• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.2
• /
• pp.49-57
• /
• 2001

This study was performed to identify the effect of calendering variables on the properties of coated paper such as sheet gloss, surface roughness, opacity, etc. The effect of calendering variables including the number of nips, pressure, machine speed and moisture content on the properties of coated paper was investigated. The calender was installed with two steel rolls and one cotton-made roll. With this calender, the coated sheets were passed through the calender from 1 to 4 times, applying the linear pressure on calender rolls, 5 through 100kg/cm and operating the machine speed 3 to 12m/min. Also, the moisture content of coated sheet was varied about 5 and 10%. It was found that sheet gloss and surface roughness of coated paper was increased with increasing the number of passing nips, linear roll pressure and the moisture content of coated paper. But it was shown that the opacity and brightness of coated paper were decreased under the above conditions due to the blackening. It was also suggested that the soft nip possibly increased the thermoplasticity of coating layer with the heat of steel roll, resulting in the reinforcement of surface properties positively. The sheet gloss and surface roughness of coated paper could be improved by the longer dwell time over the rolls.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.37 no.2 s.110
• /
• pp.70-77
• /
• 2005

For the purpose of developing liner board for water resistant corrugated board in the cold chain system, several types of base paper for corrugated board were purchased from the market and 6 different boards were produced in the mill by applying the chemicals, chosen in the previous studies, on the base paper. Then water-moisture resistance and physical properties of the boards were compared each other. The liner board which is dried at high temperature with pressure by Condebelt (CK paper) showed a superior performance in strength over common liner boards. Strength of the board increased by surface chemical treatment up to $60\%$ of compressive strength and $30\%$ of burst strength. Starch insolubilization with Ammonium Zirconium Carbonate and surface coating with a surface sizing agent and a moisture resistant chemical on CK paper showed the best result. Therefore this method was recommended to produce the outer liner board for water resistant corrugated board.

• Journal of Environmental Science International
• /
• v.31 no.1
• /
• pp.43-50
• /
• 2022

In this paper, lysimeter was installed to analyze the moisture fluctuations on the surface of a forest. The weight of the soil was measured, and the moisture fluctuations were calculated through the difference in weight over time. The amount of dew condensation on the surface of the ground was about 2-7 mm. January experienced the most dew condensation (7.2 mm). It was found that about 43 mm of dew condensation was generated over one year. To analyze the characteristics of evapotranspiration in the forest, the evapotranspiration on the surface was measured by the lysimeter method and the evapotranspiration on the upper part of the canopy was measured by the eddy covariance method. These results were compared and analyzed. Until mid-October, the evapotranspiration of the forest was active, and the amount of evapotranspiration on the top of the canopy was higher than the amount on the surface. Thereafter, the amount of evapotranspiration on the top of the canopy decreased due to the lowering of temperature and net-radiation. The amount of evapotranspiration on the surface and above the canopy showed the same tendency.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.5 s.118
• /
• pp.47-53
• /
• 2006

To meet the ever increasing quality demand of coated papers and duplex boards, the local gloss variation and print unevenness must be avoid. To do this, surface roughening phenomenon which affects local gloss and print unevenness was investigated. In this study, the effect of roughness and densification of sheet obtained at various calendering conditions on surface roughening was examined. To evaluate the calendering effect properly we introduced a new value of roughening index by moisture for evaluation of surface roughening. Caliper and roughness of sheet decreased with increasing of calendering temperature and pressure, and the remarkable reduction of those properties occurred at the temperature around Tg. Roughening index increased when the amount of water increased and calendaring temperature and pressure increased. And as the sheet became denser by calendering, the roughening index increased to some extent. But roughening index by moisture is the lowest for sheet precalendered at higher temperature condition. When the surface of calendered sheet is rougher, there is more roughening of surface. The severe condition of calendering made the roughening index by moisture small.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.4
• /
• pp.1-8
• /
• 2007

Japanese larch specimens with dimension of 2.5 (radial direction) ${\times}$ 2.5 (tangential direction) ${\times}$ 2.5 cm (longitudinal direction) were prepared to determine 3 different directional internal moisture movement coefficients and surface emission coefficients along the radial-, the tangential-, and the tangential-direction. 4 sides of each cubic specimen were wrapped with paraffin tape and rubber tape, leaving open the 2 opposite surfaces of interest, to provide one dimensional moisture movement during drying. The coefficients were determined at three different temperatures, 70, 50 and $30^{\circ}C$ and at two different relative humidities, 30 and 60%. Internal moisture movement coefficients inclusive of flow of free water and diffusion of bound water and water vapor were increased in the high temperature condition. The internal moisture movement coefficient in the longitudinal direction was about six times of those in transverse directions with radial value being 20% greater than the tangential. Surface emission coefficients were increased with temperature and decreased with surface moisture content. Using this results, moisture content (MC) profile and quantities of moisture evaporating in Japanese larch lumber could be predicted in dynamic drying situations.

• Journal of the Korea Institute of Building Construction
• /
• v.7 no.4
• /
• pp.125-132
• /
• 2007

The use of Self-Leveling material is increasing recently. This paper assesses the quality of surface layer of concrete floor when Self-Leveling material is defective. The paper shows how to predict the defect of SL material before construction begins. The relationship between the quality of surface layer of concrete floor and the defect of SL material was determined and the quality of surface layer of concrete floor was then estimated. The relations between the quality of surface layer and the defect of SL material were determine considering surface strength, moisture, and consistency of surface layer. Absorbing amount was used as the indicator of consistency and the absorbing amount of test material was measured. Then the relations between the test material and surface strength were determined. Generally concrete floor with greater consistency has greater surface strength, however in this study, we hound that high impact concrete floor could have lower surface strength as the consistency gets bigger. The relations between the level of defect occurred in SL material and the quality of surface layer were examined and we clarified that the surface layer with lower consistency gets higher possibility to occur exfoliation in early stage, one or two weeks after constructing SL material. When the consistency is sufficient, the occurring situation of defect depends upon the moisture of surface layer. Little amount of moisture gets higher possibility not to occur the defect. As the amount increases, fissure generates and early exfoliation may occur. In addition, the level of fissure is highly related with the surface strength.

• International Journal of Highway Engineering
• /
• v.20 no.1
• /
• pp.69-76
• /
• 2018

PURPOSES : This study determined the optimal usage rate of RAP (reclaimed asphalt pavement) using cold central-plant recycling (CCPR) on a road-surface layer. In addition, a mixture-aggregate gradation design and a curing method based on the proposed rate for the surface-layer mix design were proposed. METHODS : First, current research trends were investigated by analyzing the optimum moisture content, mix design, and quality standards for surface layers in Korea and abroad. To analyze the aggregate characteristics of the RAP, its aggregate-size characteristics were analyzed through the combustion asphalt content test and the aggregate sieve analysis test. Moreover, aggregate-segregation experiments were performed to examine the possibility of RAP aggregate segregation from field compaction and vehicle traffic. After confirming the RAP quality standards, coarse aggregate and fine aggregate, aggregate-gradation design and quality tests were conducted for mixtures with 40% and 50% RAP usage. The optimum moisture content of the surface-layer mixture containing RAP was tested, as was the evapotranspiration effect on the surface-layer mixture of the optimum moisture content. RESULTS : After analyzing the RAP recycled aggregate size and extraction aggregate size, 13-8mm aggregate was found to be mostly 8mm aggregate after combustion. After using surface-chipping and mixing methods to examine the possibility of RAP aggregate segregation, it was found that the mixing method contributed very little for 3.32%, and because the surface-chipping method applied compaction energy directly as the maximum assumption the separation ratio was 15.46%. However, the composite aggregate gradation did not change. Using a 40% RAP aggregate rate on the surface-layer mixture for cold central-plant recycling satisfied the Abroad quality standard. The optimum moisture content of the surface-layer mixture was found to be 7.9% using the modified Marshall compaction test. It was found that the mixture was over 90% cured after curing at $60^{\circ}C$ for two days. CONCLUSIONS : To use the cold central-plant recycling mixture on a road-surface layer, a mixture-aggregate gradation design was proposed as the RAP recycled aggregate size without considering aggregate segregation, and the RAP optimal usage rate was 40%. In addition, the modified Marshall compaction test was used to determine the optimum moisture content as a mix-design parameter, and the curing method was adapted using the method recommended by Asphalt Recycling & Reclaiming Association (ARRA).

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.1
• /
• pp.115-126
• /
• 2001

In this paper, through a series of comparative experiments, effects of two different cure processing methods, cocure and precure, on the mechanical properties of honeycomb core materials for aircraft applications are considered. Mass of moisture accumulated into the closed cells of the sandwich panel specimen from the measured mass of moisture diffused to the full saturation state into the elements(skin, adhesive layer, Nomex honeycomb), consisting the honeycomb sandwich specimen has been calculated. Water reservoir of 70$\^{C}$ was used to have specimens absorb moisture to see the influence of moisture absorbed into sandwich panel on its mechanical properties. For the repair condition holding for 2 hours at 177$\^{C}$(350℉) temperature, a pressure due to the vapor expansion in each cell of the sandwich panel, which may result in the local separation of the interface between laminated skin and the surface of the honeycomb, has been estimated by vapor pressure-temperature relation from the thermodynamic steam table and compared to the pressure from the ideal gas state equation. The bonding strengths of the laminated skins on the flat surface of the Nomex honeycomb have been compared by the flatwise tension test and climbing drum peel test performed at room temperature for dry, wet and wet-repair specimens, respectively.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.34 no.3
• /
• pp.29-36
• /
• 2018

In this study, the moisture contents of four Hanoks have been monitored and the results were analyzed. Murujeong and Ongojae were built by traditional construction method and material, and Jeeshinjae and Hwakyeongdang were built by modernized construction method and material. Hwakyeongdang was monitored about 2 years and 9 months and the other three Hanoks were monitored about 4 years and 2 months. The surface moisture contents were measured by the non-destructive electronic resistant type moisture content meter. The measured moisture contents were affected by the orientation to the sun, wood type, temperature and relative humidity. The columns on the northern side and lumber showed more moisture contents than those of the southern side and glue-laminated wood. The moisture contents and relative humidity showed proportional relationship. The moisture contents of all four monitored Hanoks existed proper range by and large.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.2
• /
• pp.59-63
• /
• 2008

The surface runoff is one of the important components for the surface water balance. However, most Land Surface Models(LSMs), coupled to climate models at a large scale for the prediction and prevention of disasters caused by climate changes, simplistically estimate surface runoff from the soil water budget. Ignoring the role of surface flow depth on the infiltration rate causes errors in both surface and subsurface flow calculations. Therefore, for the comprehensive terrestrial water and energy cycle predictions in LSMs, a conjunctive surface-subsurface flow model at a large scale is developed by coupling a 1-D diffusion wave model for surface flow with the 3-D Volume Averaged Soil-moisture Transport(VAST) model for subsurface flow. This paper describes the new conjunctive surface-subsurface flow formulation developed for improvement of the prediction of surface runoff and spatial distribution of soil water by topography, along with basic schemes related to the terrestrial hydrologic system in Common Land Model(CLM), one of the state-of-the-art LSMs.