• Journal of KIISE:Computer Systems and Theory
• /
• v.34 no.5_6
• /
• pp.257-266
• /
• 2007

In On-Chip bus, the arbitration scheme is one of the critical factors that decide the overall system performance. The arbitration scheme used in traditional shared bus is the master-side arbitration based on the request and grant signals between multiple masters and single arbiter. In the case of the master-side arbitration, only one master and one slave can transfer the data at a time. Therefore the throughput of total bus system and the utilization of resources are decreased in the master-side arbitration. However in the slave-side arbitration, there is an arbiter at each slave port and the master just starts a transaction and waits for the slave response to proceed to the next transfer. Thus, the unit of arbitration can be a transaction or a transfer. Besides the throughput of total bus system and the utilization of resources are increased since the multiple masters can simultaneously perform transfers with independent slaves. In this paper, we implement and analyze the arbitration schemes for the Multi-Layer AHB BusMatrix based on the slave-side arbitration. We implement the slave-side arbitration schemes based on fixed priority, round robin and dynamic priority and accomplish the performance simulation to compare and analyze the performance of each arbitration scheme according to the characteristics of the master and slave. With the performance simulation, we observed that when there are few masters on critical path in a bus system, the arbitration scheme based on dynamic priority shows the maximum performance and in other cases, the arbitration scheme based on round robin shows the highest performance. In addition, the arbitration scheme with transaction based multiplexing shows higher performance than the same arbitration scheme with single transfer based switching in an application with frequent accesses to the long latency devices or memories such as SDRAM. The improvements of the arbitration scheme with transaction based multiplexing are 26%, 42% and 51%, respectively when the latency times of SDRAM are 1, 2 and 3 clock cycles.

• Journal of KIISE:Computer Systems and Theory
• /
• v.34 no.5_6
• /
• pp.202-213
• /
• 2007

A network is an important model widely used in natural and social science as well as engineering. To analyze these networks easily it is necessary that we should layout the features of networks visually. These Graph-Layout researches have been performed recently according to the development of the computer technology. Among them, the Scale-free Network that stands out in these days is widely used in analyzing and understanding the complicated situations in various fields. The Scale-free Network is featured in two points. The first, the number of link(Degree) shows the Power-function distribution. The second, the network has the hub that has multiple links. Consequently, it is important for us to represent the hub visually in Scale-free Network but the existing Graph-layout algorithms only represent clusters for the present. Therefor in this thesis we suggest Graph-layout algorithm that effectively presents the Scale-free network. The Hubity(hub+ity) repulsive force between hubs in suggested algorithm in this thesis is in inverse proportion to the distance, and if the degree of hubs increases in a times the Hubity repulsive force between hubs is ${\alpha}^{\gamma}$ times (${\gamma}$??is a connection line index). Also, if the algorithm has the counter that controls the force in proportion to the total node number and the total link number, The Hubity repulsive force is independent of the scale of a network. The proposed algorithm is compared with Graph-layout algorithm through an experiment. The experimental process is as follows: First of all, make out the hub that exists in the network or not. Check out the connection line index to recognize the existence of hub, and then if the value of connection line index is between 2 and 3, then conclude the Scale-free network that has a hub. And then use the suggested algorithm. In result, We validated that the proposed Graph-layout algorithm showed the Scale-free network more effectively than the existing cluster-centered algorithms[Noack, etc.].

• Clinical and Experimental Pediatrics
• /
• v.49 no.5
• /
• pp.533-538
• /
• 2006

Purpose : The headache, one of the symptoms of meningitis, is related to abrupt elevation of intracranial pressure(ICP) or stimulation of intracranial nociceptive structure. However, in cases of mild elevation of ICP or normal findings of cerebrospinal fluid(CSF) analysis, patients sometimes complain of headaches. Therefore, other pathways may contribute to the occurrence of headaches in aseptic meningitis or meningismus. We intend to investigate the role of substance P(SP) and calcitonin gene-related peptide(CGRP) in aseptic meningitis or meningismus. Methods : We measured leukocyte count, the concentration of protein and glucose in CSF and ICP of patients with meningeal irritation sign. We also measured SP and CGRP levels by using immunoassay. We analyzed the relationship between the presence of headache and the value of SP and CGRP. Results : The concentrations of CGRP($18.8{\pm}10.5ng/mL$) in CSF and ICP($14.8{\pm}4.5cmH_2O$) in aseptic meningitis group were significantly higher than in those($14.1{\pm}7.4ng/mL$ and $12.0{\pm}5.1cmH_2O$, respectively) of the meningismus group(P<0.05). There was no significant difference in the SP levels between the two groups. In the aseptic meningitis group, the concentrations of SP and CGRP were significantly higher in the normal ICP group than in the elevated ICP group(P<0.05). Conclusion : Headaches in children with aseptic meningitis or meningismus is considered to be related to the elevation of the CSF levels of SP and CGRP.

• Clinical and Experimental Pediatrics
• /
• v.52 no.6
• /
• pp.655-660
• /
• 2009

Purpose : To compare birth weight between infants with a single umbilical artery (SUA) and normal infants, investigate the associated anomalies of infants with SUA and isolated SUA (no abnormality of external appearance on birth, except SUA), and determine the prognosis of infants with isolated SUA. Methods : Live-born infants with SUA (n=59) detected by physical examination from among 15,193 live births in seven university hospitals in Korea between January 1, 2004, to August 1, 2007, were reviewed retrospectively, with 236 normal infants serving as the control group. Results : A statistical difference was observed between the groups in birth weight and in vitro fertilization. The incidence of infants with SUA was 0.37%. Congenital malformations were observed in 21 infants with cardiovascular (n=15, 25.4%), gastrointestinal (n=2, 3.4%), genitourinary (n=9, 15.3%), neuromusculoskeletal (n=6, 10.2%), central nervous system (n=1, 1.7%), chromosomal (n=1, 1.7%), and other (n=3, 5.1%) abnormalities. There were 49 (83.1%) infants with isolated SUA in this study population; among them, the associated congenital malformations were cardiovascular (n=6, 12.2%) and genitourinary (n=6, 12.2%) abnormalities. Two infants with cyanotic heart disease were operated and four infants with acyanotic heart disease showed improvements without any treatment. Six infants with genitourinary abnormalities on renal ultrasound had mild hydronephrosis without further consequences. Conclusion : The incidence of structural abnormalities in the cardiovascular and genitourinary systems is high and the genitourinary anomalies associated with isolated SUA have relatively good prognosis.

• Journal of Bio-Environment Control
• /
• v.20 no.2
• /
• pp.93-100
• /
• 2011

Maintenance of adequate soil water potential during the period of crop growth is necessary to support optimum plant growth and yields. A better understanding of soil water movement within and below the rooting zone can facilitate optimal irrigation scheduling aimed at minimizing the adverse effects of water stress on crop growth and development and the leaching of water below the root zone which can have adverse environmental effects. The objective of this study was to evaluate the feasibility of using a portable irrigation controller with an Watermark sensor for the cultivation of drip-irrigated vegetable crops in a greenhouse. The control capability of the irrigation controller for a soil water potential of -20 kPa was evaluated under summer conditions by cultivating 45-day-old tomato plants grown in three differently textured soils (sandy loam, loam, and loamy sands). Water contents through each soil profile were continuously monitored using three Sentek probes, each consisting of three capacitance sensors at 10, 20, and 30 cm depths. Even though a repeatable cycling of soil water potential occurred for the potential treatment, the lower limit of the Watermark (about 0 kPa) obtained in this study presented a limitation of using the Watermark sensor for optimal irrigation of tomato plants where -20 kPa was used as a point for triggering irrigations. This problem might be related to the slow response time and inadequate soil-sensor interface of the Watermark sensor as compared to a porous and ceramic cup-based tensiometer with a sensitive pressure transducer. In addition, the irrigation time of 50 to 60 min at each of the irrigation operation gave a rapid drop of the potential to zero, resulting in over irrigation of tomatoes. There were differences in water content among the three different soil types under the variable rate irrigation, showing a range of water contents of 16 to 24%, 17 to 28%, and 24 to 32% for loamy sand, sandy loam, and loam soils, respectively. The greatest rate increase in water content was observed in the top of 10 cm depth of sandy loam soil within almost 60 min from the start of irrigation.

• Journal of Bio-Environment Control
• /
• v.17 no.1
• /
• pp.26-31
• /
• 2008

This experiment were conducted to investigate the response of growth and yield of potato after transplanting of plug seedlings 'Superior' and 'Dejima' produced at different plug cell size (105, 162, and 288) and photoperiod (8/16, 12/12, and 16/8, day/night) for 20 days in controlled plant growth system. Growth and relative growth rate of plug seedling 'Superior' was affected by plug cell size and photoperiod at 7weeks after transplanting. Tuber weight of 'Superior' was increased as cell size and photoperiod increased. That of 'Dejima' was highest in 105 cell and different with photoperiod. At 90 days after transplanting, tuber weight ($258.9{\sim}471.9\;g/plant) of 'Superior' was high in 105 and 162 cell size and 16/8 hr photoperiod. That ($278.2{\sim}428.0\;g/plant$) of 'Dejima' was high in 105 cell size, but was not different with photoperiod. The number of tuber per plant was $2.6{\sim}6.9$ of 'Superior' and $2.2{\sim}3.6$ 'Dejima'. Tuber number per plant was not significantly different with cell size and photoperiod. The large tuber over 80 g was $32.0{\sim}50.9%$ of 'Superior' and $41.0{\sim}56.7%$ of 'Dejima'. The large tuber in 'Superior' and 'Dejima' lowered as the cell size decreased. The large tuber of 'Superior' increased as photoperiod increased, but that of 'Dejima' was not differed. As the results, the optimal plug cell size and photoperiod of potato seedling is considered to be below 162 cell and over 12 hr of photoperiod.

• Composites Research
• /
• v.12 no.4
• /
• pp.71-78
• /
• 1999

To determine the effect of chemical structure of linear amine curing agents on thermal and mechanical properties, standard epoxy resin DGEBA was cured with diaminodiphenyl methane (DDM), diaminodiphenyl sulphone (DDS) in a stoichiometrically equivalent ratio. From this work, the effect of aromatic amine curing agents. In contrast, the results show that the DGEBA/DDS cure system having the sulfone structure between the benzene rings had higher values in the conversion of epoxide, density, shrinkage (%), glass transition temperature, tensile modulus and strength, flexural modulus and strength than the DGEBA/DDM cure system having methylene structure between the benzene rings, whereas the DGEBA/DDM cure system presented higher values in the maximum exothermic temperature, thermal expansion coefficient, and thermal stability. These results are caused by the relative effects of sulfone group having strong electronegativity and methylene group having (+) repulsive property and stem from the effect of the conversion ratio of epoxide group. The result of fractography shows that the each grain size of the DDM/DGEBA system with feather-like structure is larger than that of the DDS/DGEBA system.

• 대한공업교육학회지
• /
• v.38 no.1
• /
• pp.49-67
• /
• 2013

The purpose of this study is to analyze the external systems and the units 'problem solving and invention' of the middle school technology and home economics 1 textbooks of the revised 2011 national curriculum in an effort to provide some information on the content system of invention education in technology class, as invention education was provided as part of a regular subject for the first time. The findings of the study were as follows: First, 'Technology and Inventions' chapter of Technology and Home Economics 1 Textbooks occupied 10-18% share, with the subchapter of 'Problem Solving and Invention' unit taking up 6.7-29% of the textbooks. Second, for most textbooks, 'Technological Problem Solving', 'Idea Generation' 'Multi-dimensional Projection Method', 'Expansive Thought-Processing Methodology', 'Converging Thought Methodology' and 'Invention in Everyday Lives' were included as main contents based on the accomplishment criteria presented in education process interpretation documents. Third, the detailed structures were generally made up as follows: Introduction (Broad Chapter Title, Subchapter Table of Contents, Introduction, Subchapter Title, Study Objectives, Open Thinking); Development (Unit Title, Thinking Ahead, Core Terms, Main Text, Study Helper, Activities, Research Exercises, Supplemental Readings, In-depth Study Topics, Technology in Everyday Lives, Reading Topics, Discussion Topics, and Career Helpers); and Summary (Subchapter Summary, Study Summary, Terms Summary, Writing Follow-up, Self Review, Broad Chapter Evaluation). Fourth, based on the analysis of figures included, photographs had the largest share, followed by figures, tables, and graphs. The photos were used to illustrate various inventions, invention methodologies, and exercise activities, while figures were included to depict the contents included in the main text, and the tables to assist to preparation of process diagrams or materials lists. Fifth, based on the analysis of content weights, greater weights were placed on 'Inventions and Thoughts', and 'Invention Experiment Activities,' while 'Understanding Inventions' and 'Invention and Patents' chapters did not have a lot of texts involved. Sixth, based on the analysis of content presentation methods, most textbooks combined figures, tables, illustrations and texts to discuss the topics. Based on the above study results, we suggest the following: First, a consistent education curriculum should be developed over the topic of invention; and second, more precise and systematic analysis of textbooks would need to be performed.

• Progress in Medical Physics
• /
• v.19 no.4
• /
• pp.276-284
• /
• 2008

A computed tomography (CT) is a powerful system for the effectively fast and accurate diagnosis. The CT system, therefore, has used substantially and developed for improving the performance over the past decade, resulting in growing concerns over the radiation dose from the CT. Advanced CT techniques, such as a multidetector row CT scanner and dual energy or dual source CT, have led to new clinical applications that could result in further increases of radiation does for both patients and workers. The objective of this study was to review the international guidelines of the shielding requirements for a CT facility required for a new installation or when modifying an existing one. We used Google Search Engine to search the following keywords: computed tomography, CT regulation or shield or protection, dual energy or dual source CT, multidetector CT, CT radiation protection, and regulatory or legislation or regulation CT. In addition, we searched some special websites, that were provided for sources of radiation protection, shielding, and regulation, RSNA, AAPM, FDA, NIH, RCR, ICRP, IRPA, ICRP, IAEA, WHO (See in Table 1 for full explanations of the abbreviations). We finally summarized results of the investigated materials for each country. The shielding requirement of the CT room design was very well documented in the countries of Canada, United States of America, and United Kingdom. The wall thickness of the CT room could be obtained by the iso-exposure contour or the point source method. Most of documents provided by international organizations were explained in importance of radiation reduction in patients and workers. However, there were no directly-related documents of shielding and patient exposure dose for the dual energy CT system. Based international guidelines, the guideline of the CT room shielding and radiation reduction in patients and workers should be specified for all kinds of CT systems, included in the dual energy CT. We proposed some possible strategies in this paper.

• Progress in Medical Physics
• /
• v.19 no.4
• /
• pp.209-218
• /
• 2008

According to improved radiation therapy technology such as IMRT and proton therapy, the accuracy of patient alignment system is more emphasized and IGRT is dominated research field in radiation oncology. We proposed to study the feasibility of cone-beam CT system using simple x-ray imaging systems for image guided proton therapy at National Cancer Center. 180 projection views ($2,304{\times}3,200$, 14 bit with 127 ${\mu}m$ pixel pitch) for the geometrical calibration phantom and humanoid phantoms (skull, abdomen) were acquired with $2^{\circ}$ step angle using x-ray imaging system of proton therapy gantry room ($360^{\circ}$ for 1 rotation). The geometrical calibration was performed for misalignments between the x-ray source and the flat-panel detector, such as distances and slanted angle using available algorithm. With the geometrically calibrated projection view, Feldkamp cone-beam algorithm using Ram-Lak filter was implemented for CBCT reconstruction images for skull and abdomen phantom. The distance from x-ray source to the gantry isocenter, the distance from the flat panel to the isocenter were calculated as 1,517.5 mm, 591.12 mm and the rotated angle of flat panel detector around x-ray beam axis was considered as $0.25^{\circ}$. It was observed that the blurring artifacts, originated from the rotation of the detector, in the reconstructed toomographs were significantly reduced after the geometrical calibration. The demonstrated CBCT images for the skull and abdomen phantoms are very promising. We performed the geometrical calibration of the large gantry rotation system with simple x-ray imaging devices for CBCT reconstruction. The CBCT system for proton therapy will be used as a main patient alignment system for image guided proton therapy.