• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 봄 학술발표회 논문집(I)
• /
• pp.197-202
• /
• 1999

The properties of surface-glossing of exposed concrete with the kinds of form materials and form oil are investigated under various slump value. According to the experimental results, surface-glossing has high value with the increase of slump. In case of surface-glossing with the kind of the form, the form made of acryl has the best performance among the form kinds tested in this experiment. The order of surface-glossing is follows ; fancy plywood > metal form > plywood. Water solution type form oil has better performance in surface-glossing than oil solution type form oil. Also, surface-glossing get worse with the elapse of age.

• 한국건축시공학회지
• /
• 제10권3호
• /
• pp.57-64
• /
• 2010

본 연구는 알루미늄 거푸집 표면코팅재가 콘크리트 표면품질에 미치는 영향에 대하여 분석한 것이다. 콘크리트 표면형상에 미치는 알루미늄 거푸집 표면코팅재 변화의 영향에 따른 콘크리트 표면의 육안관찰시 전반적으로 전용횟수가 증가함에 따라 표면품질은 저하하는 것으로 나타났고, 치장합판(Plywood이하: PW)이 우수한 표면품질을 나타내었다. 에폭시(Epoxy :이하 EP) 수지의 경우는 박리제를 도포하였을 시 표면품질이 우수한 것으로 나타났다. 박리제 도포여부 및 전용횟수에 따른 콘크리트의 표면조도는 전용횟수가 증가함에 따라 가장 높은 표면조도 값을 나타내어 평활성이 불량한 것으로 나타났지만, EP와 PW의 표면조도 값은 가장 우수한 것으로 나타났다. 다만 EP의 경우는 박리제를 도포할 경우 표면조도 값이 낮게 나타났다. 박리제 도포여부 및 전용횟수에 따른 콘크리트의 공극갯수는 전반적으로 박리제를 도포할시 저감하는 것으로 나타났다.

• 대한조선학회논문집
• /
• 제45권6호
• /
• pp.601-610
• /
• 2008

This paper deals with a new geometrical surface modeling method of forebody's hull form which is fully defined by form parameters. The complex hull form in the forebody can be modeled by the combination of three parts: bare hull, bulbous bow and blending part which connects a bare hull and a bulbous bow. All these subdomain parts are characterized by each own form parameters and constructed with simple surface model. For this, we need only 2-dimensional hull form data and then the form parameters are calculated automatically from these data. Finally, the smooth hull form surfaces are generated by parametric design and fair-skinning. In the practical point of view, we show that this new method can be useful and efficient modeling tool by applying to the hull form surface modeling of Panamax container's forebody.

• 콘크리트학회논문집
• /
• 제12권4호
• /
• pp.15-22
• /
• 2000

The objective of this study is to investigate the degree of surface-glossing of flowing concrete, varying with W/C, types of forms and form oils. According to the experimental results, the degree of surface-glossing of flowing concrete is turned out to be higher than that of base concrete, as the slump increases. The degree of surface-glossing of concrete with 40% of W/C is higher than that with 50%. The orders of degree of surface-glossing with the types of forms are as follows : acryle > fancy plywood > metal form > plywood. When water solution type form oil is applied to the surface of forms, we can achieve higher degree of surface-glossing. It shows that the degree of surface-glossing decreases with elapsed time.

• 한국생산제조학회지
• /
• 제9권3호
• /
• pp.111-122
• /
• 2000

It is difficult to make shape library for featrue-based modeling because free-form surface is various shaped complicated To make modeling using similar shape feature-based model is easy and fast. Recently RE(Reverse Engineering) technolo-gy is very convenient method to get free-form surface. This study develops surface editor which makes surface modeling to manipulate control points and this study We study on the effective model data management using database system.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 가을 학술발표회 논문집(II)
• /
• pp.911-914
• /
• 2000

Surface glossing and physical properties of exposed concrete varied with blast furnace slag content are dsicussed in this paper. According to experimental results, as the content of blast furnace slag increases, concrete gains high strength moderately at later stage and surface glossing increase. It shows that glossing decrease with age. Surface glossing shows high as W/B decreases and surface coating is applied. Concrete according to form type shows good results in surface glossing in order for acryl form, fancy form and steel form.

• Design & Manufacturing
• /
• 제17권2호
• /
• pp.15-21
• /
• 2023

In this study, a diamond turning machine and a laser-assisted machining module were utilized for the complex combined cutting of aspheric shapes and fine patterns on the surface of high-hardness brittle material, silicon. The analysis of material's form accuracy and corrective machining was conducted based on key factors such as laser output, rotational speed, feed rate, and cutting depth to achieve form accuracy below 1 ㎛ and surface roughness below 0.1 ㎛. The cutting condition and corrective machining methods were investigated to achieve the desired form accuracy and surface roughness. The rotational speed of the spindle and the linear feed rate of the diamond turning machine were varied in five stages for the cutting condition test. Surface roughness and form accuracy were measured using both a contact surface profilometer and a non-contact surface profilometer. The experimental results revealed a tendency of improved surface roughness with increased rotational speed of the workpiece, and the best surface roughness and form accuracy were observed at a feed rate of 5 mm/min. Furthermore, based on the cutting condition experiments, corrective machining was performed. The experimental results demonstrated an improvement in form accuracy from 0.94 ㎛ to 0.31 ㎛ and a significant reduction in the average value of the surface roughness curve from 0.234 ㎛ to 0.061 ㎛. This research serves as a foundation for future studies focusing on the machinability in relation to laser output parameters.

• 한국컴퓨터그래픽스학회논문지
• /
• 제6권4호
• /
• pp.29-34
• /
• 2000

이 논문에서는 평행이동곡면 (surface of extrusion) 과 임의의 자유곡면 사이의 교차곡선의 구조를 분석하고 이를 계산하는 방법에 대해 설명한다. 평행이동곡면의 이동방향에 대하여 다른 곡면의 윤곽곡선 (silhouette curve) 을 구하고, 이를 평행이동곡면의 기준곡선과 교차시킴으로써 교차곡선의 구조를 분석한다. 또한, 교차곡선이 존재하는 범위와 특이점을 구함으로써 교차곡선 전체를 안정적이고 효율적으로 계산하는 알고리즘을 제시한다.

• 한국건축시공학회지
• /
• 제13권5호
• /
• pp.457-464
• /
• 2013

Traditionally, the material used for the form in reinforced concrete construction has been wood or steel. But recently, aluminum forms have been widely used in wall structures such as apartment buildings. Aluminum is light, easy to handle, and economically advantageous, but the hydrogen gas created due to its reaction with the alkali component in concrete gives rise to air pockets on the concrete's surface, and deteriorates the surface's finishability. In this research, to determine the influence of aluminum material on concrete, the cement paste W/C and its chemical reactivity in alkali and acid solution were analyzed. As a prevention plan, the influence of the number of applications of calcium hydroxide and various surface coating materials was analyzed. Through the analysis, it was found that the surface voids on the aluminum form are the result of the reaction of hydrogen gas with an alkali such as $Ca(OH)_2$. This can be prevented by the surface treatment of $Ca(OH)_2$, separating material and coating material. However, poor surface form and damages to the form are expected to cause quality degradation because of the aluminum-concrete interaction. Therefore, thorough surface treatment, rather than the type of separating material or coating material, is considered the most important target of management.

• 한국기계가공학회지
• /
• 제2권3호
• /
• pp.90-95
• /
• 2003

The W-EDM is very important In precision machining of die, punch and small parts of precision products, so this machining method is widely used in various fields of industry. In this study, machining characteristics of Hand Drum Form and surface roughness are investigated experimentally. As Hand drum form has great effect on straightness of cut-surface of workpiece, its evaluation is very important in precision cutting. As experimental material, the mold material, STD11 is used and machined by CNC wire-EDM using the 025mm wire in diameter with repeated cutting up to 6 times. The thickness of workpiece is vaned in 20, 40, 60, 80, 100mm Hand drum form and surface roughness are measured after each cutting. Experimental results show that four times-cutting is optimum in the point of hand drum form and surface roughness.