• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.2
• /
• pp.110-118
• /
• 2008

The regulated peak power tracking (RPPT) systems such as the series structure and the parallel structure are commonly used in the satellite space power system. However, this structure processes the solar array power to the load through two regulators during one orbit cycle, which reduces the energy transfer efficiency. The series-parallel structure for the RPPT system can improve the power conversion efficiency, but an additional regulator increases the cost, size and weight of the system. In this paper, a simplified series-parallel space power system that consists of two regulators is proposed. The proposed system has the similar energy transfer efficiency with the series-parallel structure by adding one switch to the series structure, which reduces the cost, size and the weight. The large signal stability analyses is provided to understand the four main modes of system operation. In order to compare the energy efficiency with a series structure, the simulation is performed. The experimental verifications are performed using a prototype hardware with TMS320F2812 DSP and 200W solar arrays.

• The Journal of the Korea Contents Association
• /
• v.13 no.5
• /
• pp.19-27
• /
• 2013

This paper implements the standby power control system composed of a master device and slave devices. The standby power is managed by cutting power supply after controlling the relay of a slave device based on the authentication of master device's RFID card. RFID interface and wireless communication module are embedded in a master device, and one master device is linked with many slave devices in wireless. Each slave device executes the operation needed in power control independently. We implements the function of manual power on/off system in a slave device, and the function of user ID enrollment by switch manipulation in a master device. Also this system can communicate bidirectionally in wireless and runs on TinyOS. The result of experiment shows that the user authentication is executed in a master device and this authenticated information is transmitted to a slave device in wireless, and standby power is cutted by controlling the relay of a slave device. Installing this system in a building or an office, we can expect energy saving.

• Journal of Korea Multimedia Society
• /
• v.12 no.1
• /
• pp.107-121
• /
• 2009

First reason for generation of standby power is because starting voltage must pass through from the source of electricity to IC. The second reason is due to current when IC is in operation. Purpose of this abstract is on structures of simple modules that automatically switch on or off through analysis of state on standby power and analysis of cutoff point patterns as well as application of algorithms. To achieve this, this paper is based on analysis of electric signals and modeling. Also, on/off cutoff criteria has been established for reduction of standby power. To find on/off cutoff point, that is executed algorithm of similar group and leading pattern group generation in the standby power state. Therefore, the algorithm was defined as an important parameter of the subtraction value of calculated between $1^{st}$ SCS, $2^{nd}$ SCS, and the median value of sampling coefficient per second from a wall outlet.

• Journal of Advanced Navigation Technology
• /
• v.19 no.5
• /
• pp.458-463
• /
• 2015

This paper suggests detection system for the movement of patient on bed based on IEEE802.15.4 by using pressure pad and guard sensor. The system is designed to detect ordinary activities of patients on bed as well as patients' falling from the bed while sleeping at night. The node that is installed at bed sends data to gather when the pressure pad and sensor of guard detect patients' activities and falling. These data sent to gather are transmitted to monitor at help desk by TCP/IP communication. To remove unnecessary data that occurred due to switch chattering during tossing and turning, timer of MCU is used. Also, Communication module can change transmission power to apply this system to various environments of hospital room. Therefore, the nurse can take care of patients on bed in real time with data about patients' conditions.

• Journal of Advanced Navigation Technology
• /
• v.21 no.3
• /
• pp.220-229
• /
• 2017

In this paper, To take advantage a variety of DC power as the boost DC-DC converter design specifications through the inductor L and capacitor C through PSPICE to calculate the best estimate of the value. Boost DC-DC converter with a switch device using IRF840 and reverse recovery time Schottky diodes with excellent with constant current controller using D10SC6M and resistance can be configured to considering the Power LED Module was driven by the production. Converter's switching frequency is 50 kHz, the first Duty Rate was made to increase gradually depending on the value of the detection were, 10 % in the output voltage. As a result, the simulated Boost Power LED driver characteristics is in comparison with the design specifications, 5% or less as the error was approximated. Finally, when input 15 V were offered, a stable output 24 V were obtained. and Dimming Control through the adjustment of brightness and current consumption were possible.

• The Journal of Korean Institute of Information Technology
• /
• v.16 no.12
• /
• pp.31-40
• /
• 2018

We designed and implemented the attachable smart adapter for the general management of each company's agricultural machine regardless of whether it is equipped with a CAN (Controller Area Network) module. The smart adapter consists of a main board (Raspberry Pi3B), which operates agricultural machine's management software in Linux environment, and a self-developed interface board for power adjustment and status sensing. For the status monitoring, a sensing interface using a serial input was defined between the smart adapter and the sensors of the agricultural machine, and the state diagram of the agricultural machine was defined for diagnosis. We made a panel to simulate the sensors of the agricultural machine using the switch's on/off contact point, and confirmed the status monitoring and diagnostic functions by inputting each state of the farm machinery from the simulator panel.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.6
• /
• pp.573-582
• /
• 2010

In this paper, X-band transceiver for high resolution wideband SAR systems is designed and fabricated. Also as a technique for enhancing the performance, error compensation algorithm is presented. The transceiver for SAR system is composed of transmitter, receiver, switch matrix and frequency generator. The receiver especially has 2 channel mono-pulse structure for ground moving target indication. The transceiver is able to provide the deramping signal for high resolution mode and select the receive bandwidth for receiving according to the operation mode. The transceiver had over 300 MHz bandwidth in X-band and 13.3 dBm output power which is appropriate to drive the T/R module. The receiver gain and noise figure was 39 dB and 3.96 dB respectively. The receive dynamic range was 30 dB and amplitude imbalance and phase imbalance of I/Q channel was ${\pm}$0.38 dBm and ${\pm}$3.47 degree respectively. The transceiver meets the required electrical performances through the individual tests. This paper shows the pulse error term depending on SAR performance was analyzed and range IRF was enhanced by applying the compensation technique.

• Journal of Internet Computing and Services
• /
• v.8 no.1
• /
• pp.33-45
• /
• 2007

Using switches and sensors informing the current on or off state, this paper suggests a sleeping control and remote monitoring system that not only can recognize the sleeping situations but also can control for keeping an appropriate sleeping situation remotely, And we show an example that this system is applied to the healthcare sleeping mat, Our system comprises the following 3 parts: a part for detecting the sleeping situations, a part for extracting sensing data and sending/receiving the relating situated data, and a part controlling and monitoring the all of sleeping situations. In details, in order to develop our system, we used the touch and pressure-sensitive sensors with On/Off functions for a purpose of the first part, The second part consists of the self-developed embedded board with the socket based communication as well as extracting real-time sensing data. And the third part is implemented by service modules for providing controlling and monitoring functions previously described. Finally, these service modules are implemented by the TMO scheme, one of real-time object-oriented programming models and the communications among them is supported using the TMOSM of distributed real-time middleware.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.745-752
• /
• 2016

In the era of the Internet of Things, where all physical objects are connected to the Internet, we suggest a remote control system using a Raspberry Pi single-board computer with ZigBee, which can turn an indoor light-emitting diode (LED) and a multiple-tap on and off, and with a smart phone can control the brightness of the LED as well as an electronic door lock. By connecting an infrared (IR) transmitter module to the Raspberry Pi, we can control home appliances, such as an air conditioner, and we can also monitor indoor images, indoor temperatures, and illumination by using a smart phone app. We developed a method of finding out IR transmission codes required for remote-controllable appliances with an AVR micro-controller. We suggest a method to remotely open and shut an office door by novating the door lock. The brightness level of an LED (between 0 and 10) can be controlled through a PWM signal generated by an ATmega88 microcontroller. A mutiple-tap is controlled using an ATmega32, a photo-coupler, and a TRIAC. The signals for measured temperature and illumination are converted from analog to digital by using the ATtiny44A microcontroller transmitting to a Raspberry Pi through SPI communication. Then, we connect a camera to the CSI head of the Raspberry Pi. We can turn on the smart multiple-tap for a certain period of time, or we can schedule the multi-tap to turn on at a specific time. To reduce standby power, people usually pull out a power code from multiple-taps or turn off a switch. Our method helps people do the same thing with a smart phone, if they are away from home.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.5
• /
• pp.499-506
• /
• 2019

This paper is concerned with the operating stability of 7kW inverter using SIC hybrid module and verifies the validity of the simulation results by comparing the result of the loss equation and the simulation result, Simulation results using Si module and SiC hybrid module are compared to compare switch loss and diode loss. Through the loss equation calculation, the conduction loss of SiC Hybrid module is 168W, switching loss is 9.3W, diode loss is 10.5nW, When compared with the simulation results, similar values were shown. As a result of comparing the simulation results of the Si module and the SiC Hybrid module, The total device loss of the Si module was 246.2W, and the total device loss of the SiC Hybrid module was 189.9W. The loss difference was 56.3W, which was about 0.8W. thereby verifying the reverse recovery characteristics of the SiC SBD. In addition, temperature saturation test was conducted to confirm the stability of SiC Hybrid module and Si module under high temperature saturation, In the case of the Si module, the output power was stopped at 4kW, and the SiC Hybrid module was confirmed to operate at 7kW. Based on this, an efficiency graph and a temperature graph are presented, and the Si module is graphed up to 4kW and the SiC Hybrid module is graphed up to 7kW.