• Korean Chemical Engineering Research
• /
• v.48 no.6
• /
• pp.776-783
• /
• 2010

Co and Ni catalysts supported on $Al_2O_3$ for partial oxidation of methane producing hydrogen were synthesized using impregnation to incipient wetness. The activities of these catalysts for the partial oxidation of methane was investigated at 1 atm and $CH_4/O_2=2.0$ in the temperature range of $450{\sim}650^{\circ}C$. The reaction activity of $Ni/Al_2O_3$ and $Co/Al_2O_3$ catalysts with different loading was investigated. And the beneficial effects of Ni addition to $Co/Al_2O_3$ and the promotional effects of Ce and La addition to $Ni/Al_2O_3$ and $Co/Al_2O_3$ were investigated. These catalysts were characterized by XRD and SEM/EDX. Comparing catalyst loadings, 10 wt% Co and 10 wt% Ni were found to be optimal at the experimental conditions. The 10 wt% $Ni/Al_2O_3$ and 10 wt% $Co/Al_2O_3$ catalysts in partial oxidation of methane showed $CH_4$ conversions and CO selectivity close to the thermodynamic equilibrium levels, but showed lower $H_2$ selectivity than equilibrium level. The addition of Ni to $Co/Al_2O_3$ exhibited higher $H_2$ selectivity but beneficial effect was not observed in the $CH_4$ conversion. Addition of Ce to $Co/Al_2O_3$ and addition of La to $Ni/Al_2O_3$ a improved the $CH_4$ conversion level and $H_2$ selectivity.

• Transactions of the Korean hydrogen and new energy society
• /
• v.34 no.5
• /
• pp.421-430
• /
• 2023

Fe-Ni-Pt nanocatalysts were loaded on carbon black powders which were synthesized by a spontaneous reduction reaction of iron (II) acetylacetonate, nickel (II) acetylacetonate and platinum (II) acetylacetonate. The morphology and the loading weight of Fe-Ni-Pt nanoparticles were characterized by transmission electron microscopy and thermogravimetric analyzer. The amount of Fe-Ni-Pt catalyst supported on the carbon black surface was about 6.42-9.28 wt%, and the higher the Fe content and the lower the Pt content, the higher the total amount of the metal catalyst supported. The Brunauer-Emmett-Teller Analysis (BET) specific surface area of carbon black itself without metal nanoparticles supported was 233.9 m²/g, and when metal nanoparticles were introduced, the specific surface area value was greatly reduced. This is because the metal nanocatalyst particles block the pore entrance of the carbon black, and thereby the catalytic activity of the metal catalysts generated inside the pores is reduced. From the I-V curves, as the content of the Pt nanocatalyst increased, the electrolytic properties of water increased, and the activity of the metal nanocatalyst was in the order of Pt > Ni > Fe.

• Applied Chemistry for Engineering
• /
• v.34 no.2
• /
• pp.126-130
• /
• 2023

In response to environmental demands, pyrolysis is one of the practical methods for obtaining reusable oils from waste plastics. However, the waste plastic pyrolysis oils (WPPO) are consumed as low-grade fuel oil due to their impurities. Thus, this study focused on the upgrading method to obtain naphtha catalytic cracking feedstocks from WPPO by the hydroprocessing, including hydrotreating and hydrocracking reaction. Especially, various transition metal sulfides supported catalysts were investigated as hydrotreating and hydrocracking catalysts. The catalytic performance was evaluated with a 250 ml-batch reactor at 370~400 ℃ and 6.0 MPa H₂. Sulfur-, nitrogen-, and chlorine-compounds in WPPO were well eliminated with nickel-molybdenum/alumina catalysts. The NiMo/ZSM-5 catalyst has the highest naphtha yield.

• Journal of the Korean Institute of Gas
• /
• v.13 no.5
• /
• pp.26-32
• /
• 2009

Ni catalysts on mesoporous silica and commercial silica were prepared for the methanation. XRD and TPR analyses indicated that Ni/mesoporous silica had smaller metal particle size and higher metal dispersion than that of Ni/commercial silica. In addition, Ni/mesoporous silica had stronger metal-support interaction. In methanation, Ni/mesoporous silica showed higher CO conversion and methane yield (65%) than Ni/commercial silica (58%). In the characterization results of catalysts after reaction, Ni/commercial silica was deactivated by the collapse of structure and metal sintering, but Ni/mesoporous silica showed stable catalytic performance.

• Journal of the Korean Institute of Gas
• /
• v.13 no.5
• /
• pp.33-38
• /
• 2009

Synthetic natural gas was producd by the reaction of carbon monoxide and hydrogen via methanation. Ni-Co bimetallic catalyst supported on $Al_2O_3$ for methanation was prepared using deposition-precipitation method. For the comparison, Ni, Co monometallic catalyst was prepared using the same method. The prepared catalysts were characterized by TEM, XRD and TPR and applied to methanation reaction. The catalysts prepared using deposition-precipitation method showed the high metal dispersion. The activity of Ni-Co bimetallic catalyst was higher than that of Ni, Co monometallic catalyst. TPR measurements indicated that Ni-Co bimetallic catalyst had more active hydrogen species than Ni, Co monometallic catalyst due to the synergetic effect in the presence of Ni and Co.

• Transactions of the Korean hydrogen and new energy society
• /
• v.15 no.2
• /
• pp.152-158
• /
• 2004

Hydrogen has been considered as an important and essential future energy source. But the storage of the hydrogen is a difficult problem and many studies were focused on this matter. However, the MTH-system (methylcyclohexane, toluene, hydrogen) was proposed for storage of hydrogen by Taube et al. and that is the reaction of hydrogen with toluene to give methylcyclohexane. One toluene molecule can store six hydrogen atoms to form methylcyclohexane. In this form the hydrogen can be easily stored in liquid organic hydrides and transported at ambient pressure in tanks. Hence, this study is focused on the catalytic dehydrogenation of methylcyclohexane. Since supported platinum and nickel were employed as catalysts in literature, in this study, porous Pt and Ni were prepared and tested for the dehydrogenation reaction. When the porous Pt catalyst was applied to the dehydrogenation it showed higher activity in the reaction and higher selectivity to toluene. Specially at higher pressure, it showed almost 100 % conversion and 100 % selectivity and hence porous platinum could be considered as best for the given reaction.

• Transactions of the Korean hydrogen and new energy society
• /
• v.32 no.6
• /
• pp.464-469
• /
• 2021

A reforming catalyst for hydrogen production from ammonia is being studied. Non-novel metal based Ni catalysts for use in ammonia reforming processes are being developed. In this study, the ammonia reforming characteristics according to Ni content of the alumina pellet supported catalyst in the mid-temperature region were investigated under different space velocity. 20 Ni and 3,000 h^-1 showed the best catalytic activity with ammonia conversion of 63% among all conditions.

• Clean Technology
• /
• v.28 no.2
• /
• pp.154-162
• /
• 2022

Microstructured Al@Al₂O₃ and Al@Ni-Al LDH (LDH = layered double hydroxide) core-shell metal-ceramic composites are prepared by hydrothermal reactions of aluminum (Al) metal substrates. Controlled hydrothermal reactions of Al metal substrates induce the hydrothermal dissolution of Al ions at the Al-substrate/solution interface and reconstruction as porous metal-hydroxides on the Al substrate, thereby constructing unique metal-ceramic core-shell composite structures. The morphology, composition, and crystal structure of the core-shell composites are affected largely by the ions in the hydrothermal solution; therefore, the critical physicochemical and surface properties of these unique metal-ceramic core-shell microstructures can be modulated effectively by varying the solution composition. A Ni/Al@Al₂O₃ catalyst with highly dispersed catalytic Ni nanoparticles on an Al@Al₂O₃ core-shell substrate was prepared by a controlled reduction of an Al@Ni-Al LDH core-shell prepared by hydrothermal reactions of Al in nickel nitrate solution. The reduction of Al@Ni-Al LDH leads to the exolution of Ni ions from the LDH shell, thereby constructing the Ni nanoparticles dispersed on the Al@Al₂O₃. The catalytic properties of the Ni/Al@Al₂O₃ catalyst were investigated for CO₂ methanation reactions. The Ni/Al@Al₂O₃ catalyst exhibited 2 times greater CO₂ conversion than a Ni/Al₂O₃ catalyst prepared by conventional incipient wetness impregnation and showed high structural stability. These results demonstrate the high effectiveness of the design and synthesis methods for the metal-ceramic composite catalysts derived by hydrothermal reactions of Al metal substrates.