• Korean Journal of Materials Research
• /
• v.3 no.3
• /
• pp.292-299
• /
• 1993

In this paper the effects of the length of carbon fiber on the wear properties of carboni carbon composites were investigated. Carbon/carbon composites were fabricated by the liquid impregnation method using the resol-type phenolic resin as a matrix precursor and PAN-based, non-surface treated carbon fiber as a reinforcement. The measured values of the friction coefficient of carbon/carbon composites against AlSl 304 stainless steel ranged from 0.2 to 0.3 under the operating condition used in this study. The effect of the length of carbon fiber on the friction coefficient of carbon/carbon composites were not found. But, it was realized that the wear rate of carbon/carbon composites tends to increase, as the length of carbon fiber increases.

• Applied Chemistry for Engineering
• /
• v.23 no.6
• /
• pp.604-607
• /
• 2012

Solid base catalysts for biodiesel production were synthesized by impregnating basic metal species on two support materials with large specific surface area : zeolite and pyrolysis char. KL zeolite and Undaria pinnatifida char were impregnated with KOH aqueous solution and calcium nitrate solution, respectively, to enhance the basic strength. The catalysts synthesized were characterized using Hammett indicators and $CO_2$-TPD analysis. Biodiesel was produced using soybean oil and methanol over the catalysts synthesized. The content of fatty acid methyl esters was measured to evaluate the catalytic activity. Generally, the catalytic activity increased with increasing quantity of basic metal impregnated but impregnation of excessive amount of metal could cause reduction in the activity.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.3
• /
• pp.344-359
• /
• 2019

Effects of various types of zeolite on the catalytic performance of hydrodeoxygenation (HDO) of bio-oil obtained from waste larch wood pyrolysis were investigated herein. Bifunctional catalysts were prepared via wet impregnation. The catalysts were characterized through XRD, BET, and SEM. Experimental results demonstrated that HDO enhanced the fuel properties of waste wood bio-oil, such as higher heating values (HHV) (20.4-28.3 MJ/kg) than bio-oil (13.7 MJ/kg). Water content (from 19.3 in bio-oil to 3.1-16.6 wt% in heavy oils), the total acid number (from 150 in bio-oil to 28-77 mg KOH/g oil in heavy oils), and viscosity (from 103 in bio-oil to $40-69mm^2/s$ in heavy oils) also improved post HDO. In our experiments, depending on the zeolite support, NiFe/HBeta exhibited a high Si/Al ratio of 38 with a high specific surface area ($545.1m^2/g$), and, based on the yield of heavy oil (18.3-18.9 wt%) and HHV (22.4-25.2 MJ/kg), its performance was not significantly affected by temperature and solvent concentration variations. In contrast, NiFe/zeolite Y, which had a low Si/Al ratio of 5.2, exhibited the highest improved quality for heavy oil at high temperature, with an HHV of 28.3 MJ/kg at $350^{\circ}C$ with 25 wt% of solvent.

• Korean Chemical Engineering Research
• /
• v.59 no.2
• /
• pp.269-275
• /
• 2021

In this study, ordered mesoporous silica-supported Ni catalysts were prepared for catalytic partial oxidation of methane (CPOM) by using electroless nickel plating method. Unlike conventionally impregnated catalysts, the electrolessly-plated nickel catalyst showed that nickel was highly dispersed and formed stably on silica-supported surface. It was verified by TEM-EDS analysis. During the activity tests, the electrolessly-plated nickel was barely sintered and the amount of carbon deposition was very small. Consequently, the catalyst was far less deactivated, while the sintering was significantly observed in the cases of the catalysts prepared by the conventional impregnation method. Regarding the palladium-promoted catalysts, the reducibility of nickel was increased, and the reaction performances were enhanced in terms of CH4 conversion and H2/CO ratio of produced syngas.

• Animal Systematics, Evolution and Diversity
• /
• v.38 no.4
• /
• pp.226-237
• /
• 2022

Arcuospathidium is a haptorian ciliate genus composed of 18 species, and only one species has been reported in Korea. Here, we identify two unrecorded Arcuospathidium subspecies by morphological observation of both living and protargol-impregnated specimens with the small subunit ribosomal RNA (18S rRNA) gene sequence. These subspecies, Arcuospathidium cultriforme cultriforme (Penard, 1922) Foissner, 1984 and A. cultriforme scalpriforme (Kahl, 1930) Foissner, 2003, were isolated from various terrestrial habitats in July and August 2013, respectivley. Arcuospathidium cultriforme cultriforme is similar to A. cultriforme scalpriforme by a knife-shaped body, a twisted-shaped macronucleus, number of dorsal brushes, position of dorsal brushes, and shape of macronucleus but former mainly differs from the body length to oral bulge length ratio (27-38% vs. 41-53%), extrusome (one types vs. three types), cyst shape (roughly faceted wall vs. smooth surface and thin wall) and number of somatic kinety rows(18-30 vs. 30-44). Additionally, we analyzed the 18S rRNA gene sequences of two A. cultriforme subspecies and compared them with the sequences from GenBank to confirm their identification at the molecular level. As the results of genetic analysis, the 18S rRNA gene sequence of the Korean A. cultriforme cultriforme population is most similar to that of Austrian population. Also, the sequence of the Korean A. cultriforme scalpriforme population is most similar to that of another population with some nucleotide differences.

• Korean Journal of Materials Research
• /
• v.32 no.3
• /
• pp.125-131
• /
• 2022

Effect of sulfation processes on the physicochemical properties of ZrO₂ and TiO₂ nanoparticles were thoroughly investigated. SO₄/ZrO₂ and SO₄/TiO₂ catalysts were synthesized to identify the acidity character of each. The wet impregnation method of ZrO₂ and TiO₂ nanoparticles was employed using H2SO₄ with various concentrations of 0.5, 0.75, and 1 M, followed by calcination at 400, 500, and 600 ℃ to obtain optimum conditions of the catalyst synthesis process. The highest total acidity was found when using 1 M SO₄/ZrO₂-500 and 1 M SO₄/TiO₂-500 catalysts, with total acidity values of 2.642 and 6.920 mmol/g, respectively. Sulfation increases titania particles via agglomeration. In contrast, sulfation did not practically change the size of zirconia particles. The sulfation process causes color of both catalyst particles to brighten due to the presence of sulfate. There was a decrease in surface area and pore volume of catalysts after sulfation; the materials' mesoporous structural properties were confirmed. The 1 M SO₄/ZrO₂ and 1 M SO₄/TiO₂ catalysts calcined at 500 ℃ are the best candidate heterogeneous acid catalysts synthesized in thus work.

• Clean Technology
• /
• v.30 no.1
• /
• pp.62-67
• /
• 2024

In this study, an alkali metal Na was introduced into iron-based catalysts used in the carbon dioxide-based Fischer-Tropsch process by wet impregnation and physical mixing methods to compare their performance. The as-prepared catalysts were evaluated for reactivity at 3.5 MPa, 330 ℃, feed ratio of H₂/CO₂ = 3 with a space velocity of 4,000 mL h^-1 g_cat^-1. Comparing the two catalysts, it was found that Na was uniformly distributed throughout the catalyst when wet-impregnated, but Na for physically mixed catalyst was relatively located on the surface of the catalyst. In addition, the wet-impregnated catalyst showed higher liquid hydrocarbon (C₅₊) yield and lower CO selectivity. In conclusion, the effect of Na distribution in the catalyst on the reaction was identified and can be controlled by the introduction method.

• Applied Chemistry for Engineering
• /
• v.3 no.1
• /
• pp.53-63
• /
• 1992

M/BM -series catalysts, $MoO_3$ supported on ${\alpha}-Bi_2Mo_3O_{12}$ were also prepared by impregnation method. BM/M-series catalysts, ${\alpha}-Bi_2Mo_3O_{12}$ supported on $MoO_3$ were also prepared by coprecipitation. Structure and catalytic properties of the two phase catalysts were studied by means of using nitrogen adsorption, X-ray diffraction, and scanning electron microscopy. The reaction test for the selective oxidation of propylene to acrolein over Bi-molybdate catalysts was studied using a fixed-bed reactor system. In M/BM-series catalysts, $MoO_3$ was dispersed on ${\alpha}-Bi_2Mo_3O_{12}$, and the crystal structure of ${\alpha}-Bi_2Mo_3O_{12}$ remains unchanged by the presence of excess $MoO_3$. However the surface morphology and bulk structure of BM/M-series catalysts were altered probably because the precipitated $Bi(OH)_3$ reacted with $MoO_3$ during the calcination to form ${\alpha}-Bi_2Mo_3O_{12}$ phase. The results of propylene oxidation on both series catalysts showed that the reaction took place over the surface of ${\alpha}-Bi_2Mo_3O_{12}$ particle and the role of excess $MoO_3$ was to supply oxygen to ${\alpha}-Bi_2Mo_3O_{12}$. These increasing effects on activity were also observed in the mechanical mixtures of ${\alpha}-Bi_2Mo_3O_{12}$ and $MoO_3$.

• Polymer(Korea)
• /
• v.24 no.5
• /
• pp.701-712
• /
• 2000

The continuous fiber reinforced composites of GF/PA were fabricated using a pultrusion resin impregnation apparatus and cut into pellets of 6 mm length. GF/PA pellets were then melt-mixed with PP resin to prepare new types of ternary composites, GF/PA/PP. Mechanical and rheological properties of such composites revealed to be better than conventional ternary composites due to the longer average glass fibers. Measurements also showed that the mechanical properties of the composites prepared by direct injection molding were higher than those of the composites prepared by injection molding followed by extrusion. To improve adhesions of fiber surfaces and polymer matrix, PP-MAH (maleic anhydride) has been introduced in the GF/PA/PP composites as a compatibilizer. It was found that PP-MAH did indeed improve surface adhesion between fibers and polymer matrix and that, as a result, various mechanical properties were markedly enhanced. Visualization of the phase structure in the samples was done by means of SEM. The surfaces of glass fibers in GF/PA/PP composites revealed that the fibers remained to be encapsulated by PA resin. However, pre-encapsulation did not persist in GF/PA/PP/PP-MAH composites due to the improvement of surface adhesion between fibers and polymer matrix, although resin sticking to the fiber was observed.

• Journal of Adhesion and Interface
• /
• v.14 no.3
• /
• pp.117-120
• /
• 2013

The prepreg material is a sheet of the reinforcement pre-impregnated with a resin. In this study, two types of prepreg were prepared with a general phenolic resin and the polyvinyl butyral (PVB) modified phenolic resin, respectively, with resin content of 40 wt%. After resin impregnation, the prepregs were heat treated in an oven to make them the B-stage. Surface morphology of the prepreg was observed by using a scanning electron microscope (SEM). Tack property of the prepreg is one of the major properties that govern the ability of prepreg to be laid up. In this study, the tack of prepreg was measured under various test parameters by a probe tact test. Test parameters were contact time, contact force and debonding rate. Most of the tack properties of the prepreg increased with the test parameters. Then tack properties exhibited a linear behavior with test parameters before a saturation point. Also, the tack of prepreg was investigated in relation with the fibrillation phenomena involved in the prepreg surface with the debonding rate.