• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.11
• /
• pp.1606-1610
• /
• 2012

Hysteresis current regulator has been used widely because of its simple principle and structure. However, when the current band width is too narrow or the applied voltage is relatively too high, the switching frequency may increase abruptly and it generates a large amount of heat. Thus, this study will suggest a better and simple method to reduce the switching frequency. For single phase current control, the proposed hysteresis current control is executed by adding 0 mode state and comparing the slope of the current reference. This simple method decreases the generated switching frequency and significantly reduces the generated heat. This proposed method was proved with simulations and experiments comparing with the classical hysteresis current control method.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1009_1010
• /
• 2009

This paper presents a power supply system with pre-regulator using zero voltage switching (ZVS) interleaving two-transistor forward converter for high input voltage and high power application. A SMPS has a advantage that a good efficiency, small size and light weight but has a noise problem. A linear power supply system has a advantage that a good stability, low ripple and noise but has a disadvantage that a big size, low efficiency and heat problem. To alleviate these problems, we propose an power supply system using dual ZVS interleaving two-transistor forward pre-regulator. The proposed converter is verified on a 1kW, 50kHz experimental prototype.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.270-275
• /
• 1998

A new single phase power factor correction rectifier/regulator with dc linked energy feedback circuit is proposed, which is capable of achieving the zero voltage switching (ZVS) of a boost rectifier stage without any auxiliary switch. The performance of the proposed rectifier/regulator is demonstrated through a 200W, 90 KHz prototype. This proposed rectifier/regulator with dc linked energy feedback circuit is particularly suited for distributed power system applications

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.399-402
• /
• 1988

In this paper, the relationship between stability and gain band-width product (GB) is clear ed by evaluating the feedback gain in the buck-boost switching regulator. Especially, considering the effect of the right-half-plane pole on the stability, we found available region of GB on the stability with the one pole compensation for the feedback circuit.

• 제어로봇시스템학회:학술대회논문집
• /
• 1986.10a
• /
• pp.576-579
• /
• 1986

In this paper, a design method of an optimal output PIM(Proportional-Integral-Measurable) controller is presented so that the closed-loop output response of the switching regulator closely match to that of ideal model system satisfying the time domain specifications. The computer simulation for a design example is given to show the usefulness of the proposed technique.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2531-2533
• /
• 2001

This paper describes a low noise and high efficiency analog-digital switching mixed mode battery charger for production facilities of Li-Ion batteries. The requirements for battery chargers for production facilities are very strict. The accuracy of output voltage and output current should be below 0.1% with very low ripple current. Therefore analog type linear regulators are widely used for battery charger in spite of their inefficiency and bulkiness. We combined linear regulator as a voltage source with digital switching converter as a dependent current source. Low current ripple and high accuracy are obtained by linear regulator while high efficiency is achieved by digital switching converter. Experimental results show that proposed method has 0.1% ripple and 90% efficiency at an output current of 1A for a battery voltage of 4V.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.544-547
• /
• 1989

The introduction of resonant link inverters has allowed the use of much higher switching frequencies in induction motor current regulators. The resonant link inverter,however, requries the use of discrete time switching strategies. This type of controller,while giving the best possible performance, is difficult to implement, since motor parameters must be calculated or measured. The delta modulated current regurator (DMCR) has been introduced as a controller without additional state feedback. A discrete pulse modulated current regulator which controls load current is introduced in the paper.

• Journal of Electrical Engineering and information Science
• /
• v.3 no.1
• /
• pp.14-20
• /
• 1998

The resistive shunting for the fine control of a Direct Energy Transfer(DET) systems is fully developed, but the non-resistive shunting using variable size solar array segments is in progress. This paper presents the spacecraft power control through switching of solar array segments, which uses a fully regulated DET power regulation. This method eliminates a dissipative element and removes the associated design limitations which arise from the dissipative elements for radiating cooling in deep space. The switching shunt regulator comprises the switched Solar Array Shunt(SAS) modules that regulate the solar array power. These SAS modules connect/disconnect the solar array segments to/from the bus according to the loading in the main bus without significant variations in the dissipation level. In this paper, twelve segments are used in the shunting. In order to verify the basis of analysis, the computational result of an analytic loop gain is performed.

• Proceedings of the KIEE Conference
• /
• 1999.11b
• /
• pp.364-368
• /
• 1999

This paper suggests switching regulator technique to overcome the drawback of conventional variable linear power supply. Switching regulator technique can eliminate the extremely lossy operation and reduce the size and weight of variable linear power supply and provide nearly constant output power over the majority of output voltage range. The topology of variable switched mode power supply is employed active clamp forward converter with a current doubler rectifier and by using control of variable-frequency together with control of fixed-frequency, output voltage can be controled. Equivalent circuits pertinent to each operational mode of converter are derived, and an experimental 20V, 50A converter was designed and built. The converter operates from an output voltage of zero to 25 V, under 100 kHz switching frequency.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.758-761
• /
• 2003

We have designed 5 V/500 mA transless type power module by using semiconductor switching technique, key technique for small size of power supply system. The power module is suitable to a small sized electronic system using a single power supply. It is composed of switching circuit using voltage drop type chopper method, control circuit, voltage detect circuit, and constant voltage circuit, and is fabricated to hybrid-IC type. The switching regulator power supply circuit, designed in this study, has satisfied the electrical characteristics of 5 V/500 mA transless type power module.