• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.6
• /
• pp.465-471
• /
• 2007

The system efficiency of the proposed Buck-Boost AC-DC converter is increased by soft switching method. The converter includes to merit of power factor correction (PFC) from sinusoidal control of input current. The switching behavior of control switches operates with soft switching by partial resonance, and then the proposed converter has high system efficiency with decrement of switching power loss. The input current waveform in proposed converter is got to be a sinusoidal form of discontinuous quasi-pulse row in proportion to magnitude of AC input voltage under the constant duty cycle switching. Therefore, the input power factor is nearly unity. The output voltage of the converter is regulated by PWM control technique. The discontinuous mode action of current flowing into inductor makes to simplify control method and control components. The proposed PFC Buck-Boost converter is analyzed to compare with the conventional PFC Buck-Boost converter. Some computer simulative results and experimental results confirm to the validity of the analytical results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.2A
• /
• pp.201-206
• /
• 2006

A SPST Switch MMIC which used for Microwave Switch Matrix(MSM) of communications satellite payload with multi-beam function has been designed and fabricated. New RE FET switch configuration has been devised to improve power characteristics and isolation. Input and output return losses are better than another switches reported previously for both On and Off states. The MMIC chips were fabricated in 0.15um GaAs pHEMT process and measured insertion loss less than 2.0dB and isolation more than 63dB in the frequency range of 3GHz$\∼$4GHz. Output 3rd order interceptpoint above 32dBm has been recorded and the value is very high even though the unit pHEMT has gate width of 0.2mm and only four pHEMT are used in the MMTC.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.2A
• /
• pp.79-85
• /
• 2006

Generally, it is essential that high-speed routers, switches, and network security appliances should have an efficient packet classification scheme in order to achieve the high-speed packet forwarding capability. For the multi-gigabit packet-processing network equipment the high-speed content search hardware such as TCAM and search engine is recently used to support the content-based packet inspection. During the packet classification process, hundreds and thousands of rules are applied to provide the network security policies regarding traffic screening, traffic monitoring, and traffic shaping. In addition, these rules could be dynamically changed during operations of systems if anomaly traffic patterns would vary. Particularly, in the high-speed network, an efficient algorithm that updates and reorganizes the packet classification rules is critical so as not to degrade the performance of the network device. In this paper, we have proposed an efficient update algorithm using a partial-ordering that can relocate the dynamically changing rules at the TCAM. Experimental results should that our algorithm does not need to relocate existing rules feature until 70$\%$ of TCAM utilization.

• Journal of the Korean Institute of Educational Facilities
• /
• v.7 no.3
• /
• pp.5-14
• /
• 2000

The purpose of this study is to analyze the environmental characteristics of Hansung Girls' Middle & High School located on the northern slope of Mt. Naksan in Seoul but sited at different aspects. The measured temperature and illumination in March, July and December were analysed. The proportion of window size and questionaries were used also. The results of observation are as follows: (1) The temperature of the southward classrooms was $3.6^{\circ}C$ higher than eastward or westward classrooms in March, but the difference of the both values in July were only $0.3^{\circ}C$ in the average. (2) The temperatures in December decreased in the order of aspects: southward, westward and eastward. (3) The highest values for illumination appeared in the classroom faced to the south and the values decreased from westward to eastward. (4) Temperatures and illumination were varied not only with the aspect but also with the number of story and the proportion of the window size. However, the heating facilities and illuminators are installed evenly without considering the condition of the buildings. The heating facilities should be installed differently according to the direction and height of the story of the building. The heating facilities should be installed sparsely for the classrooms faced southward, and more densely near the hallway side to achieve satisfaction of students and to save expenses of heating. It will be better that electric power switches for window side have to be set separately from hallway side. Improvement of the condition of illumination and temperatures will help students to promote their health and learning.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.51 no.9
• /
• pp.433-440
• /
• 2002

The addition of switches to a distribution feeder does, in general, increase reliability by decreasing the duration of the outage of many to the customers on the feeder. To cover its service area so that feeder-level delivery reaches sufficiently close to all customers, feeders typically split their routes many times, in what is often called a lateral feeder. It is interesting to note, however, that the effectiveness of a switch is very much dependent on the types of lateral feeder. The types of lateral are classified into two types. The first is loop lateral feeder that can connect its load to an adjacent feeder through a tie line in case that a fault occurs in its feeder and it is laid out so that every feeder has complete fault backup through re-switching of its loads to other sources like a main feeder The second is the radial lateral feeder cannot connect its load to an adjacent line, no provision is made for contingency backup of feeders. There are no other circuits in the radial lateral feeder form which to restore power. In this study, we evaluate the effectiveness of a switch installation between on the radial and loop lateral feeders to increase reliability by decreasing the duration of the outage. These results can help power utility to design the switch layouts on the radial and loop lateral feeder system.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.9
• /
• pp.456-465
• /
• 2001

In this paper, breakdown voltages in $SF_6-N_2$ mixtures were experimentally investigated to understand characteristics of dielectric strength and physical phenomena in nonuniform field disturbed by a needle shape protrusion. The test voltages are the lightning impulse$(\pm1.2/44 \mus)$ and the damped oscillatory impulse$(\pm400 ns / 0.83 MHz)$ voltages which can be occurred by the operation of disconnecting switches in gas-insulated switchgears(GIS). The effects of the polarity and wave shape of the test voltages, and the gas pressure on the V-t characteristics were in detail examined. The V-t characteristic curves were measured in different two ways : (1) one is the method by taking the maximum voltage recorded at or prior to breakdown against the time to breakdown, that is, the Procedures recommended in IEC 60060-1, (2) the other is the method by taking the voltage at the instant of chopping against the time to breakdown. As a result, the V-t characteristics of $SF_6-N_2$ mixtures in nonuniform electric field were significantly affected by the polarity and wave shape of the applied voltages. The positive breakdown voltages resulted in lower breakdown voltages in the time ranges considered, and the V-t curves for the negative oscillatory impulse voltage were extended over the longer time range. For the lightning impulse voltages, the V-t curves obtained by IEC Pub. 60060-1 were nearly same with the V-t curves obtained by the voltage at the instant of chopping against the time to breakdown. It is clear that the actual breakdown voltages were much lower than the maximum voltages appearing at or prior to breakdown because of the displacement current produced as a result of the dV/dt during the oscillatory transient voltage app1ication. The scattering of the negative actual breakdown voltages was much larger than that of the positive.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.2
• /
• pp.92-97
• /
• 2016

This paper presents design and simulation of wide band RF microswitch that uses electrostatic actuation for its operation. RF MEMS devices exhibit superior high frequency performance in comparison to conventional devices. Similar techniques that are used in Very Large Scale Integration (VLSI) can be employed to design and fabricate MEMS devices and traditional batch-processing methods can be used for its manufacturing. The proposed switch presents a novel design approach to handle reliability concerns in MEMS switches like dielectric charging effect, micro welding and stiction. The shape has been optimized at actuation voltage of 14-16 V. The switch has an improved restoring force of 20.8 μN. The design of the proposed switch is very elemental and primarily composed of electrostatic actuator, a bridge membrane and coplanar waveguide which are suspended over the substrate. The simple design of the switch makes it easy for fabrication. Typical insertion and isolation of the switch at 1 GHz is -0.03 dB and -71 dB and at 85 GHz it is -0.24 dB and -29.8 dB respectively. The isolation remains more than - 20 db even after 120 GHz. To our knowledge this is the first demonstration of a metal contact switch that shows such a high and sustained isolation and performance at W-band frequencies with an excellent figure-of merit (fc=1/2.pi.Ron.Cu =1,900 GHz). This figure of merit is significantly greater than electronic switching devices. The switch would find extensive application in wideband operations and areas where reliability is a major concern.

• Journal of the Ergonomics Society of Korea
• /
• v.34 no.2
• /
• pp.85-101
• /
• 2015

Objective: The purpose of this study was to develop and evaluate smart secondary controls using iPad for the drivers with physical disabilities in the driving simulator. Background: The physically disabled drivers face problems in the operation of secondary control devices that accept a control input from a driver for the purpose of operating the subsystems of a motor vehicle. Many of conventional secondary controls consist of small knobs or switches that physically disabled drivers have difficulties in grasping, pulling or twisting. Therefore, their use while driving might increase distraction and workload because of longer operation time. Method: We examined the operation time of conventional and smart secondary controls, such as hazard warning, turn signal, window, windshield wiper, headlights, automatic transmission and horn. The hardware of smart secondary control system was composed of iPad, wireless router, digital input/output module and relay switch. We used the STISim Drive3 software for driving test, customized Labview and Xcode programs for interface control of smart secondary system. Nine subjects were involved in the study for measuring operation time of secondary controls. Results: When the driver was in the stationary condition, the average operation time of smart secondary devices decreased 32.5% in the normal subjects (p <0.01), 47.4% in the subjects with left hemiplegic disabilities (p <0.01) and 38.8% in the subjects with right hemiplegic disabilities (p <0.01) compared with conventional secondary devices. When the driver was driving for the test in the simulator, the average operation time of smart secondary devices decreased 36.1% in the normal subjects (p <0.01), 41.7% in the subjects with left hemiplegic disabilities (p <0.01) and 34.1% in the subjects with right hemiplegic disabilities (p <0.01) compared with conventional secondary devices. Conclusion: The smart secondary devices using iPad for people with hemiplegic disabilities showed significant reduction of operation time compared with conventional secondary controls. Application: This study can be used to design secondary controls for adaptive vehicles and to improve the quality of life of the people with disabilities.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.4 s.334
• /
• pp.15-20
• /
• 2005

Multi-Input, Multi-Output system suffers for the spatial channel correlation due to lack of spatial diversity. To overcome this defect, the antenna selection and switching system is proposed which selects the adequate antenna subset with highest channel diversity gain and switches the trasmission techniques according to channel environments. However. its performance analysis is insufficient due to the difficulty of modeling the spatial channel correlation. In this paper, the theoretical upper bound of symbol error probability is derived by using the statistical properties of Frobenius norm and minimum eigen-value of channel matrix. By computer simulation, it is shown that the derived theoretical upper bound is similar to the simulation results.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.5
• /
• pp.1-12
• /
• 1999

A new algorithm of constructing binary decision diagram(BDD) for design verification of switch-level circuits is proposed in this paper. In the switch-level circuit, functions are characterized by serial and parallel connections of switches and the final logic values may have high-impedance and unstable states in addition to the logic values of 0 and 1. We extend the BDD to represent functions of switch-level circuits as acyclic graphs so called switch-level binary decision diagram (SLBDD). The function representation of the graph is in the worst case, exponential to the number of inputs. Thus, the ordering of decision variables plays a major role in graph sizes. Under the existence of pass-transistors and domino-logic of precharging circuitry, we also propose an input ordering algorithm for the efficiency in graph sizes. We conducted several experiments on various benchmark circuits and the results show that our algorithm is efficient enough to apply to functional simulation, power estimation, and fault-simulation of switch-level design.