• 한국재료학회지
• /
• 제26권3호
• /
• pp.154-159
• /
• 2016

A roll-bonding process was applied to fabricate an AA1050/AZ91/AA1050 laminate complex sheet. Two AA1050 and one AZ91 magnesium sheets of 2 mm thickness, 30 mm width and 200 mm length were stacked up after surface treatment that included degreasing and wire brushing; material was then reduced to a thickness of 3 mm by one-pass cold rolling. The laminate sheet bonded by the rolling was further reduced to 2 mm in thickness by conventional rolling. The rolling was performed at 623K without lubricant using a 2-high mill with a roll diameter of 210 mm. The rolling speed was 15.9 m/min. The AA1050/AZ91/AA1050 laminate complex sheet fabricated by roll bonding was then annealed at 373~573K for 0.5h. The microstructure of the complex sheets was revealed by electron back scatter diffraction (EBSD) measurement; the mechanical properties were investigated by tensile testing and hardness testing. The strength of the complex sheet was found to increase by 11 % and the tensile elongation decreased by 7%, compared to those values of the starting material. In addition, the hardness of the AZ91 Mg region was slightly higher than those of the AA1050 regions. Both AA1050 and AZ91 showed a typical deformation structure in which the grains were elongated in the rolling direction; however, the mis-orientation distribution of grain boundaries varied greatly between the two materials.

• 수산해양기술연구
• /
• 제14권2호
• /
• pp.69-78
• /
• 1978

알루미나이징강에 대하여 초기마모영역에서 rolling-sliding 마모시험을 한 결과를 요약하면 다음과 같다. 1) 2차 확산재의 내마모성이 가장 우수하고 처녀재에 비하여 저응력 레벨에서 약 18%, 고응력에서 약 40%의 마모감소를 나타낸다. 2) 2차 확산재는 피복층과 합금층 경계부근의 공공생성으로 인하여 예상보다 내마모성이 낮다. 3) 알루미나이징강의 rolling-sliding 접촉에 의한 마모파양의 형태는 spalling 이며 spalling crack은 합금속의 경계부근에서 발생한다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제36권2호
• /
• pp.276-285
• /
• 2012

본 연구목적은 열간압연용 런-아웃 테이블 롤러 표면의 기계적 성질을 개선하기 위해 다공질 자용성 합금으로 피복하는 방법을 개발하는 것이다. 열간압연에서 런-아웃 테이블의 롤러 내구성을 높이기 위해서는 고온에서 롤러표면의 경도를 높게 유지해야 하고, 내마모성, 내식성, 내열성, 내소부성 및 내응착성의 향상을 유지하여야 한다. 또한, 고온의 열연 강판을 안정적으로 이송할 수 있도록 하기 위해서는 롤러표면에 적절한 마찰계수를 유지하도록 하여야 하고, 롤러와 강판 사이에 미끄럼 발생이 없어야 한다. 본 연구에서는 자용성 합금에 텅스텐카바이드를 첨가시켜 서메트화하여 롤러의 내마모성을 증대시켰고, 미세 철분말을 롤러표면에 피복하여 다공질을 만들어 마찰계수를 높이고 붙잡음성을 향상시켰다. 그 결과, Ni-Cr 피복 롤러에 비하여 다공질 자용성 합금 피복 롤러는 피복층에 철분이 5 ~ 10 wt%로 많이 함유되어 재용융 공정에서 전기로로 가열하여 일부분만 합금화되고 나머지는 산화 및 용해에 의해 탈락되어 다공질로 나타나 강판과의 붙잡음성을 향상시켰다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.826-831
• /
• 2004

In this study. problems caused during production process of stainless steel carbody are investigated and solutions are found out. Roll forming process to make complex shape is introduced and surface crack on high strength stainless steel plate is investigated. Also, surface indentation is discussed and the effect of welding condition is clarified. Insulated tip to reduce the indentation is recommended for improvement of surface smoothness. Lastly. corrosion of welded joint is discussed and the effects of material, stress and environment are investigated.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1998년도 창립기념 춘계학술대회 논문집
• /
• pp.315-322
• /
• 1998

A two dimensional elasto-plastic finite element program taking into account contact between crack surfaces if developed in order to analyze subsurface cracking in rolling contact. But the friction between upper and lower surface of the crack is not considered. Under the assumptions of small deformation and small displacement, the incremental theory of plasticity is used to describe plastic deformation. J-integral is computed as the applied Hertzian load slides over the surface with friction. J-integral is correlated with wear rate of the rail. The propagation rate of the right tip of the surface crack is fast by 45% than that of the left side.

• 대한조선학회지
• /
• 제14권3호
• /
• pp.13-22
• /
• 1977

The hydrodynamic forces acting on a forced oscillating 2-dimensional cylinder on a free surface of a fluid of a finite depth are calculated by distributing singularities on the immersed body surface. And the Haskind-Newman relation in a fluid of a finite depth is derived. The wave exciting force of the cylinder to an oscillation is also calculated by using the above relation. The method is applied to a circular cylinder swaying in a water of finite depth, and then, to a rectangular cylinder heaving, swaying, and rolling. The results of above cases give a good agreement with those by earlier investigators such as Bai, Keil, and Yeung. Also, this method is applied to a Lewis form cylinder with a half beam-to-draft ratio of 1.0 and a sectional area coefficient of 0.941, and to a bulbous section cylinder which is hard to represent by a mapping function. The results reveal that the hydrodynamic forces in heave increase as the depth of a water decrease, but in sway or roll, the tendency of the hydrodynamic forces is difficult to say in a few words. The exciting force to heave for a bulbous section cylinder becomes zero at two frequencies. The added mass moment of inertia for roll is seemed to mainly depend on the sectional shape than the water depth.

• 소성∙가공
• /
• 제15권8호
• /
• pp.550-555
• /
• 2006

In this study, effects of forming angle and friction coefficient on a initiation of the Mannesmann hole defect were analyzed by using a response surface method. The maximum effective plastic strain at center point of specimen is utilized for the prediction of the starting point of crack occurrence, which is suggested by the comparison of integrals of four different ductile fracture models between the histories of the effective plastic strain at center point. It was revealed that the principal stress at the center is the dominant element to the increase of the effective plastic strain. It was also verified by the simulation results from the comparison of experiment and simulation. It is provided that the forming angle of 25 degrees and the spreading angle of 1 degree can be a proper design condition without an occurrence of internal hole defect and an excessive slip.

• 한국표면공학회지
• /
• 제45권4호
• /
• pp.155-161
• /
• 2012

Magnesium alloys of AZ31, AZ31 + (0.5, 1, 1.5)wt.% CaO were cast, hot rolled, and oxidized between 450 and $650^{\circ}C$ in atmospheric air. The added CaO enabled to cast the AZ31 alloy in air. It decomposed and precipitated along the grain boundaries of the AZ31 alloy as $Al_2Ca$. The more the amount of CaO was, the more $Al_2Ca$ formed. The oxidation limit was about $450^{\circ}C$ for the AZ31 alloy. But, It increased to $650^{\circ}C$ in the CaO-added alloys. Hot rolling destroyed the precipitates that formed along the grain boundaries of the AZ31 alloy. During oxidation, MgO oxide scales that incorporated CaO formed at the outer surface of the formed oxide layer.

• 한국재료학회지
• /
• 제28권8호
• /
• pp.435-439
• /
• 2018

MA Al alloys are examined to determine the effects of alloying of Mg and Cu and rolling on tensile deformation behavior at 748 K over a wide strain rate range($10^{-4}-10^3/s$). A powder metallurgy aluminum alloy produced from mechanically alloyed pure Al powder exhibits only a small elongation-to-failure(${\varepsilon}_f$ < ~50%) in high temperature(748 K) tensile deformation at high strain rates(${\acute{\varepsilon}}=1-10^2/s$). ${\varepsilon}_f$ in MA Al-0.5~4.0Mg alloys increases slightly with Mg content(${\varepsilon}_f={\sim}140%$ at 4 mass%). Combined addition of Mg and Cu(MA Al-1.5%Mg-4.0%Cu) is very effective for the occurrence of superplasticity(${\varepsilon}_f$ > 500%). Warm-rolling(at 393-492 K) tends to raise ${\varepsilon}_f$. Lowering the rolling-temperature is effective for increasing the ductility. The effect is rather weak in MA pure Al and MA Al-Mg alloys, but much larger in the MA Al-1.5%Mg-4.0%Cu alloy. Additions of Mg and Cu and warm-rolling of the alloy cause a remarkable reduction in the logarithm of the peak flow stress at low strain rates (${\acute{\varepsilon}}$< ~1/s) and sharpening of microstructure and smoothening of grain boundaries. Additions of Mg and Cu make the strain rate sensitivity(the m value) larger at high strain rates, and the warm-rolling may make the grain boundary sliding easier with less cavitation. Grain boundary facets are observed on the fracture surface when ${\varepsilon}_f$ is large, indicating the operation of grain boundary sliding to a large extent during superplastic deformation.

• 한국산학기술학회논문지
• /
• 제12권3호
• /
• pp.1085-1090
• /
• 2011

철도차량의 안전성을 확보하기위해서는 견인성능 및 속도의 변동성을 고려하여 감속기의 피로해석에 관한 연구를 수행하는 것이 중요하다. 본 논문은 고속철도차량 감속기 기어의 변동하중하에서 피로파괴에 대하여 준정적 유한요소해석과 선형 Miner's Rule에 의한 내구성해석을 수행하였다. 해석을 위한 변동하중이력은 열차견인성능곡선과 상업운전조건에서 운전선도를 기초로 MSC.ADAMS의 동역학 해석에 의하여 구축하였다. 또한 감속기 피로수명은 기어표면의 침탄부 효과를 고려한 유한요소모델을 사용하여 변형률-수명접근법에 의하여 예측하였다. 해석결과로부터 급출발에 의한 빈번한 높은 기동토크와 정차역수의 증가는 철도차량 감속기 기어수명을 감소시킴을 알 수 있었다.