• Applied Chemistry for Engineering
• /
• v.18 no.5
• /
• pp.467-474
• /
• 2007

The palladium and gold nanoparticles containing PAN-based active carbon fiber (ACF) with a high specific surface area were prepared. Using the BET, TEM, FE-SEM, and XPS, their specific surface area and pore volume, pore structure, and the change in surface oxygen groups with time were analyzed and $SO_2$ adsorption performances were investigated. Because of the impregnating process, the micropore volume was mostly decreased from 95.5% to 30.5~43.7% compared with the total pore volume. And the change in surface oxygen groups with time was higher for the metal salt than the nanoparticles. Also, $SO_2$ breakthrough time of PAN-ACFs impregnated with Au nanoparticles and metal salts did not change compared with that of the non-impregnated PAN-ACF. But the PAN-ACF impregnated with Pd nanoparticles (100 ppm) showed good $SO_2$ adsorption performance as the breakthrough time of 880 sec. These results indicated that the $SO_2$ adsorption performance depended on the change in surface oxygen groups with time and the moderate impregnation of Pd nanoparticles on the PAN-ACF caused the increase in the $SO_2$ adsorption performance by a catalytic action.

• Science of Emotion and Sensibility
• /
• v.26 no.1
• /
• pp.79-86
• /
• 2023

This study aims to create a highly conductive E-textile made by recycling PET with a Dip-coating process. PET fiber with hydrophobic properties is characterized by the difficulty in imparting great conductivity when both Virgin and Recycled are made of electronic fibers through a Dip-coating process. To advance the effectiveness of the Dip-coating process, a sample made of recycled PET was surface modified for 50 w 5 minutes and 10 minutes employing a Covance-2mprfq model from FEMTO SCIENCE. After that, the sample was immersed in an SWCNT dispersion (.1 wt%, Carbon Co., Ltd.) for 5 minutes, and then dip coating was conducted to allow the solution to permeate well into the sample through a padder (DAELIM lab). After the procedure was completed, the resistance measurement was measured with a multimeter at both ends and then accurately remeasured with a wider electrode. As a result of this contemplation, it was affirmed that great conductivity might be given through an impregnation process through the plasma surface modification. When the surface modification was performed for 10 minutes, the resistance was reduced by up to 2.880 times. Dependent on the results of this research, E-fibers employed in the smart wearable sector can also be made of recycled materials, improving smart wearable products that can save oil resources and reduce carbon emissions.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.2
• /
• pp.203-210
• /
• 2000

The preparative methods of a chitosan-deposited activated carbon and its characteristics were studied by using three kinds of chitosan with different degree of deacetylation and average molecular weight. The procedure was consisted of the dissolution of chitosan into acid solution, impregnation of activated carbon, agitation, evaporation, and drying. When the chitosan-dissolved acid and its concentration, amounts of chitosan deposited, and agitation conditions were changed, the specific surface area, deposition state on surface, and stability were investigated, and amounts of Cr(VI) adsorbed was measured. In the preparation process, it was proper to agitate the chitosan-dissolved acetic acid solution at room temperature for 1hr. In the deposition of chitosan with low molecular weight, the specific surface area of activated carbon was greatly decreased even at low chitosan loading, but in the case of high molecular weight it was not nearly changed to 10wt% loading. It was known that chitosan was uniformly and physically deposited on activated carbon. The chitosan-deposited activated carbon was stable into the solution over about pH 6. The removal of Cr(VI) was remarkably enhanced by adding the adsorption function of chitosan to the surface of activated carbon with about 5wt% chitosan. It may be therefore used as an adsorbent for removing the pollutants in air and wastewater.

• Clean Technology
• /
• v.21 no.1
• /
• pp.68-75
• /
• 2015

In this study, we investigated the structure and properties of a highly heat conductive metal-ceramic core-shell CoAl₂O₄@Al micro-composite for heterogeneous catalysts support. The CoAl₂O₄@Al was prepared by hydrothermal surface oxidation of Al metal powder, which resulted in the structure with a high heat conductive Al metal core encapsulated by a high surface area CoAl₂O₄ shell. For comparison, CoAl₂O₄ was also prepared by co-precipitation method and also utilized for a catalyst support. Rh catalysts supported on CoAl₂O₄@Al and CoAl₂O₄ were prepared by incipient wetness impregnation and characterized by N₂ adsorption, X-ray diffraction (XRD), scanning electron microscopy (SEM), CO chemisorption, and temperature-programmed reduction (TPR). The properties of catalysts were investigated for glycerol steam reforming reaction for hydrogen production at 550 ℃. Rh/CoAl₂O₄@Al exhibited about 2.8 times higher glycerol conversion turnover frequency (TOF) than Rh/CoAl₂O₄ due to facilitated heat transport through the core-shell structure. The CoAl₂O₄@Al and CoAl₂O₄ also showed some catalytic activities due to a partial reduction of Co on the support, and a higher catalytic activity was also found on the CoAl₂O₄@Al core-shell than CoAl₂O₄. These catalysts, however, displayed deactivation on the reaction stream due to carbon deposition on the catalysts surface.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.9
• /
• pp.900-906
• /
• 2008

It was studied to utilize wasted food as a starting material to produce for activated carbon. The wasted food was chemically activated with zinc chloride. Experiments were carried out at different chemical ratios(activating agent/wasted foods), activation temperatures, and activation time. The activated products were characterized by measuring the iodine and methylene blue number, the BET surface area, the pore volume, the micropore ratio, the pore diameter, the yields and the scanning electron microscope(SEM). For the products activated by impregnation ratio of 1.0 of ZnCl$_2$ at 500$^{\circ}C$ for 60 min in a rotary kiln reactor had iodine number of 480 mg/g, methylene blue number of 95 mL/g, BET surface area of 410 m$^2$/g, pore volume of 0.248 cm$^3$/g, and average pore diameter of 2.43 nm, respectively. The activated carbon obtained had the contribution of micropore area of 70.7% to the total pore area and micropore volume of 53.2% to the total pore volume.

• Journal of Environmental Impact Assessment
• /
• v.29 no.3
• /
• pp.198-209
• /
• 2020

In this study, electrospun nanofibers made of PAN (polyacrylonitrile) were activated through a physical method to obtain an optimized pore structure. In particular, to enhance the surface alkalinity, the activated carbon fibers (ANFs) were impregnated with tetraethylenepentamine (TEPA) with the aid of HNO₃. Then, the low level (3,000 ppm) CO₂ adsorption capacity for each ANF sample was evaluated. The specific surface area of ANFs increased from 308.4 ㎡/g to 839.4 ㎡/g and the total pore volume increased from 7.882 ㎤/g to 27.50 ㎤/g. Although the TEPA impregnation reduced the specific surface area and pore volume of the ANFs due to blocking of micropores, the HNO₃ pre-oxidation enhanced the amino groups tethered, increasing the amine content from 6.42% to 17.19%, and finally, increased the adsorption capacity of CO₂. This study showed that the sample 60-ANF-HNO₃-TEPA, which was activated for 60 minutes and was impregnated with HNO₃ and TEPA, had the best adsorption capacity for low level (0.3%) CO₂ (in a binary mixture with N₂).

• Korean Chemical Engineering Research
• /
• v.55 no.2
• /
• pp.156-162
• /
• 2017

CuO(x)/0.3Al-0.7Ce catalysts with different CuO loadings (x = 2~20 wt%) were prepared by impregnation method and investigated the effects of CuO loadings on the low temperature CO oxidation. Of the used catalysts, the CuO(10)/0.3Al-0.7Ce catalyst showed the highest catalytic performance in the absence or presence of water vapor. In the presence of water vapor, the catalytic performance was drastically decreased, with a temperature of 50% CO conversion ($T_{50%}$) shifted to higher temperature by $50^{\circ}C$ compared to the those in dry conditions because of the competitive adsorption of water vapor on the active sites. The copper metal surface area calculated from $N_2O$-titration analysis and the oxygen capacity from CO-pulse experiments were increased with the CuO loadings and showed a maximum at 10 wt%CuO/0.3Al-0.7Ce catalyst. These trends are in good agreement with the tendency of $T_{50%}$ of the catalysts. From these characteristic aspects, it could be deduced that the catalytic performance was closely related to the oxygen capacity and the copper metallic surface area.

• Journal of Conservation Science
• /
• v.37 no.5
• /
• pp.536-544
• /
• 2021

In the present study, safe management and value improvement of bamboo sunblind, which is an item of cultural heritage, were performed by adopting stable conservation treatment methods. The bamboo sunblind used in the present study was excavated from No. 1 catchment site in Baesanseongji, Busan. It was determined that the main material used to make the sunblind was bamboo, and herbal plants were used to weave the bamboo using lacquer as an adhesive agent. All contaminants and soil adhered to the sunblind was removed. Thereafter, the sunblind, which was recovered in the form of blocks, was washed separately after fixing it to a temporary plaster frame and to avoid the blocks from breaking during washing. Then, polyethylene glycol (PEG) impregnation was utilized for the reinforcement treatment. Based on the preliminary test results, the shape of the sunblind was fixed using a stainless-steel frame to prevent physical damage that may occur during the drying process. Thereafter, the bamboo sunblind was vacuum freeze-dried. PEG 20% (in ethyl alcohol) was applied as a surface treatment agent for stabilization the sunblind. After the surface treatment, the bamboo sunblind were joined together to fit the maximum width, and the rectangular shape of the sunblind was restored-as best as possible-while filling in the missing parts by maximizing the use of unknown members such as in the disturbed layers below bamboo sunblind surface. The conservation treatment was completed by fixing the bamboo sunblind into the fabricated frame.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.32 no.3
• /
• pp.89-95
• /
• 2022

In this study, glassy carbon coating was performed on the graphite using a phenolic resin and a curing agent was mixed with ethylene glycol as an additive to form the uniform surface. The phenolic resin was dried and cured under the environments of hot air, then converted into a glassy carbon layer by pyrolysis at 500~1,500℃. FTIR, XRD, SEM analysis, and density/porosity/contact angle measurement were performed for characterization of glassy carbon. The pyrolysis temperature for high-quality glassy carbon was optimized to be about 1,000℃. As the content of the additive increased, the effect of reducing surface defects on the coated surface, reduction of porosity, increase of contact angle, and increase of density were investigated in this study. The method of forming a glassy carbon coating layer through an additive is expected to be applicable to graphite coating and other fields.

• Clean Technology
• /
• v.15 no.1
• /
• pp.47-53
• /
• 2009

Mesoporous aluminas (A-C, A-A, and A-N) were prepared by a templating method using cationic(C), anionic(A), and non-ionic(N) surfactant as a structure-directing agent, respectively. Nickel catalysts supported on mesoporous alumina (Ni/A-C, Ni/A-A, and Ni/A-N) were then prepared by an impregnation method, and were applied to hydrogen production by steam reforming of liquefied natural gas (LNG). Regardless of surfactant type, nickel species were finely dispersed on the surface of mesoporous alumina in the calcined catalysts. It was revealed that interaction between nickel species and support in the reduced catalysts was strongly dependent on the identity of surfactant. LNG conversion and $H_2$ composition in dry gas increased in the order of Ni/A-C < Ni/A-A < Ni/A-N. It was found that catalytic performance increased with increasing nickel surface area in the reduced catalyst. Among the catalyst tested, Ni/A-N catalyst with the highest nickel surface area showed the best catalytic performance.