• Journal of the Korean institute of surface engineering
• /
• v.48 no.1
• /
• pp.1-6
• /
• 2015

Amino-carboxyl acid as a complexing agent in acid copper sulfate solution was utilized to improve the adhesion of immersion copper layer for steel wire. According to the tape test results, regardless of alloy composition of the wire, the adhesion of immersion copper layer was improved with the addition of amino-carboxyl acid. The incorporation of H and Fe in the plating layer was analyzed by TOF-SIMS. The H and Fe were detected at the entire coating layer without any addition of amino-carboxyl acid. However, with addition of amino-carboxyl acid, the H and Fe were scarcely detected at the coating layer.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.1-11
• /
• 2021

Performance of a NACA 63₄-021 hydrofoil in motion under and in close proximity of a free surface for a large range of angles of attack is studied. Lift and drag coefficients of the hydrofoil at different submergence depths are investigated both numerically and experimentally, for 0° ≤ AoA ≤ 30° at a Reynolds number of 10⁵. The results of the numerical study are in good agreement with the experimental results. The agreement confirms the new finding that for a submerged hydrofoil operating at high angles of attack close to a free surface, the interaction between the hydrofoil-motion induced waves on the free surface and the hydrofoil results in mitigation of the flow separation characteristics on the suction side of the foil and delay in stall, and improvement in hydrofoil performance. In comparing with a baseline case, results suggest a 55% increase in maximum lift coefficient and 90% average improvement in performance for, based on the lift-to-drag ratio, but it is also observed significant decrease of lift-to-drag ratio at lower angles of attack. Flow details obtained from combined finite volume and volume of fluid numerical methods provide insight into the underlying enhancement mechanism, involving interaction between the hydrofoil and the free surface.

• Journal of the Korean institute of surface engineering
• /
• v.26 no.3
• /
• pp.115-120
• /
• 1993

Aluminum thin films were deposited on the silicon substrate by the pyrolysis of TrilsoButylAluminum (TIBA) in a cold wall LPCVD reactor. The effect of substrate on the surface topograply and the decomposition reaction was investigated. The activation energy for the decomposition of TIBA was turned out to be 1 eV from the Arrhenious plot. The surface topography of the CVD aluminum could be improved by the application of thin metal film, which was in-situ deposited on the silicon prior to CVD process.

• The Journal of Korean Physical Therapy
• /
• v.34 no.4
• /
• pp.161-167
• /
• 2022

Purpose: The purpose of this study was to investigate the effects of regular training on the uneven surface that stroke patients encounter in their daily life on their ankle joint muscle activity and balance ability. They were divided into two groups: the gait training group on uneven surfaces and the gait training group on normal surfaces. Methods: In this study, 30 patients diagnosed with stroke and undergoing rehabilitation were selected. 15 people in the uneven surface gait training group and 15 people in the flat gait training group were selected. The muscle activation of the ankle muscles was measured when walking again on a even surface after walking on an uneven surface and on a flat ground. After each gait training, the limit of stability and Romberg test were performed to evaluate the balance ability. Results: As a result of the experimental results before and after walking by group, the tibialis anterior muscle activity of the paralyzed side was significantly decreased in the uneven surface walking group. As a result of measuring balance ability after training, the limit of stability in all directions was significantly increased in the uneven surface gait training group, and the area and length moved significantly decreased in the uneven surface gait training group in the Romberg test as well (p<0.05). Conclusion: After walking on uneven surface, it was confirmed that the muscle activity of the ankle joint decreased in normal flat walking, and thus the efficiency of muscle activity was increased. In addition, it was possible to confirm the improvement of the balance ability of the gait training on the uneven surface, and in conclusion, it could be confirmed that it had an effect on the improvement of the walking ability.

• Composites Research
• /
• v.30 no.6
• /
• pp.416-421
• /
• 2017

The structural adhesive have been manufactured for improvement of bonding process between CFRP and metal. The optimal condition for bonding process were investigated by evaluating the lap shear strength with amount of adhesive and curing time and the surface treatment of the CFRP. To confirm proper adhesion conditions, the fracture sections between CFRP and metal was observed using reflection microscope. Not only the improvement of the adhesion condition was important, but surface treatment on CFRP was also important. The optimal curing temperature was at $180^{\circ}C$ for 20 minutes. The improvement for adhesive property was confirmed After surface treatment on CFRP. The optimal amount of structural adhesive for bonding between CFRP and metal was $1.5{\times}10^{-3}g/mm^2$. Through the optimization of bonding process, the improvement of mechanical property over 10% is confirmed in comparison with existing adhesive.

• Archives of Plastic Surgery
• /
• v.42 no.3
• /
• pp.282-287
• /
• 2015

Background Morphological changes that accompany aging, such as wrinkles and skin laxity, are particularly prominent on facial skin. Recently, facial rejuvenation using the hydrofilling effect of hyaluronic acid (HA) filler has been employed for improvement of skin texture. In this study, we studied rejuvenating effects of stabilized HA (Restylane Vital) through direct intradermal injections. Methods A total of 30 female patients underwent a series of procedures on face, including three sessions at intervals of four weeks. A total of 2 mL of Restylane Vital was injected along the whole face using an automatic injector. Improvement of skin surface roughness, elasticity, brightness, moisture, and fine wrinkles was evaluated. Patient satisfaction was evaluated, and pictures of patients were taken at each visit and 6 months after last treatment session. Scoring for each patient was performed by three doctors according in five subjects. Moisture, oil and elasticity were measured before the procedure and before the last treatment in 10 patients. Results The majority of patients (77%) were satisfied with the therapeutic outcomes. Approximately 66% of patients responded that the effects of this procedure persisted for longer than four months, and the majority of patients (77%) wanted to undergo this procedure again and would recommend this procedure to acquaintances. Regarding doctors' evaluation, scores for improvement of skin surface roughness, elasticity, and brightness were significantly higher than those for improvement of moisture and fine wrinkle. Conclusions Intradermal injection of HA can have a rejuvenating effect on dry and tired facial skin, especially in improvement of skin surface roughness.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.53 no.1
• /
• pp.55-64
• /
• 2004

Conventional bipolar surface electromyography(EMG) technique detects only the superimposed electromyographic activity of a large number of motor units due to its low spatial resolution. For the diagnosis of neuromuscular disorder, the information of single MU is required. In this paper, 9 channel array surface electrode system was as designed and MLoG filter was proposed. Also the MCPT(modified convolution processing technique)method was proposed for the improvement of MUAP resolution. For performance evaluation, power spectrum analysis of random data and raw EMG signal comparison of MUAP shape and quantitative estimation of SNR were executed. As a result, the MUAP resolution improvement of 32％ was obtained from the standpoint of the signal-to-noise ratio(SNR).

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.777-778
• /
• 2006

This paper deals with the optimum rotor design approach about the multi-layer design of the buried magnets in an Interior Permanent Magnet Synchronous Motor (IPMSM), on the efficiency improvement by using Response Surface Methodology (RSM). In the multi-layer design of the prototype 15kw IPMSM, the constant amount of buried PM is split from the single-layer into double-layer design for improving the efficiency characteristics. The optimum double-layer rotor structure is built with the help of RSM analysis. The improvement of IPMSM efficiency is verified by the Finite Element Method (FEM) results comparison with the prototype single-layer IPMSM.

• Journal of the Korean institute of surface engineering
• /
• v.16 no.3
• /
• pp.98-107
• /
• 1983

A study on the improvement of wear resistance of brasses by electroplating and diffusion treatment of tin was carried out. The optimum condition of the treatment obtained was as follows. Plating thickness of tin : 5 - 9 $\mu\textrm{m}$ Condition of diffusion treatment : atmosphere ; fused nitrate bath (KNO3 + NaNO3) temperature and time ; 1st step 320$^{\circ}C$, 60min. and 450$^{\circ}C$, 30min. During the diffusion treatment, internetallic compounds of Cu-Sn were formed and these compounds were identified as η, $\varepsilon$ and $\delta$ phase from the outer tin layer. It was considered that the improvement of wear resistance of brasses by the treatment is because of the formation of intemetallic compounds particalarly $\varepsilon$phase which is very hard, between soft tin layer brass.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.2
• /
• pp.51-56
• /
• 2022

Recently, the demand for semiconductors is expanded to various industries, and the use of high-quality and high-performance chips is increasing. With the trend, the diameter magnification and high integration of the semiconductor wafers are mandatory. As a result, there is a growing demand for the productivity improvement and the surface precision. There have been many studies on the stabilization of the wafer manufacturing processes in order to satisfy those specifications. Many complaints have been appealed by the wafer buyers that there are many unacceptable wafers with surface defects and foreign material adhesion which are caused by the vibrations during transportation. This study intends to derive the material improvement of the packing box of the wafers to suppress the vibrations of the box, and eventually to reduce the surface defects and the foreign material adhesion. The result shows that optimal material can substantially decrease the vibration of the packing box.