• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.239-244
• /
• 1999

Radial immersion ratio is an important factor to determine the threshold in face milling and should be estimated in process for automatic force regulation. In this paper, presented is a method of on-line estimation of radial immersion ratio using cutting force. When a tooth finishes sweeping, sudden drop of cutting forces occurs. These force drops are equal to the cutting forces that act on a single tooth at the swept angle of cut and can be acquired from cutting force signals in feed and cross-feed directions. The ratio of cutting forces in feed and cross-feed directions acting on the single tooth at the swept angle of cut is a function of the swept angle of cut and the ratio of radial to tangential cutting force. In the research, it is found that the ratio of radial to tangential cutting force is not affected by cutting conditions and axial rake angle. Therefore, the ratio of radial to tangential cutting force determined by just one preliminary experiment can be used regardless of the cutting conditions. Using the measured cutting forces and predetermined ratio, the redial immersion ratio is estimated. various experiments show that the radial immersion ratio can be estimated by the proposed method very well.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.82-88
• /
• 2002

A simple beam subjected to a uniformly distributed tangential follower force and the successive two moving spring-mass systems upon it constitute this vibration system. The influences of the velocities of the moving spring-mass system, the distance between the successive two moving spring-mass systems and the uniformly distributed tangential follower force have been studied on the dynamic behavior of a simple beam by numerical method. The uniformly distributed tangential follower force is considered within its critical value of a simple beam without the successive two moving spring-mass systems, and three kinds of constant velocities and constant distance of the successive two moving spring-mass systems are also chosen. Their coupling effects on the transverse vibration of the simple beam are inspected too.

• 한국대기환경학회지
• /
• 제16권2호
• /
• pp.179-190
• /
• 2000

The main object of this study was to investigate experimentally the characteristics of electrostatic cyclone-bag filter with upper tangential inlet in order to overcome the low collection efficiency for the submicron particle and high pressure drop which were main problems of general fabric bag filters. The experiment was carried out for the analysis of collection efficiency and pressure drop of electrostatic cyclone-bag filter comparing to those of fabric bag filter with various experimental parameters such as the inlet velocity(filtration velocity) and applied voltage etc. In the results the upper tangential inlet type showed higher collection efficiency for submicron particles below 2 ${\mu}{\textrm}{m}$ in diameter than that of center inlet and over 99.9% for overall collection efficiency. Pressure drop reduction ratios were shown as 40-50% for the applied voltage 0kV by centrifugal force and 70-90% for 20k V by the centrifuga and electrostatic force with the tangential inlet velocity (12-21m/s)

• 한국생산제조학회지
• /
• 제20권6호
• /
• pp.824-829
• /
• 2011

The mold is widely used for mass production in present industry. Also, product cycle time is faster, for this request, high productivity improvement in mold machining is required. And, In case of mold manufacturing company, the delivery shortening is required to quickly manufacture new product. Therefore, we aim for the delivery shortening though the method of machining time shortening in mold machining. On this paper, first, we made the NC-code of Insert die-casting as the object model using PowerMill. And then, analyzed cutting force by Toolpath in Insert mold machining using Production Module of Advantedge which is cutting force analysis program. After that, we came up with the optimum conditions of productivity improvement throughout the analysis result of before and after optimization of cutting force, machining time variation, and surface roughness by changing min tangential force to 80, 85, 90% of max tangential force.

• 한국정밀공학회지
• /
• 제15권10호
• /
• pp.140-147
• /
• 1998

The dynamic behavior of elastically restrained beams under the action of distributed tangential forces is investigated in this paper. The beam, which is fixed at one end, is assumed to rest on an intermediate spring support. The governing equations of motion are derived from the energy expressions, and the finite element formulation is employed to calculate the critical distributed tangential force. Jump phenomena for the critical distributed tangential force and instability types are presented for various spring stiffnesses and support positions. Stability maps are generated by performing parametric studies to show how the distributed tangential forces affect the frequencies and the stability of the system considered. Through the numerical simulations, the following conclusioils are obtained: (i) Only flutter type instability exists for the dimensionless spring stiffness K $\leq$ 97, regardless of the position of the spring support. (ii) For the dimensionless spring stiffness K $\leq$ 98, the transition from flutter to divergence occurs at a certain position of the spring support, and the transition position moves from the free end to the free end of the beam as the spring stiffness increases. (iii) For K $\leq$ 10$^{6}$ the support condition can be regarded as a rigid support condition.

• 한국산학기술학회논문지
• /
• 제17권10호
• /
• pp.21-26
• /
• 2016

산업체에서 널리 사용되고 있는 유도전동기의 회전자를 제작하기 위하여 rotor core slot에 Cu bar를 열박음(shrinkage fit)작업으로 고정한 후 bar 표면을 punch로 원주방향으로 순차적으로 1.5~3mm 압입(swaging)작업시 rotor core slot과 bar 접촉면에 작용하는 contact tangential force의 크기와 분포를 단순화된 2차원 plane strain 해석모델을 사용하여 각각의 압입조건에 대하여 평가하였으며 또한 생산성 향상을 고려한 rotor core slot 설계시 slot 형상에 따른 접촉력 분포를 평가하여 rotor core slot 설계시 필요한 정보를 제공하고자 수치해석적인 방법을 사용하여 parametric study를 수행하였다. 이러한 탄소성 수치해석 결과 1) rotor core 압입작업시 bar 접촉면에 작용하는 contact force는 소성변형이 먼저 발생하는 bar 상부에 크게 작용하며 2) 순차적인 rotor core 압입작업시 bar 접촉면에 작용하는 total contact force는 바로 인접한 bar에 대한 압입작업에 의해서만 영향을 받으며 그 영향으로 약 55% 정도 total contact force가 증가하며 3) 생산성을 고려하여 rotor core를 설계하는 경우에 contact force를 증가시키기 위해서는 core slot의 폭보다 길이를 길게 하는 것이 바람직하다는 사실을 알 수 있었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.701-705
• /
• 2000

On the dynamic behavior of a simple beam subjected to an uniformly distributed tangential follower force, the influences of the velocities and magnitudes of a moving mass have been studied by numerical method. The instant amplitude of a simple beam is calculated and analyzed for each position of the moving mass represented by the time functions. The uniformly distributed tangential follower force is considered in its critical value of a simple beam, and four values of velocity is also chosen. Their coupling effects on the deflections of a simple beam are inspected too. When a moving mass moves after middle zone of a simple beam at the low velocities, its deflection is increased by the coupling of an uniformly distributed tangential follower force and moving mass.

• 한국정밀공학회지
• /
• 제10권2호
• /
• pp.190-196
• /
• 1993

Internal high speed grinding under several high grinding wheel speed condition has been performed in this study for the effects have analyzed and compared with the grinding power, grinding tangential force and accuracy of surface with the carbon tool steel(SK3). The following results have been obtained: (1) Under the workpiece speed constant condition, increasing the grinding speed, the tangential force is decreased, and on the contrary, accuracy of surface is improved. (2) Under the speed ratio (V$_{w}$/V$_{s}$) contant condition it is possible to increase the high machining efficiency constraint to tangential grinding force constant.ant.

• 한국소음진동공학회논문집
• /
• 제13권3호
• /
• pp.202-209
• /
• 2003

A simply supported beam subjected to a uniformly distributed tangential follower force and the two successively moving spring-mass systems upon it constitute this vibration system. The influences of the velocities of the moving spring-mass system, the distance between two successively moving spring-mass systems and the uniformly distributed tangential follower force have been studied on the dynamic behavior of a simply supported beam by numerical method. The uniformly distributed tangential follower force is considered within its critical value of a simply supported beam without two successively moving spring-mass systems, and three kinds of constant velocities and constant initial displacement of two successively moving spring-mass systems are also chosen. Their coupling effects on the transverse vibration of the simply supported beam are inspected too. In this study the simply supported beam is deflected with small vibration proportional to natural frequency of the moving spring-mass systems. According to the increasing of initial displacement of the moving spring-mass systems the amplitude of the small vibration of the simply supported beam is increased due to the spring force. The velocity of the moving spring-mass system more affect on the transverse deflection of simply supported beam than other factors of the system and the effect is dominant at high velocity of the moving spring-mass systems.

• 한국정밀공학회지
• /
• 제28권5호
• /
• pp.565-571
• /
• 2011

Because most fatigue cracks in wheel and rail take place by rolling contact of wheel and rail in railroad industry, it is critical to understand the rolling contact phenomena, especially for the three-dimensional situation. This paper presents an approach to steady-state rolling contact problem of three-dimensional contact bodies, with or without tangential force, based on the finite element method. The steady-state conditions are controlled by the applied relative slip and tangential force. The three-dimensional distribution of tangential traction and contact stresses on the contact surface are investigated. Results show that the distribution of tangential traction and contact stresses on the contact surface varies rapidly as a result of the variation of stick-slip region. The tangential traction is very close in form to Carter's distribution.