target FSICR class is 1A whose target thickness of the brash ice is 46 mm in model scale. Normally ice floes for brash ice do not exceed 2 m in full scale, so the model ice sheet was cut by about 10 cm by 10 cm using hand saws. Since the target thickness of brash ice is 46 mm, 46 mm ice sheet makes one layer brash ice. For 23 mm thickness ice sheet, two layers should be accumulated to reach 46mm brash ice thickness. For 15mm thickness ice sheet, three layers need to be accumulated as the same as those in 23 mm ice sheet. New methodology to produce a brash ice was proposed. The results showed that it would be important to use multi-layer rather than single layer possibly because of significant thrust deduction from the propeller-ice interaction in the present ice condition (FSICR 1A).

• 한국표면공학회지
• /
• 제33권5호
• /
• pp.349-355
• /
• 2000

Indium tin oxide (ITO) thin films have been deposited on PET (polyethylene terephthalate) and glass substrates by a do magnetron sputter method of powder target without heat treatments such as substrate heater and post heat treatment. During the sputtering deposition, sputtering parameters such as sputtering power, working pressure, oxygen gas mixture, film thickness and substrate-target distance are important factors for the high quality of ITO thin films. The structural, electrical and optical properties of as-deposited ITO oxide films are investigated by sputtering power, oxygen partial pressure and films thickness among the several sputtering conditions. XRD patterns of ITO films are affected by sputtering power and pressure. As the power and pressure are increased, (411) and (422) peaks of ITO films are grown strongly. Electrical resistivity is also increased, as the sputtering power and pressure are increased. Transmittance of ITO thin films in the visible light ranges is lowered with an increase of sputtering power and film thickness. Reflectance of ITO films in infra-red region is decreased, as the power and pressure is increased.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.116.3-116
• /
• 2001

A diagnosis methodology for thickness quality in hot finishing mill is proposed based on multivariate statistical analysis. The thickness of hot strip is a key quality factor that is measured by x-ray thickness gauge. Currently, the thickness quality is guaranteed by upper and lower limit of thickness deviation from target thickness. But if any over-limit is occurred, there is no in-line method to identify the causes. In this paper, many parameters are extracted from the thickness deviation signal such as mean deviation(top, middle, tail), rms deviation(top, middle, tail) and peak deviation(top, middle, tail) as time domain parameters ...

• Journal of the Korean Wood Science and Technology
• /
• 제29권3호
• /
• pp.47-58
• /
• 2001

For finding both ways of recycling the wood and plastic wastes and solving the problem of free formaldehyde gas emission through manufacturing wood particle-polypropylene fiber composite board without addition of formaldehyde-based thermosetting resin adhesive, control particleboards and nonwoven web composite boards from wood particle and polypropylene fiber formulation of 50 : 50, 60 : 40, and 70 : 30 were manufactured at density levels of 0.5, 0.6, 0.7, and 0.8 g/$cm^3$, and were tested both in the physical and mechanical properties according to ASTM D 1037-93. In the physical properties, control particleboard had significantly higher moisture content than composite board. In composite board, moisture content decreased with the increase of target density only in the board with higher content of polypropylene fiber and also appeared to increase with the increase of wood particle content at a given target density. Control particleboard showed significantly greater water absorption than composite board and its water absorption decreased with the increase of target density. In composite board, water absorption decreased with the increase of target density at a given formulation but increased with the increase of wood particle content at a given target density. After 2 and 24 hours immersion, control particleboard was significantly higher in thickness swelling than composite board and its thickness swelling increased with the increase of target density. In composite board, thickness swelling did not vary significantly with the target density at a given formulation but its thickness swelling increased as wood particle content increased at a given target density. Static bending MOR and MOE under dry and wet conditions increased with the increase of target density at a given formulation of wood particle and polypropylene fiber. Especially, the MOR and MOE under wet condition were considerably larger in composite board than in control particleboard. In general, composite board showed superior bending strength properties to control particleboard, And the composite board made from wood particle and polypropylene fiber formulation of 50 : 50 at target density of 0.8 g/$cm^3$ exhibited the greatest bending strength properties. Though problems in uniform mixing and strong binding of wood particle with polypropylene fiber are unavoidable due to their extremely different shape and polarity, wood particle-polypropylene fiber composite boards with higher performance, as a potential substitute for the commercial particleboards, could be made just by controlling processing variables.

• Journal of the Korean Wood Science and Technology
• /
• 제33권2호통권130호
• /
• pp.40-55
• /
• 2005

This study was carried out to discuss the feasibility of wood and plastic wastes as the raw materials for wood particle-plastic composites. For this purpose, composites were manufactured from coarse and fine wood particles and polypropylene fibers by nonwoven web process. And the effect of wood particle size on the performance of the composites were analyzed according to ASTM D 1037-93. In the physical properties of composites, water absorption decreased with the increase of target density and polypropylene fiber content. And the composites with fine wood particles appeared to have slightly lower water absorption than those with coarse wood particles. Thickness swelling did not vary significantly with the increase of target density but increased with the increase of wood particle content. And the composites with fine wood particles were significantly lower in thickness swelling than those with coarse wood particles. In the mechanical properties of composites, dry and wet MOR showed the increasing tendency with the increase of polypropylene fiber content and target density. Dry and wet MOE showed the increasing tendency with the increase of target density but only wet MOE exhibited the increasing tendency with the increase of polypropylene fiber content. Composites with fine wood particles appeared to be generally higher in wet MOR and MOE than those with coarse wood particles. In conclusion, composites with fine wood particles showed generally higher performance than those with coarse ones. Also, composites were significantly superior to control particleboards in the performance, especially in water absorption and thickness swelling.

• 한국표면공학회지
• /
• 제47권1호
• /
• pp.53-56
• /
• 2014

I-V characteristics of a cylindrical target in an ECR plasma were studied for sheath spatial evolutions when the target was pulsed biased to a high negative potential. The magnetic field effects on sheath thickness and sheath boundary speed were investigated by comparison between the experimental results and the theoretical results using the Child-Langmuir sheath model. The results showed that the magnetic field suppressed electron motion away from the target so that sheath thickness and sheath boundary speed decreased.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.365-366
• /
• 2007

High quality cathode with high deposition rate of thin films and long target life time is required for manufacturing TFT-LCD and semiconductor. We developed WV(wide view) sputtering cathode with wide erosion area and high deposition rate. Ti thin film thickness variation in WV cathode is below 5% for 380 kWh target life time. Al thin film thickness using normal cathode is decreased about 20%. By using WV cathode, target using efficiency was improved 40%. in comparison with normal cathode.