• Journal of Power System Engineering
• /
• v.14 no.2
• /
• pp.60-64
• /
• 2010

This paper introduces reliability improvement and time saving in eddy current inspection by signal characteristic optimization of multi-coil eddy current array probe. In the past, Multi-coil array probe and single probe were used for the gas turbine rotor surface inspection & defect evaluation. The multi-coil array probe was used for the broad area inspection. But the signal deviations among multi-coil array probe are maximum 28% in commercial probe. This differences were considered to impedance differences among coils, so it is very difficult to evaluate exact defect size. The signal deviations among multi-coil array probe are maximum 28% in commercial probe. So, single coil inspection was used for exact defect sizing. The purpose of this study is to improve signal deviations of multi-coil array probe. The introduced new technology can improves this deviation by adjusting input voltage in each coil. At first, apply same voltage in each coil and collect signal amplitude of each coil. And calculate new input voltage based on signal amplitude of each coil. If the signal amplitude deviation is within 5% among multi-coil array probe, the signal amplitude of multi-coil array probe is reliable. The proposed technology gives 2% signal deviation among multi-coil array probe. The proposed new technology gives reliability improvement and inspection time saving in eddy current inspection.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2006.06a
• /
• pp.117-121
• /
• 2006

Virgin bleached kraft pulp, CPO (computer printout) and white ledgers are main raw materials used in tissue mills. The utilization rate of recycled fibers and virgin pulp in South Korea tissue industry are 90% and 10%, respectively. To improve brightness of printing grades the use of 'fluorescent whitening agents (FWAs)' or 'optical brightening agents (OBAs)' has been increased. When recycling these papers for tissue production, it is unavoidable that FWAs contained in recycled papers flow into tissue production lines and remain in the products. And this draws great attention from the public. This study was carried out to develop a technology for the removal of fluorescent whitening agents from recycled fibers. Enzymatic removal of FWAs was evaluated as a method to remove FWAs from the recycled fiber. The ${\alpha}-amylase$ that degrades starched used for surface sizing of fine papers and contained substantial condition is needed to prevent the re-adsorption of FWAs on fibers. The temperature of pulp suspension was another important factor affecting on FWA removal. The higher the temperature, the greater the efficiency of removing FWAs was obtained. Optimum pH and temperature for the effective removal of FWAs were suggested to be pH 8.5 and $65^{\circ}C$, respectively. The enzymatic removal of FWAs showed a great synergistic effect when proper control in pH and temperature was made.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.9 no.3
• /
• pp.1-7
• /
• 1985

연구의 목적은 의류생산에 있어서 동양(Oriental women)과 서양여자(Caucasian women: U.S.A)의 인체계측에 의한 치수의 비교를 하였다. 연구자료는 동양여자 100명과 서양여자 970명의 자료로 비교하였다. 동양여자의 인체계측치는 1981년 4월 일본에서 필자에 의해 수집되고 서양여자의 인체계측치는 1976년 11월부터 1977년 2월 미국(U.S.A by the Quartermaster Corps of the United States Army)에서 인체계측을 한 자료이다. 동양과 서양여자의 인체계측치 중에서 각각 32항목을 선출하여 비교된 것은 높이항목과 길이항목(height-related measurements; height and length), 나비항특(surface measurements; breadth and depth) , 둘레항목(measurement of circumference)이다. 32항목을 평균치의 t-test로 동양인과 서양인을 비교한 결과, 모든 항목에서 P<.001 수준에서 유의한 차를 보였다. 그 중에서 머리둘레, 목둘레, 손목둘레, 팔굼치둘레, 손바닥둘레의 항목에서는 동양인이 서양인에 비해서 큰 값을 나타냈다. 그 외에 27개 항목은 동양인이 전부 높거나, 길거나, 또는 큰 값을 나타냈다. 표준편차에서 보이는 바와 같이 서양인자가 동양여자보다 크고, 특히 높이 항목, 길이항목(height-related measurements)이 더 높거나 길다. 이러한 결과로서 동양과 서양여자의 인종적인 측면에서, 다양한 의류생산에 있어서 고려해야 할 것 같다. 이 동양과 서양여자의 인체계측비교에 중요한 요점을 두고 연구한 것은 의류생산과정에 있어서, size설정, 보다 미적인 design, 의복구성을 위한 등등에 고려되겠으나, 특히 미국과 같은 대량생산국에서 동양과의 무역(import or export)에 있어서 중요하게 고려가 될것이며, 나날이 발전하는 우리나라의 의류무역에도 고려되리라 본다. 뒤에 recommendations for future research에서 말한 바와 같이 서양과 한국여자의 입체계측비교를 하며 우리나라의 의류무역(수출)에 도움이 되었으면 한다.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.32 no.2
• /
• pp.340-347
• /
• 2008

A prototype of 3D clothing design system with a direct pattern development function was suggested, reflecting intuitive design functions and design modifications while considering the fit of clothing patterns with the 3D human body in the virtual 3D space. The research method was as follows. Clothing models were created using a 3D design tool, 3ds max on the surface of 3D human body model made by scanning an actual human body. 3D illustrations were completed by revising the fit and sizing of the human body and clothing models. 2D T-shirt pattern was produced 3D illustrations using from a 3D scanning data modeling solution RapidForm 2004, a 2D conversion program for 3D data called 2C-AN, and Yuka CAD. As a result, the following conclusions were made. The fit of the clothing and human body can be adjusted by reflecting individual body figure characteristics and 3D illustrations over the actual 3D body model. Furthermore, intuitive design support functions were intensified overcoming the weak point of existing 3D clothing design system by developing the direct clothing design in the virtual 3D space. 3D illustration design modifications can be directly reflected on clothing patterns from 3D illustrations by 3D clothing design system developed in this study.

• Journal of the Korean Society of Industry Convergence
• /
• v.24 no.1
• /
• pp.31-43
• /
• 2021

In this study, approximate design optimization using various meta-models was performed for the structural design of active type deck support frame. The active type deck support frame was newly developed to facilitate both transportation and installation of 20,000 ton class offshore plant topside. Structural analysis was carried out using the finite element method to evaluate the strength performance of the active type deck support frame in its initial design stage. In the structural analysis, the strength performances were evaluated for various design load conditions that were regulated in ship classification organization. The approximate optimum design problem based on meta-model was formulated such that thickness sizing variables of main structure members were determined by achieving the minimum weight of the active type deck support frame subject to the strength performance constraints. The meta-models used in the approximate design optimization were response surface method, Kriging model, and Chebyshev orthogonal polynomials. The results from approximate design optimization were compared to actual non-approximate design optimization. The Chebyshev orthogonal polynomials among the meta-models used in the approximate design optimization represented the most pertinent optimum design results for the structure design of the active type deck support frame.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.5
• /
• pp.407-415
• /
• 2008

The tubes in heat exchanger are typically made from copper alloy, stainless steel, carbon steel, titanium alloy material. type-439 ferritic stainless steel is ferromagnetic material, and furnish higher heat transfer rates than austenitic stainless steels and higher resistance to corrosion-induced flaws. Ferritic stainless steel can typically be found in low-pressure(LP) feedwater heaters and moisture separator reheaters(MSRs). LP feedwater heaters generally utilize thin wall type-439 stainless steel tubing, whereas MSRs typically employ a heavier wall tubing with integral fins. Service-induced damage can occur on the OD(outside diameter) surface of type-439 ferritic stainless steel tubing which is employed for MSRs tubing, and the most typical damage mechanism is vibration-induced tube-to-TSP(tube support plate) wear and fatigue cracking. The wear has been reported that occurs mainly on the OD surface. Accordingly, in this study, we have evaluated the flaw sizing capability of magnetic saturation eddy current technique using magnetic saturation probe and flawed specimen.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2001.11a
• /
• pp.7-7
• /
• 2001

The increasing interest in light weight materials coupled to the need for cost -effective processing have combined to create a significant opportunity for aluminum P/M. particularly in the automotive industry in order to reduce fuel emissions and improve fuel economy at affordable prices. Additional potential markets for Al PIM parts include hand tools. Where moving parts against gravity represents a challenge; and office machinery, where reciprocating forces are important. Aluminum PIM adds light weight, high compressibility. low sintering temperatures. easy machinability and good corrosion resistance to all advantages of conventional iron bm;ed P/rv1. Current commercial alloys are pre-mixed of either the AI-Si-Mg or AL-Cu-Mg-Si type and contain 1.5% ethylene bis-stearamide as an internal lubricant. The powder is compacted in closed dies at pressure of 200-500Mpa and sintered in nitrogen at temperatures between $580~630^{\circ}C$ in continuous muffle furnace. For some applications no further processing is required. although most applications require one or more secondary operations such as sizing and finishing. These sccondary operations improve the dimension. properties or appearance of the finished part. Aluminum is often considered difficult to sinter because of the presence of a stable surface oxide film. Removal of the oxide in iron and copper based is usually achieved through the use of reducing atmospheres. such as hydrogen or dissociated ammonia. In aluminum. this occurs in the solid st,lte through the partial reduction of the aluminum by magncsium to form spinel. This exposcs the underlying metal and facilitates sintering. It has recently been shown that < 0.2% Mg is all that is required. It is noteworthy that most aluminum pre-mixes contain at least 0.5% Mg. The sintering of aluminum alloys can be further enhanced by selective microalloying. Just 100ppm pf tin chnnges the liquid phase sintering kinetics of the 2xxx alloys to produce a tensile strength of 375Mpa. an increilse of nearly 20% over the unmodified alloy. The ductility is unnffected. A similar but different effect occurs by the addition of 100 ppm of Pb to 7xxx alloys. The lend changes the wetting characteristics of the sintering liquid which serves to increase the tensile strength to 440 Mpa. a 40% increase over unmodified aIloys. Current research is predominantly aimed at the development of metal matrix composites. which have a high specific modulus. good wear resistance and a tailorable coefficient of thermal expnnsion. By controlling particle clustering and by engineering the ceramic/matrix interface in order to enhance sintering. very attractive properties can be achicved in the ns-sintered state. I\t an ils-sintered density ilpproaching 99%. these new experimental alloys hnve a modulus of 130 Gpa and an ultimate tensile strength of 212 Mpa in the T4 temper. In contest. unreinforcecl aluminum has a modulus of just 70 Gpa.

• Journal of fish pathology
• /
• v.24 no.2
• /
• pp.161-166
• /
• 2011

The metacercariae of Clinostomum complanatum (Rudolphi, 1814) were isolated in the whole body muscle of wild freshwater fish, spotted barbel gudgeon (Squalidus multimaculatus Rosoya et Jeon) from the local river in Yeongdeok, Gyeongsangbuk-do, Korea. The infected fish with bumpy body surface by "yellow grub" showed erratic swimming behavior and some fish were died. The isolated excysted metacercariae were tongue shaped and 2.85~5.89 mm ${\times}$ 0.8~1.99 mm in size. 1~98 metacercariae were isolated in individual fish and mean infection intensity was 25. All examined adult spotted barbel gudgeon sizing 7 cm in body length were infected. This is the first report of disease outbreak and mortality caused by C. complanatum infection in wild freshwater fish in Korea.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.18 no.6
• /
• pp.455-463
• /
• 1998

RCCA(rod cluster control assembly) End-Tip suffers from neutron irradiation and constant vibration due to high-speed internal flow of primary coolant during plant operation. Such operating conditions cause the RCCA end-tip crackings around tile circumferential weldment of the end-tip, and in some cases, the defective end-tips were completly broken loose. However, no reliable inspection techniques for end-tip crackings were developed in the past, although some techniques exist for inspecting RCCA control rod wears. Therefore, NDE group at KEPRI has developed an ECT technique for the detection and the sizing of the end-tip crackings. The technique uses a specially designed surface-riding probe that can detect size of circumferential crackings with an accuracy of ${\pm}5.31%$ RMS error. This paper describes the ECT instrumentation including the ECT probes, calibration bars, as well as technical approaches.

• Journal of Convergence for Information Technology
• /
• v.11 no.2
• /
• pp.98-106
• /
• 2021

The paper deals with comparative study on sensitivity analysis using various methods regarding to design of experiments for structure design of an active type DSF (Deck support frame) that was developed for float-over installation of offshore plant. The thickness sizing variables of structure member of the active type DSF were considered the design factors. The output responses were defined from the weight and the strength performances. Various methods such as orthogonal array design, Box-Behnken design, and Latin hypercube design were applied to the comparative study. In order to evaluate the approximation performance of the design space exploration according to the design of experiments, response surface method was generated for each design of experiment, and the accuracy characteristics of the approximation were reviewed. The design enhancement results such as numerical costs, weight minimization, etc. via the design of experiment methods were compared to the results of the best design. The orthogonal array design method represented the most improved results for the structure design of the active type DSF.