• Journal of Power Electronics
• /
• v.10 no.6
• /
• pp.667-672
• /
• 2010

A way how to teach a general understanding of switched mode power supplies (SMPS) is shown. A fourth order PWM DC-to-DC converter with limited duty cycle range is treated as an example and a survey over important data (maximum voltage and current ratings for the elements, rms- values for the semiconductor devices and a rough approximation of the losses) of the circuit is given. Furthermore, a converter model based on duty ratio averaging is established. Continuous mode of operation is used. The results make it possible to estimate the applicability of the given converter structure and offer sufficient material for the calculation, design, and analysis and give a better insight into switched mode energy conversion.

• Journal of Power Electronics
• /
• v.10 no.3
• /
• pp.219-227
• /
• 2010

Telecom supplies need to conform to low Total Harmonic Distortion (THD) and high Power Factor (PF) as per IEC 61000-3-2 and IEEE 519-1992 standards. These high rating power supplies use a three phase utility in which low THD and high PF are realized via various passive and active wave shaping schemes. In this paper, a new design for three phase telecom power supplies is presented with circuit parameter values optimized for high performance in terms of a low THD, high PF, low ripple and high line and load regulation using a suitable combination of various strategies. The performance of the power supply is validated by extensive simulations.

• The Magazine of the IEIE
• /
• v.18 no.5
• /
• pp.1-3
• /
• 1991

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.4
• /
• pp.137-142
• /
• 2023

When designing a SMPS(Switched Mode Power Supply) circuit, a part that is easily overlooked without special consideration is a snubber circuit. However, the performance degradation of the SMPS due to the snubber circuit and the effect on the entire SET cannot be ignored. In addition, a snubber circuit is added to both ends of the switch to protect the device from peak voltage and current during switching and to reduce loss during on/off switching. Therefore, in this paper, for a sufficient understanding of snubber circuits, theoretical analysis and experimental formulas that can be applied by designers during actual circuit design are arranged to promote optimization of snubber circuits.

• ETRI Journal
• /
• v.44 no.5
• /
• pp.759-768
• /
• 2022

A novel energy harvesting technique that uses conducted electromagnetic interference as an energy source is presented. Conducted EMI generated from fluorescent light using a switched-mode power supply was measured and modeled as an equivalent voltage source. Two types of rectifier circuits-a bridge rectifier and a voltage doubler-were used as the harvesting devices for conducted EMI source. The matching networks were designed based on the equivalent model, and the harvested power was improved. The implemented energy harvester produces a regulated power over 68.9 mW and current over 15.1 mA while a regulated voltage can be selected between 3.3 V and 5 V. The proposed system shows the highest harvesting power indoor environment and can provide enough power for the Internet of Things devices.

• Journal of Korean Electronics
• /
• v.10 no.6
• /
• pp.37-41
• /
• 1990

SMPS의 발명은 종래의 Sinear Teachnology에 비하여 소형, 경량과 및 고효율을 이룩한 일대 혁신이었고 고신뢰성, 고저일, 다기능, Fast Respone Time을 추구하는 끊임없는 노력은 새로운 방법의 Switched Mode Technology로 발전되어 왔으며 최근에는 QRZ Technology의 발명으로 Power Supply의 설계기술에 또 하나의 혁신이 일어나고 있다.

• Journal of Electrical Engineering and Technology
• /
• v.5 no.3
• /
• pp.468-476
• /
• 2010

This paper presents a direct single-stage power converter using single-phase isolated full-bridge converter modules, with inherent power factor correction (PFC) for a 12 kW switched mode power supply (SMPS). The advantages of the proposed converter are its simple control strategy, reduction in number of conversion stage, low input line current harmonics, and improvement in power factor. Analysis of the single-stage converter is carried out in continuous conduction mode of operation. Steady-state analysis of the proposed converter is conducted to obtain converter parameters. A systematic design procedure is also presented for a 12k W converter with a design example. The effect of load variation on SMPS is also studied in order to demonstrate the effectiveness of the proposed converter for the complete range of load conditions. A set of power quality indices on input ac mains for an SMPS fed from a single-stage converter is also presented for easy comparison of their performance.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1891-1895
• /
• 2003

Switch-mode power supplies (SMPS) have become a major source of conducted electromagnetic interference (EMI) which is the combination between differential mode (DM) noise and common mode (CM) noise. This paper presents the conducted EMI reduction approach in flyback switched mode power supply by rerouting for circuit balance to reduce common mode noise. And differential mode noise can be reduce by adding $c_x$ capacitor across the input power line, and passive element to the gate drive of switching device MOSFET to slow down the switching times. This combination of our approach is the effective way to reduce the conducted EMI and it is also a cost effective for product design

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.2 no.1
• /
• pp.11-15
• /
• 2009

In this study, we have developed the SMPS(Switched-mode power supply) power module for the medical kit. It is used the medical kit for improved supplying power better than the existing power module in performance, safety and reliability. The developed SMPS(Switched-mode power supply) is composed of the three fundamental electronic circuits, first one is for converting AC power to DC power, second one is for converting to high frequency, and the other is for absorbing noise frequency and preventing malfunction. It is possible for developed SMPS module to enlarge applications for PC, home appliances, switchboard as well as medical instruments.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.2
• /
• pp.142-145
• /
• 2018

In this paper, we present a design technique for the suppression of common-mode(CM) noise in switched-mode power supply boards using the segmentation method. By applying the segmentation method, the example structure is decomposed into two segments with decoupling capacitors and a recombination matrix is extracted for the segments. The effects of the decoupling capacitor on CM noise suppression are examined. The simulation time is significantly reduced on using the segmentation method.