• Proceedings of the KSRS Conference
• /
• 2002.10a
• /
• pp.312-316
• /
• 2002

Satellite radar interferometry data shows a strong coherent signal on oyster sea farms where artificial structures installed on the bottom. We obtained 21 highly coherent interferograms from eleven JERS-1 SAR data sets despite of large orbital baseline (~2 km) or large temporal baseline (~l year). The phases observed in sea farms are probably induced by double bouncing on sea surface, and consequently reveal a tide height variation. To restore the absolute sea level changes we counted the number of wrapping by exploiting the intensity of backscattering. Backscattering intensity is closely correlated with the change in water surface height, while interferometry gives the detailed variation within the limit of 2$\pi$ (or 15.3 cm). Comparing the radar measurements with the tide gauge records yielded a correlation coefficient of 0.96 and an ms error of 6.0 cm. The results demostrate that radar interferometry is promising to measure sea level.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.05a
• /
• pp.353-353
• /
• 2012

음극방식법은 가혹한 해수 환경에 노출된 항만 및 해양구조물 등의 부식을 방지함에 있어 매우 유용한 방식법이다. 여기서는 이러한 음극방식 응용 원리에 의해 무한한 자원인 해수를 이용하여 환경 친화적인 코팅막 제작-시도를 하였다. 즉, 본 연구에서는 해수 환경 중 선박 및 해양구조물 등에 주로 사용되는 강재를 기판으로 하여 양극 조건 및 인가 전류밀도를 달리하여 코팅막을 제작하였으며, 조건에 따라 제작된 코팅막을 SEM, EDS, XRD를 통해 조성원소 및 결정구조를 분석하였다. 또한 밀착성 및 내식성 평가를 통해 실용 코팅막으로써의 한계를 보완한 코팅막 제작 프로세스의 기초 설계 지침을 제시하고자 하였다.

• 한국해양학회지
• /
• v.11 no.2
• /
• pp.89-95
• /
• 1976

Some factors of seawater such as water temperature, salinity, pH, dissolved oxygen and asturation of dissolved oxygen were determined in 5 meters intervals from surface to bottom at 11 stations in Yeongil Bay of Korea during late October 1973. Distribution pattern of water masses in Yeongil Bay during the period seemed to be heterogeneous as dividing into two parts of surface and bottom. Water temperature, pH, dissolved oxygen and saturation of dissolved oxygen of surface water mass showed higher values and salinity of the mass showed lower values than those factors of bottom water mass. Surface water mass might be originated from Tsushima current during summer season and bottom water mass from cold body of East Sea of Korea which seemed to extend to coastal zone during winter season. Land water discharge from Hyeongsan River into the Bay is considered as a minor factor playing slight role in the water mass composition of the area.

• Journal of Surface Science and Engineering
• /
• v.46 no.3
• /
• pp.120-125
• /
• 2013

This investigation was to identify the electrochemical corrosion protection conditions to minimize the cavitation damage by generating hydrogen gas with the means of hydrogen overvoltage before the impact pressure of the cavity is transferred to the surface. The hybrid potentiostatic test method is designed to evaluate a complexed cavitation and electrochemical characteristic for ALBC3 alloy that is diverse and its broad applications fields in marine industry. The surface observation showed that neither the cavitation damage nor the electrochemical damage by the hydrogen gas generation occurred in the potential of -2.6 V under the cavitation environment. In the potentiostatic experiments under the cavitation environment, the cavities were reflected or cancelled out by the collision of the cavities with the hydrogen gas generated by the hydrogen overvoltage.

• Corrosion Science and Technology
• /
• v.12 no.5
• /
• pp.233-238
• /
• 2013

In the case of casting materials or ductile materials for marine equipment, it is common to employ a surface modification for achieving cost reduction and improvement in strength. In particular, aluminium bronze ALBC3 exhibits excellent corrosion resistance, and thus widely used for marine application. However, application of the material under high-velocity seawater flow may induce electrochemical corrosion damage and physical damage such as cavitation erosion, leading to shorter service life of equipment. In this study, surface modification was carried out on ALBC3 alloy for different shot peening stand-off distances, and the physical hardness and electrochemical characteristics before and after modification were investigated. The results in each case showed the hardness increase in comparison with non-peened specimen, and the maximum hardness improvement(50 %) was found in 10 cm of shot-peening stand-off distance. It is observed that the electrochemical characteristics were irrelevant to application of shot peening.

• Fisheries and Aquatic Sciences
• /
• v.3 no.2
• /
• pp.143-150
• /
• 2000

Assuming that summer surface waters in the South Sea (northern East China Sea) are formed mostly by a mixing of three source water (Changjiang Discharge Water; Kuroshio Water and Yellow Sea Surface Water) we apply optimum multiparameter (OMP) analysis to calculate the mixing ratio of each source water to a given surface water. Since OMP requires more parameters than the number of water types (three in this study), we utilize two radium isotopes of dissolved $^{226}Ra\;and\;^{228}Ra$ along with temperature and salinity. Parameter values of each source water are deduced from in situ and historical data. Results with three source of waters on the surface waters are quite promising with less than $1\%$ of unanswered portions. Results not only reproduce the measured temperature and salinity faithfully but also discern the water masses of similar T and S according to their source water mixing. Extending OMP analysis to a whole water column obviously requires more parameters because more source waters are involved in the water mass formation. Original OMP routine utilized dissolved oxygen and nutrients. However, they seem to be perturbed too much by biological activities in the case of shallow waters. We discussed the use of other potential parameters. Also the benefit of parameter substitution is briefly introduced for the future OMP application on shallow waters.

• Journal of Surface Science and Engineering
• /
• v.48 no.6
• /
• pp.343-348
• /
• 2015

In this paper, arc Zn thermal spray coating was carried out on the SS400 steel, and then various electrochemical characteristics and surface damage behavior of Zn thermal spray coating layer were analyzed. As the results, the potential of Zn thermal spray coating layer presented driving voltage above 300 mV compare to that of SS400 steel. The passivity characteristic in anodic polarization curve was not presented. It was adequate to as sacrificial anode material. In the surface damage after galvanostatic experiments, uniform corrosion tendency of Zn thermal spray coating layer was clearly observed with acceleration of the dissolution reaction. In conclusion, Zn thermal spray coating could be determined to represent the corrosion protection effect by stable sacrificial anodic cathodic protection method in seawater because it had sufficient driving voltage and uniform corrosion damage tendency for the SS400 steel.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.2
• /
• pp.113-119
• /
• 2000

An experimental study has been carried out in order to investigate on a particle deposition on a circular cylinder surface. The present study is focused on the particulate fouling occurring in a heat exchanger for a seawater desalinization, in a laminar flow over circular cylindrical tubes. The objective is to investigate how NaCl concentration influences the $SiO2$ particle deposition on the surface of a glass circular cylinder. The NaCl concentration was changed from 0 g/L to 40 g/L. As the experimental results of $SiO2$ particle which is deposited on the glass circular cylinder surface showed, particle deposition rate per unit time increases rapidly with the increase of NaCl concentration between 0 g/L and 15 g/L. After the maximum of particle deposition rate was found at the NaCl concentration of 15 g/L, particle deposition rate remains unchanged or decreases gradually with the NaCl concentration from 15 g/L to 40 g/L. Also the $SiO2$ deposition rate of particles does not have serious variations with the position at present glass surface.

• Corrosion Science and Technology
• /
• v.21 no.4
• /
• pp.290-299
• /
• 2022

Anodizing is an electrochemical surface treatment method conferring corrosion resistance and durability by forming a thick anodization film on the metal surface. Aluminum has a long service life and high thermal conductivity and formability, as well as excellent corrosion resistance. Aluminum 3003 alloy has improved formability, strength, and corrosion resistance due to the addition of a small amount of manganese. However, corrosion occurs in seawater and environments polluted with corrosion-inducing substances, which reduce corrosion resistance. Therefore, it is necessary to artificially form a thick anodized film to improve corrosion resistance. In this study, the anodization treatment time was 4 minutes, and voltages of 10 V, 20 V, 30 V, 40 V, 50 V, 60 V, 70 V, 80 V, 90 V, and 100 V were applied. The thickness and pore size of the oxide film increased according to the applied voltage. A barrier film was formed under voltage conditions from 10 V to 50 V, and a porous film was formed under voltage conditions from 60 V to 100 V. After anodizing, coating was applied. Wettability and corrosion resistance were observed before and after coating according to the surface shape and thickness of the oxide film.

• Journal of the Mineralogical Society of Korea
• /
• v.28 no.1
• /
• pp.9-16
• /
• 2015

A mineralogical analysis on the factors affecting the luster of pearls was carried out using gravity measurement, optical microscope observation, X-ray diffraction analysis, and scanning electron microscopy. We divided the seawater cultured pearls from Tongyeong into the following four types based on luster and shape; good luster and round (LR), lackluster and round (LLR), lackluster and baroque (LLB), and lackluster and two nucleus (LTN) pearls. Pearls with high-quality luster had slightly lower specific gravity as compared to pearls with low-quality luster, but both these types of pearls are within the specific gravity range of commercial pearls. Regarding the cross-sectional thickness of the mother-of-pearl layer, LR pearls showed a uniform thickness of about 0.3 mm in average. On the other hand, LLR pearls were characterized by relatively thinner, but uniform thickness. LTN and LLB pearls showed a tendency of significantly large variation in thickness even within a single pearl. For the surface of pearls, pearls with high-quality luster showed narrower and clearer growth lines of aragonite crystals as compared to pearls with low-quality luster. Pearls with high-quality luster were characterized by fewer aragonite crystal lattice defects as compared to pearls with low-quality luster, and the former showed parallel arrangement, thinner thickness, and less difference in thickness on the surface and inside. If a pearl has a prismatic layer, it is composed of aragonite with calcite in the prismatic and nacreous layer, and calcite content is very high in the lackluster pearl. Pearls without a prismatic layer were devoid of calcite irrespective of their quality of luster, and were composed of aragonite.