• Elastomers and Composites
• /
• v.50 no.2
• /
• pp.119-125
• /
• 2015

Because of their low surface free energy and absence of polar groups at the surface, polyolefins are substrates whose wetting and adhesion are very difficult. Free radical grafting of monomers to backbone polymer is one of the most attractive ways for the chemical modification of polymers. Synthesis of graft copolymer through graft polymerizations of PE and/or PP with phthalic anhydride (PhAn) was made and FTIR spectra of the graft polymer were the examined. And also the effects of phthalic anhydride content on the grafting ratio, thermal properties and contact angle of the graft polymer were examined.

• Polymer(Korea)
• /
• v.26 no.2
• /
• pp.279-286
• /
• 2002

For surface modification of polymers with hydrophilic functional groups, acrylic acid was grafted and immobilized on the surface of polyethylene(PE) by cold-plasma treatment using Ar gas. The modifications were identified by analysis of ATR-IR spectrum and by the measurement of contact angles. Compared to virgin PE significant decreases in contact angle were observed for both the grafted PE and the immobilized PE. The decreases of contact angle were in the range of 47~$53^{\circ}$ for grafted PE and 23~$26^{\circ}$ for immobilized PE. The degree of hydrophilicity depended strongly on the plasma-treating time and discharge power. For the case of grafting it has show that the longer plasma-treating time, the higher hydrophilic character. For the case of immobilization, whereas, higher discharge power and longer exposure to plasma have shown the detrimental effect for the preparation of hydrophilic PE surface due to the decrease of carboxyl group by ablation effect. The decrease in adhesion strength of immobilized PE. compared to grafted PE, was also attributed to the ablation of carboxyl group.

• Proceedings of the Korean Fiber Society Conference
• /
• 1994.04a
• /
• pp.107-107
• /
• 1994

• Journal of Radiation Industry
• /
• v.6 no.4
• /
• pp.317-322
• /
• 2012

In this study, the preparation of a temperature-responsive poly(N-isopropylacrylamide) (PNIPAAm)-grafted surface was performed using an eco-friendly and biocompatible ion beam-induced surface graft polymerization. The surface of a perfluoroalkoxy (PFA) film was activated by ion implantation and N-isopropylacrylamide (NIPAAm) was then graft polymerized selectively onto the activated regions of the PFA surfaces. Based on the results of the peroxide concentration and grafting degree measurements, the amount of the peroxide groups formed on the implanted surface was dependant on the fluence, which affected the grafting degree. The results of the FT-IR-ATR, XPS, and SEM confirmed that the NIPAAm was successfully grafted onto the implanted PFA. Moreover, the contact angle measurement at different temperatures revealed that the surface of the PNIPAAm-grafted PFA film was temperature-responsive.

• Polymer(Korea)
• /
• v.32 no.5
• /
• pp.497-500
• /
• 2008

Polystyrene foam (styrofoam) was treated with low-temperature oxygen plasma by means of immobilization and grafting techniques in order to modify its hydrophobic surface property to hydrophilic one using hydrophilic monomers of acrylic acid and acrylamide, and its surface chemical structure, morphology, and hydrophilicity were examined by ESCA, field emission scanning electron microscope (FESEM), and contactangle meter. The experimental evidences, such as the increases of O/C and N/C ratios in ESCA spectrum, thin film deposition, decrease in contact-angle, strongly suggested that the plasma treatments were useful methods for the preparation of hydrophilic surface. Contact angle diminished drastically from $84^{\circ}$ to $18{\sim}19^{\circ}$. Acrylamide, compared to acrylic acid, appeared to play a decisive role, and to be more powerful agent for improving its surface hydrophilicity.

• Journal of the Korean Chemical Society
• /
• v.6 no.1
• /
• pp.64-68
• /
• 1962

The graft polymerization of styrene to polyvinyl alcohol using a photosensitizer(benzophenone) and ultraviolet light was studied. Styrene was grafted onto polyvinyl alcohol up to when polyvinyl alcohol was pre-immersed in water and irradiated by ultraviolet light for 24 hours styrene solution of benzophenone(0.01 molarity). The highest percentage of graft obtained in the grafting which was proceeded in the presence of water added immediately before irradiation was 29%. The grafting was proportional to irradiation time within a certain limit of time, i.e., 24 hours, and presumably was initiated at the surface. After a certain degree of grafting a definite maximum was reached. Graft polymer prepared in this experiment showed high resistance to various solvents.

• Macromolecular Research
• /
• v.11 no.5
• /
• pp.347-351
• /
• 2003

The hydrophobic ligand-containing hollow polypropylene (PP) membranes were synthesized by the mutual radiation induced graft copolymerization with glycidylmethacrylate (GMA) onto hollow PP membrane followed by the subsequent functionalization with L-phenylalanine. FT-IR, elemental analysis and UV spectroscopy were utilized to characterize copolymer composition, and degree of grafting, functionalization conversion and ${\gamma}$-globulins adsorption. The degree of grafting on the PP surface increased with the reaction time and total dose of E-beam. In the subsquent functionalization, the amount of L-phenylalanine increased with the increase in the degree of grafting and the degree of conversion was about 30%. The ${\gamma}$-globulins adsorption experiments showed that adsorption capacity had a maximum value at pH 8. The ${\gamma}$-globulins adsorption capacity in the basic pH region was higher than in the acidic pH region.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2004.05a
• /
• pp.110-112
• /
• 2004

Poyethylene films can be modified by radiation grafting of N-vinyl pyrollidone using y-radiation. FTIR spectra were used to confirm the modification of PE films. The modified films were activated by two-step and one step methods for electroless Cu plating. Morphology of metallized films has been investigated. Electroless Cu plating onto the modified films depends mainly on the grafting degree and activation type. The conductivity of the metallized films has been investigated.

• Polymer(Korea)
• /
• v.38 no.3
• /
• pp.293-298
• /
• 2014

We prepared hydrophilic porous supporters for the reinforced composite fuel cell membrane by radiation grafting of acrylonitrile (AN) and hydrophilic sodium allylsulfonate (SAS) into a porous polytetrafluoroethylene (PTFE) supporter. The physicochemical properties of the supporters prepared under various reaction conditions such as molar ratio of SAS/AN, monomer concentration, and irradiation dose were evaluated. FTIR was utilized to confirm the successful introduction of SAS/AN copolymer chains into the porous PTFE. The pores of the porous PTFE film were found to be decreased with an increase in the degree of grafting by using FE-SEM and gurley number. Furthermore, by analyzing the degree of grafting, contact angle, and TBO (toluidine blue O) uptake, the hydrophilicity of the prepared supporters was found to increase with an increase in the degree of grafting.

• Polymer(Korea)
• /
• v.36 no.3
• /
• pp.302-308
• /
• 2012

The objective of this study is to investigate optimum reaction conditions for the grafting of poly($N$-vinyl- 2-pyrrolidone) (PVP) onto the surface of plasma-treated polypropylene film. The plasma treatment conditions were fixed as 200 W rf power, 6 LPM Ar flow rate, 30 sec treatment time, and 5 min exposure time after treatment. For graft copolymerization, we investigated the change of grafting degree with respect to reaction time, reaction temperature and $N$-vinyl-2-pyrrolidone concentration. Maximum grafting degree was obtained at the conditions of 6 h reaction time, $90^{\circ}C$ reaction temperature, and 40% $N$-vinyl-2-pyrrolidone concentration. The introduction of PVP was confirmed by ATR-FTIR, XPS, and SEM analysis.