• 한국소음진동공학회논문집
• /
• 제23권7호
• /
• pp.617-623
• /
• 2013

Accurate prediction of the radiated noise is important to reduce the noise of the washing machine. It is also necessary to predict the excitation force accurately because excitation force can induce noise. In order to predict the excitation force acting on the washing machine, this paper conducts source identification method by use of phase reference spectrum. In this method, the transfer function between the cabinet and the motor through FEM and the measured response from the surface of the cabinet is used. The analysis of the radiation noise from the identified exciting force has been investigated. The comparison between the predicted SPL and the measured SPL at 1m apart from the front side of the washing machine showed good tendency.

• 청정기술
• /
• 제27권1호
• /
• pp.39-46
• /
• 2021

4 HP, 80 LPM 급 초미세기포수 발생장치를 탑재한 도로 구조물 세척차량을 이용하여 도시 내 아파트 단지 주변 차량 통행이 많은 터널 내 콘크리트 표면과 타일 벽면을 세척하였다. 초미세기포 생성은 대기 중 공기를 2 ~ 3 LPM 으로 기액혼합 자흡펌프로 가압된 공기를 임펠러 회전력을 이용하여 마이크로 크기의 미세기포(fine-bubble)를 생성한다. 생성된 기포를 다단충돌판과 회전 노즐을 통과하면서 평균 직경 크기는 164.5 nm, 6.81 × 107 particles mL-1의 초미세기포(ultrafine bubble)를 생산하였다. 생산된 초미세기포를 함유한 세척수는 압력 150 bar, 토출량 30 LPM 으로 도로 구조물 표면에 흡착된 분진을 고압세척 분사하여 제거하였다. 분석실험은 세척 전과 후로 구분하여 표면에 흡착한 분진을 ISO 8502-3의 표면 오염 측정방법을 적용하였으며, 테이프 흡착으로 분진 입자를 채취하였다. 수집된 테이프는 중량법과 소프트웨어 ImageJ를 적용하여 분진의 무게와 입자 개수에 대한 제거율을 산정하였다. 실험 결과, 타일 벽면 표면에 흡착된 분진 입자 개수는 세척 전과 후로 각각 3,063 ± 218 particles mL-1, 20 ± 5 particles mL-1, 중량은 580 ± 82 mg, 13 ± 4 mg 으로 나타났다. 콘크리트 구조물 표면에서의 입자개수는 세척 전과 후로 각각 8,105 ± 1,738 particles mL-1, 39 ± 6 particles mL-1이었으며, 중량은 1,448 ± 190 mg, 118 ± 32 mg으로 나타났다.

• 대한치과교정학회지
• /
• 제26권5호
• /
• pp.497-507
• /
• 1996

산부식된 법랑질표면의 오염은 브라켓의 레진 접착력에 영향을 미친다고 보고되어 왔다. 이 연구의 목적은 인산액이 법랑질과 반응하여 수용성염 및 불수용성염을 형성하는 경우와 부식표면이 타액오염된 경우에, 이의 수세시간이 브라켓의 레진접착 전단결합강도에 미치는 영향을 관찰하기 위하여 시행되었다. 치과 교정치료를 목적으로 발거된 총 234개의 상하악 소구치를 대상으로 $37\%$ 인산액으로 60초간 부식한 군, $20\%$ 인산액으로 50초간 부식 한 군, $37\%$ 인산액으로 60초간 부식 하고 타액오염시킨 군으로 나누고, 인산부식군은 각각 0초, 5초, 10초, 20초간 수세하고, 타액오염 군은 0초, 20초,30초 수세하거나, 재부식후 5초, 10초, 20초간 수세한후 레진접착제로 브라켓을 접착하였다. 5각군의 법랑질표면을 주사전자현미경과으로 검경하고, 전단결합강도를 측정하여 비교검토한 결과 다음의 결과를 얻었다. 1) 산부식후 수세를 하지않으면 레진접착제의 전단결합강도가 현저히 감소 하였다. 2) $37\%$ 인산부식액으로 부식시키고 5초, 10초, 및 20초간 수세한후의 접착레진 전단결합강도 사이에는 차이가 없었다. 3) $20\%$ 인산액으로 부식시키고 5초, 10초, 및 20초간 수세한 후의 전단결합강도사이에는 차이가 없었으나, 5초간 수세후의 전단결합강도는 측정치의 변이가 매우컸다. 4) 부식후 타액으로 오염된 법랑질 표면은 5초, 20초간 및 30초간 수세후 및 재부식 한 후의 브라켓접착레진의 전단결합강도사이에 차이가 없었으나, 5초간 수세만한 군의 전단결합강도는 변이가 매우컸다. 이상의 결과에 의하면 수용성 염이 생성되는 농도의 인산액으로 부식하고 5초간 수세후 불수용성 염이 생성되는 농도의 인산액으로 10초간 수세후에, 그리고 타액오염된 부식표면을 재부식없이 20초간 수세후에 브라켓을 접착하면 임상적으로 유용한 부라켓 접착레진의 전단 결합강도를 얻을수 있을 것으로 추정된다.

• Journal of Biosystems Engineering
• /
• 제34권3호
• /
• pp.167-174
• /
• 2009

This study was conducted to develop an agaricus bisporus washing machine which uses compressed air to remove foreign materials attached on the surface of agaricus bisporus. A prototype of the washing machine was constructed, and performance of removing foreign materials was tested. Research results are as follows: 1. Several transferring methods including PE roller rotation, brush roller rotation, PE screw rotation, vibration plate, and belt conveyor were evaluated. Roller, screw, and vibration methods caused damages on the surface of the products, but belt conveyor method caused the least damages. 2. For air jet, a stationary nozzle type and a rotational type were evaluated. The best air jet nozzle was the jet-type nozzle, and the rotational type was more effective than stationary type nozzle. 3. With the conveyer belt, box type moving method and the rotational air jet nozzle, the washing machine showed the best performance when higher than 5.4${\times}$105 Pa of air jet pressure and lower than 0.047 m/s of moving speed was used. Working performance of the system was 650 kg/h, and the damaging rate was 1.2 %.

• Food Science and Biotechnology
• /
• 제14권5호
• /
• pp.645-650
• /
• 2005

To reduce ammonia-like odor in chondroitin sulfate, longnose skate (Rasa rhina) cartilage was processed by washing, autoclaving, and alkali pretreatments. Content of total volatile basic nitrogen (TVB-N), index of ammonia-like odor, of raw skate cartilage without pretreatment was 254 mg/100 g, whereas those of skate cartilage pretreated with washing and autoclaving increased to 630 and 636 mg/100 g, respectively. TVB-N of skate cartilage pretreated with sodium hydroxide sharply decreased to 15 mg/l00 g at optimal condition of 0.12 M and 3.6 volume of NaOH, as determined by surface response methodology of central composite design for optimization. Alkali pretreatment resulted in 97.6% deodorizing. Washing and autoclaving pretreatments had almost no effect on the yield of chondroitin sulfate (approximately 30%), whereas decreased to 16.0% after alkali pretreatment, showing chondroitin sulfate of skate cartilage as chondroitin sulfate C.

• 한국염색가공학회지
• /
• 제33권4호
• /
• pp.238-249
• /
• 2021

In this study, the effect on flame retardancy and various physical properties when TiO₂ was added with a citric acid/phosphate complex acid catalyst together with Pyrovatex CP new (N-methylol dimethylphosphonopropionamide), a phosphorus-based flame retardant, was studied on cotton fibers. SEM-EDS analysis was performed to confirm the surface characteristics and surface element analysis of the flame-retardant treated cotton fibers, and a vertical carbonization test was performed to confirm the char formation capability and flame retardancy according to the phosphoric acid ratio. By comparing the LOI index before and after washing 10 times, the washing durability of the flame retardant solution containing the phosphoric acid catalyst and TiO₂ was tested by LOI index after ten washing cycles. In addition, the influence of the flame-retardant processing on the physical properties were compared including thermogravimetric analysis (TGA), tear strength and whiteness.

• 한국자원식물학회지
• /
• 제18권2호
• /
• pp.216-222
• /
• 2005

복숭아나무 전정 과정에서 발생하는 부산물인 절지의 천연염료로서 이용성을 조사하였다. 복숭아 가지 추출물로 견과 면직물을 염색한 결과 견직물의 표면색은 매염제에 따른 차이가 있는 가운데 무염색포에 비해 색차(${\Delta}$값)가 11.63에서 30.86까지 나타났다. 면직물은 무매염시 17.71에서 황산철 매염시 40.41로 견직물 보다 염색성이 좋은 것으로 나타났다. 매염제에 따라서는 소석회와 가성소다 매염시 a값이 높게 나타났으며, 황산구리와 명반, 식초 매염시는 b값이 높게 나타났다. 세탁을 3회 실시한 뒤 표면색을 조사한 결과 매염제에 따른 차이는 다소 있었으나 전체적으로 무염색구와의 사이에 색차가 줄어든 것으로 나타나 세탁 견뢰도는 다소 약한 것으로 나타났다. pH가 다른 수세액에 의한 수세 및 일광처리 후 표면색의 변화를 조사한 결과처리 전후간에 차이가 적어 pH에 대한 견뢰도 및 일광 견뢰도는 비교적 좋은 것으로 나타났다.

• 한국자원식물학회지
• /
• 제18권1호
• /
• pp.71-77
• /
• 2005

복숭아나무 전정 과정에서 발생하는 부산물인 절지의 천연염료로서 이용성을 조사하였다. 복숭아 가지 추출물로 견과 면직물을 염색한 결과 견직물의 표면색은 매염제에 따른 차이가 있는 가운데 무염색 포에 비해 색차(${\Delta}E$값)가 11.63에서 30.86까지 나타났다. 면직물은 무매염시 17.71에서 황산철 매염시 40.41로 견직물 보다 염색성이 좋은 것으로 나타났다. 매염제에 따라서는 소석회와 가성소다 매염시 a값이 높게 나타났으며, 황산구리와 명반, 식초 매염시는 b값이 높게 나타났다. 세탁을 3회 실시한 뒤 표면색을 조사한 결과 매염제에 따른 차이는 다소 있었으나 전체적으로 무염색구와의 사이에 색차가 줄어든 것으로 나타나 세탁 견뢰도는 다소 약한 것으로 나타났다. pH가 다른 수세액에 의한 수세 및 일광 처리 후 표면색의 변화를 조사한 결과 처리 전후간에 차이가 적어 pH에 대한 견뢰도 및 일광 견뢰도는 비교적 좋은 것으로 나타났다.

• 한국의류학회지
• /
• 제9권2호
• /
• pp.75-84
• /
• 1985

In order to improve dyeing and finishing technology of thin cloth of microfiber(super-fine fiber), the degrees of deep dyeing method, the light fastness, and the washing fastness were investiagted. 1. The thin cloth made of microfiber, $0.15^d\~0.2^d$, was conjugated type and the dyeing degree was lower at 5 to $10\%$ than that of cloth made of common fiber. The cloth of excellent dyeing fastness, light fastness, was developed by increasing the concentration of dye of high quality up to $5\~10\%$. 2. Because refractory rate of microfiber of $0.2^d$ was lower than that of $0.01^d$, the surface refractory rate of $0.2^d$ was lower than that of $0.01^d$ fiber. Therefore the surface of micro-fiber, $0.2^d$, was more rougher than that of $0.01^d$ and it belongs to separate type. 3. The higher degree of dyeing was increased by using dye of microparticle. Also the degree of textile printing was increased by adding urea solution ($20\%$) and glycerine diethylene glycol. 4. Light fastness was very excellent, marked 5 grade. However, washing fastness was 2$\~$3 grade. After dyeing, we could improve to 4 grade, through hot water washing including some organic chlorine solvent. 5. Super microfiber of $0.01^d$ will not be dyed by present dye and dyeing equipment, because right reflection light rate(white light) of fiber surface was too high and the more refraction rate higher the more surface refraction rate will be increased.

• 한국의류학회지
• /
• 제25권1호
• /
• pp.173-182
• /
• 2001

The physical properties and biodegradability of cellulose fabrics, such as cotton and rayon, are expected to vary with textile care. In this study cotton and rayon fabrics were washed repeatedly with detergents, bleaches, or softeners. The changes of physical properties were investigated by measuring retention of breaking strength, shrinkage, handle, and the fiber surface was observed by SEM. The biodegradability of fabrics was also estimated by soil burial test. The results were as follows. Cotton fabrics laundered repeatedly by detergents and bleaches lost virtually no strength. The breaking strength of the rayon fabrics decreased by about 17%∼25% after repeated launderings. Shrinkage in weft direction was much larger than that in warp direction. Bending rigidities of both fabrics decreased remarkably within 10 wash cycles. Shear rigidity in cotton fabrics increased continuously with repeated washing cycles, however, that in rayon fabrics did not show any change as washing went on. Friction coefficient increased in both fabrics after 10 wash cycles, and this is thought to be attributed to the wrinkle, interlocking of hairs, surface damage resulted from repeated washings. In cotton fabrics made of staple yarns, short hairs on the yarn surface entangled together with repeated launderings. This resulted in the continuous increase in % shrinkage, shear rigidity, friction coefficient. Rayon fabrics made of filament yarns, however, did not show this phenomenon. Softener treated fabrics showed the lowest values in bending rigidity, shear rigidity and friction coefficient because the cationic surfactants adsorbed on the fiber surface behaved like lubricants. The biodegradability of fabrics was noticeably affected by the composition of washing solutions. The fabrics washed with detergents and bleaches were decomposed faster than those washed with the others were and the cotton fabrics washed with detergents and softeners hardly degraded. The fabrics soiled with milk were decomposed almost completely and those soiled with Palmitic acid did not degrade greatly.