• Journal of IKEEE
• /
• v.27 no.1
• /
• pp.85-92
• /
• 2023

Recently, as the era of the 4th Industrial Revolution approaches, IoT devices that emphasize portability are increasing. At the same time, battery usage is also increasing rapidly. With the rapid increase in battery usage, issues related to battery safety have become inevitable problems and many studies have been conducted. This paper deals with explosion issues caused by swelling among various battery issues, and includes research and development of a system that detects battery swelling by identifying resistance changes. The core technology of this study is to develop a system that frequently detects changes in the resistance of wires drawn on the battery through changes in volume that occur when the battery swelling, and uses the resistance changes to prevent battery explosion. In addition, through pattern analysis, it was analyzed how the wire should be constructed to cause a lot of resistance changes.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.3
• /
• pp.27-34
• /
• 2017

We investigated the feasibility of parylene F usage as an intermediate layer between a polydimethylsiloxane (PDMS) substrate and an Au thin-film interconnect as well as the swelling effect of PDMS substrate on the stretchable deformability of an Au thin film. The 150-nm-thick Au film, which was sputtered on a PDMS substrate without a parylene F layer, exhibited an initial resistance of $11.7{\Omega}$ and an overflow of its resistance at a tensile strain of 12.5%. On the other hand, the Au film, which was formed with a 150-nm-thick parylene F layer, revealed an much improved resistance characteristics: $1.21{\Omega}$ as its initial resistance and $246{\Omega}$ at its 30% elongation state. With swelling of PDMS substrate, the resistance of an Au film substantially decreased to $14.4{\Omega}$ at 30% tensile strain.

• Nuclear Engineering and Technology
• /
• v.55 no.2
• /
• pp.555-565
• /
• 2023

Despite many advantages as structural materials, austenitic stainless steels (SSs) have been avoided in many next generation nuclear systems due to poor void swelling resistance. In this paper, we report the results of heavy ion irradiation to the recently developed advanced radiation resistant austenitic SS (ARES-6P) with nanosized NbC precipitates. Heavy ion irradiation was performed at high temperatures (500 ℃ and 575 ℃) to the damage level of ~200 displacement per atom (dpa). The measured void swelling of ARES-6P was 2-3%, which was considerably less compared to commercial 316 SS and comparable to ferritic martensitic steels. In addition, increment of hardness measured by nano-indentation was much smaller for ARES-6P compared to 316 SS. Though some nanosized NbC precipitates were dissociated under relatively high dose rate (~5.0 × 10^-4 dpa/s), sufficient number of NbC precipitates remained to act as sink sites for the point defects, resulting in such superior radiation resistance.

• Textile Coloration and Finishing
• /
• v.23 no.2
• /
• pp.118-130
• /
• 2011

In this study, hydrophilic polyurethane (PU) was synthesized by one shot process to get good non-swelling effect and to keep high breathability using reactive silicone oil of mono terminal and bi-terminal types. We also blended non reactive silicone oil with pure hydrophilic PU to compare non-swelling effect and breathability with hydrophilic PU synthesized by the two types of reactive silicone oils. The hydrophilic films were analyzed by nuclear magnetic resonance (NMR) spectroscopy, scanning electron microscope (SEM), Fourier transform infrared (FT-IR) spectroscopy, X-ray photo electron (XPS) spectroscopy, energy dispersive spectrometry (EDS), breathability, waterproofness, tensile strength, contact angle and swelling effect. The results showed that the film made by hydrophilic PU which was synthesized with mono terminal type silicone oil provided good non-swelling effect and acceptable moisture permeability due to the modified surface properties.

• Nuclear Engineering and Technology
• /
• v.56 no.10
• /
• pp.4115-4126
• /
• 2024

The swelling behavior of ferritic/martensitic steels (FC92-B/-N, HT9, and Gr.92) was investigated following 3.5 MeV Fe⁺⁺ ion irradiation. Tested alloys were helium-pre-implanted up to the peak contents of 120 and 240 appm with He/dpa ratio of 1 appm/dpa at room temperature and then exposed to self-ion beam to the peak damage conditions of 120 and 240 dpa at 475 ℃. Field-emission transmission electron microscopy was used to characterize the cavity evolution. FC92-B exhibited the highest resistance to swelling among the irradiated alloys. The final volumetric swelling of FC92-B reached 1.3 % at 70 dpa and 2.9 % at 140 dpa. On the other hand, HT9 exhibited the highest swelling, reaching 7.4 % at 140 dpa. Comparing the present swelling results at 140 dpa/140 appm He with swelling data at 280 dpa/280 appm He from our previous study, it was observed that Gr.92 and FC92-N swelled more at 140 dpa/140 appm He than at 280 dpa/280 appm He. This negative correlation between swelling and dose in Gr.92 and FC92-N is primarily attributed to the helium-associated swelling suppression at higher helium concentration of 280 appm. A bimodal cavity size distribution appeared only in Gr.92 and FC92-N at 280 dpa/280 appm. This result demonstrates that the excess amount of helium over 200 appm promoted early-stabilization of new-born cavities, resulting in preferentially enhanced cavity nucleation, while impeding the growth of nucleated cavities. An inhibition in cavity growth possibly led to an extended duration of nucleation-dominant stages, finally suppressing swelling in ion-irradiated Gr.92 and FC92-N alloys.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.3
• /
• pp.3-26
• /
• 1985

The object of this study was to investigate the effects on physical and mechanical properties of wood particle and sawdust board combined with wire net. Conventional forming, press-lam, and veneer comply boards combining one to four wire net sheets were made from wood particle and sawdust with different spacings (8, 10, 12, and 18 Mok) and different wire diameters (0.35, 0.50, and 0.80mm) composing wire net. They were compared and analyzed statistically with specific gravity, thickness swelling, length swelling, bending properties (modulus of rupture, modulus of elasticity, work to proportional limit, and total work), internal bonding strength, and screw holding strength between wood particle and sawdust boards. The results obtained at this study as cording to the discussions might be concluded as follows; 1. In specific gravity, both particle and sawdust boards by press-lam method were higher than by conventional forming and veneer comply method, and the boards containing more wire net sheets also showed higher value. But the wire net spacings(Mok) had no influence on specific gravity. In general, particle board showed higher specific gravity than sawdust board. Veneer comply board showed lowest specific gravity values. 2. Both particle and sawdust boards by press-lam method was slightly lower than by conventional forming and veneer comply method in thickness swelling. The sawdust board containing 8, 12. and 18 Mok wire net showed lower thickness swelling than the corresponding particle board, but both sawdust and particle boards containing the T8 and 10 Mok wire net showed higher and similar thickness swelling. 3. Both particle and sawdust boards containing wire net showed no difference in MOR and MOE of bending. Comply board was the highest and particle board showed slightly higher than sawdust board in MOR and MOE values. 4. In work to proportional limit and total work in bending, both particle and sawdust boards containing thicker wire diameter and more wire net sheets showed higher value. From these facts, it is conceivable that boards with thicker wire diameter and more wire net sheets show increasing resistance against external force. But there was no significant difference between particle and sawdust borads. 5. In resistance against delamination (internal bonding strength), both sawdust and particle boards containing wire net showed lower value than control, and also showed decreasing tendency with more number of wire net sheet composed. Particle board showed higher resistance against delamination than sawdust board. 6. In screw holding strength, sawdust board containing thicker wire diameter and more wire net sheets showed higher value, but particle board by press-lam method was higher than by conventional forming and veneer comply method. Screw holding strength of particle board was higher than that of sawdust board.

• Textile Coloration and Finishing
• /
• v.31 no.3
• /
• pp.177-186
• /
• 2019

In this study, we investigated for synthetic hydrotalcite in chloroprene rubber foam. Experiments were carried out to find the optimum content ratio by controlling the contents of MgO and Hydrotalcite. Swelling test in toluene immersion was made to measure the crosslinking density of CR foams, and the cure properties were investigated with flat die rheometer and Mooney viscosity. The difference of hardness, tensile strength and elongation at break were observed after immersing in 7% NaCl or 21% NaCl solutions for a day and four days. In addition, the volume change and water content remaining in CR foam were measured after immersing NaCl solution. As content of MgO increased, the value of the cure torque tended to increase, but it was almost constant above 2phr of MgO. However, the Mooney viscosity decreased with increasing MgO content. The crosslinking density, determined by the swelling ratio, showed that the CR compound without MgO showed a higher degree of swelling. When the content of hydrotalcite/MgO was 3:2, it was the lowest volume change of CR form. Also, As the content of hydrotalcite decreased, the difference of mechanical properties before and after immersion NaCl solution increased.

• Journal of the Korea Furniture Society
• /
• v.22 no.1
• /
• pp.54-62
• /
• 2011

The metalized wood composites with natural grain of imported Juglans nigra, which was impregnated with low melting alloy were manufactured and evaluated in this study. And the proper manufacturing conditions was also investigated in this study. The low melting alloy with bismuth (Bi) and tin (Sn) which are harmless to humans, was applied to this new composites. The composites showed not only no defects of discoloration, delamination, swelling, and cracking, because of high dimensional stability and low thickness swelling, but also much improved performance such as high bending strength, high hardness, abrasion resistance, high thermal conductivity as floor materials. This study also suggested the proper impregnating condition, such as 10 minutes of the preliminary vacuum time, $186^{\circ}C$ of the heating temperature and 10 minutes of the maintaining pressure time at the pressure of $30kgf/cm^2$. This metalized wood composites showed 7 times higher density than control, great increase in bending strength from $131.8N/mm^2$ to $192.3N/mm^2$, and great increase in hardness from $18.2N/mm^2$ to $90.4N/mm^2$. The composites demonstrated not only high emissivity of 91%, high shilding effectiveness of 92.59∼99.99%, high fire resistance but also great decrease in abrasion depth, water absorption and thickness swelling.

• Elastomers and Composites
• /
• v.51 no.2
• /
• pp.93-98
• /
• 2016

The composites of EVA/EPDM including aluminum trioxide (ATH) as a fire retardant were manufactured for the purpose of improving low temperature property and flame resistance in the rubbery materials. The ratio of EVA to EPDM didn't affect the flame resistance of the rubber composites. The addition of ATH resulted in increase of the flame resistance. In the evaluation of the cold resistance, the increasing EPDM content showed enhancement of cold resistance in the composites due to increasing low Tg EPDM. It was found out that tensile strengths of the composites showed a maximum value at 100 phr of ATH by reinforcing effect, but a minimum value at 200 phr of ATH owing to slippage between the flame retardant by the external stress. In the measurement of solvent resistance in tetrahydrofuran, the increasing ATH content yielded enhancement of solvent resistance by reducing swelling of the composite, and increasing EPDM content also resulted from increase of the solvent resistance by reduction of polarizability as well as increase of crosslink in the composites.

• The Journal of the Korean dental association
• /
• v.52 no.7
• /
• pp.425-431
• /
• 2014

Objectives : The purpose of our study was to evaluate penicillin as a still drug of choice for severe endodontic infection, by analyzing the antimicrobial susceptibilities from endodontic infections with swelling to figure out appropriate antibiotics as empirical treatment. Materials and methods : This study involved 18 patients who attended for emergency treatment because of facial or periapical swelling associated with root canal infections. Identification and antimicrobial susceptibility test of each pathogen were performed by Vitek2 Systems (bioM$\acute{e}$rieux, Marcy l'Etoile, France). Results : The most frequent bacteria was Streptococcus spp.(77%), and the resistance against penicillin was 35% in overall patients, followed by clindamycin and erythromycin (17%), which was much higher than previous studies. Conclusions : In our study, the higher resistance made penicillin alone not to be chosen as the first antibiotic drug for severe endodontic infections. Combinations with other drug, penicillin with wider spectrum of activity, or changing to other antibiotics was considered while remembering the increased risk of resistant microorganism.