• 한국가시화정보학회지
• /
• 제9권1호
• /
• pp.55-60
• /
• 2011

Pulsed supersonic liquid jets injected into an ambient air are empirically studied by using a high pressure ballistic range system. Ballistic range systems which are configured with high-pressure tube, pump tube, launch tube and liquid storage nozzle. Experimental studies are conducted to use with various impact nozzle geometry. Supersonic liquid jets are generated by an impact of high speed of the projectile. High speed liquid jets are injected with M = 3.2 which pressure is 1.19 GPa. Multiple jets which accompany with shock wave and pressure wave in front of the jet were observed. The shock-wave affects significantly atomization process for each spray droplets. As decreasing orifice diameter, the averaged SMD of spray jets had the decreasing tendency.

• 한국분무공학회지
• /
• 제17권2호
• /
• pp.86-93
• /
• 2012

The effects of projectile impact system on the transient spray characteristic which is supersonic liquid tip velocity were studied by experimentally. Supersonic liquid jets were generated by impact of a high speed projectile driven by a Two-stage light gas gun. A high speed camera and schlieren optical system were used to capture the spray structures of the supersonic liquid jets. In a case of nozzle assembly Type-A, expansion gases accelerate a projectile which has a mass of 6 grams from 250 m/s at the exit of the launch tube. Accelerated projectile collides with the liquid storage part, then supersonic liquid jets are injected with instantaneous spray tip velocity from 617.78 m/s to 982.54 m/s with various nozzle L/d. However, In a case of nozzle assembly Type-B which has a heavier projectile (60 grams) and lower impact velocity (182 m/s), an impact pressure was decreased. Thus the liquid jet injected at 210 m/s of the maximum velocity did not penetrate a shock wave and fast break-up was occurred. Pulsed injection of liquid column generated second shock wave and multiple shock wave.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2001년도 유체기계 연구개발 발표회 논문집
• /
• pp.149-155
• /
• 2001

Recently, it is required to design higher stage pressure ratio compressor while maintaining equal adiabatic efficiency. To increase the stage pressure ratio, blade rotational speed or diffusion factor should be increased. In the case of increasing rotational speed, relative speed of flow at blade leading edge is well supersonic. In supersonic blade, total pressure loss is mainly due to shock wave and blade leading edge thickness should be very thin to minimize the shock wave loss. As a result, the blade is like to be week in terms of mechanical strength and the manufacturing cost is very high because NC machining is necessary. It is also one of big hurdle to overcome to make small compressor. In this paper, the effects of blade leading edge to the performance of supersonic blade In terms of total pressure loss. The efficiency of already known method to make thin blade leading edge from the casted blade with rather thick leading edge thickness is also assessed.

• Journal of Mechanical Science and Technology
• /
• 제15권12호
• /
• pp.1816-1821
• /
• 2001

Two-dimensional blow-down type supersonic wind tunnel was designed and built to investigate the transient behavior of the startup of a supersonic flow from rest. The contour of the divergent part of the nozzle was determined by the MOC calculation. The converging part of the nozzle, upstream of fille throat was contoured to make the flow uniform at the throat. The flow characteristics of the steady supersonic condition were visualized using the high-speed schlieren photography. The Mach number was evaluated from the oblique shock wave angle on a sharp wedge with halt angle of 5 degree. The measured Mach number was 2.4 and was slightly less than the value predicted by the design calculation. The initial transient behavior of the nozzle was recorded by a high-speed digital video camera with schlieren technique. The measured transition time from standstill to a steady supersonic flow was estimated by analyzing the serial images. Typical transition time was approximately 0.1sec.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2002년도 유체기계 연구개발 발표회 논문집
• /
• pp.227-233
• /
• 2002

It is common for highly loaded supersonic stage to have very high relative inlet Mach number. To get this level of inlet Mach number, rotor blade outer diameter or rotational speed should be increased. In the case of commercial turbo-fan engine, it is preferred to make the rotor blade outer diameter large than increasing the rotational speed. But, for multi-stage fan of military engines, overall diameter is often restricted and they are apt to increase the rotational speed. With high rotational speed, relative inlet Mach number is likely to be well supersonic over the entire rotor blade span and the characteristic of the stage is affected with meridional shape of the stage, especially at near hub or tip. In this paper, the aerodynamic performance of two different hub surface shape is compared and it's merit and demerits were discussed.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.777-780
• /
• 2011

초음속 풍동은 고속으로 운용되는 비행체나 유도무기의 개발에 있어 시험체 주위에서 나타나는 공기역학적 현상을 연구하고 특성을 대표하는 물리량을 측정하기 위해 주로 사용되는 지상시험 장비이다. 본 연구에서는 연구팀에서 보유하고 있는 소형 초음속 풍동이 갖는 시험 모델 크기의 제약을 완화하고자 $250mm{\times}200mm$ 의 시험부를 갖는 초음속 풍동을 설계하고 제작된 풍동의 성능 평가를 수행하였다. 제작된 풍동의 시험 마하수는 2.5이며 시험부에서 균일한 유동을 얻을 수 있도록 경계층 보정을 수행하여 노즐의 형상을 결정하였다.

• 한국산학기술학회논문지
• /
• 제17권11호
• /
• pp.363-367
• /
• 2016

본 연구는 마하수 2.5의 초음속 영역에서 마하수 1.0의 슬롯 분사가 있는 후향계단 형상에 대한 유동장 특성을 분석하기 위하여 초음속풍동 시험부를 설계, 제작하였다. 비행체가 고속으로 움직일 때 공동 주위의 유동은 매우 복잡하여 수치해석 결과를 검증할 초음속풍동 시험 자료가 필요하기 때문에 기존의 2차원 대칭형 노즐을 아랫면이 평판인 비대칭형 노즐로 수정하였다. 특성곡선해법을 이용한 비점성 노즐을 설계하고, 시험을 통해 얻은 경계층 두께를 노즐에 반영하여 보정한 기법을 C 언어로 프로그래밍하여 얻은 결과를 수치해석 결과와 비교하여 검증하였다. 슬롯 분사 시 지속적인 유동장 변화 분석을 위한 초음속 유지시간 확보를 위해 저장탱크의 압력 변화에 따른 PID 제어프로그램 수정으로 초음속 유동 유지시간을 약 5초에서 약 6초로 1초 정도 연장하여 제어 효율을 향상하였고, 슬롯 분사가 있는 후향계단에서의 유동장 변화를 슐리렌장치로 가시화하여 복잡한 유동장 특성을 확인하였다. 향후 슬롯 분사의 속도와 유량, 유동장의 온도를 변화하여 공동에서의 막냉각 효과 분석을 위한 장비로 사용할 계획이다.

• 한국항공우주학회지
• /
• 제35권10호
• /
• pp.899-904
• /
• 2007

전투기급 항공기 개념설계 기간 중 항공기 초음속 순항성능에 미치는 앞전플랩 굽힘 효과를 분석하기 위하여 1/20 축척 날개-동체-꼬리 형상 모형을 사용한 고속 풍동시험을 수행하였다. 풍동시험을 위한 적절한 앞전플랩 각도를 선정하기 위하여 보정된 초음속 패널 방법을 사용하여 다양한 앞전플랩 굽힘 각도에 따른 공력특성을 분석하였다. 실험 및 수치해석적 접근 결과 분석을 기초로, 앞전플랩 굽힘 효과는 전투기급 항공기의 초음속 순항 성능 증대에 유용한 것으로 확인되었다.

• 한국가시화정보학회지
• /
• 제9권2호
• /
• pp.27-33
• /
• 2011

Supersonic liquid jet discharged from a nozzle has been investigated by using a ballistic range which is composed of high-pressure tube, pump tube, launch tube and liquid storage nozzle. High-speed Schlieren optical method was used to visualize the supersonic liquid jet flow field containing shock wave system, and spray droplet diameter was measured by the laser diffraction method. Experiment was performed with various types of nozzle to investigate the major characteristics of the supersonic liquid jet operating at the range of total pressure of 0.8 from 2.14 GPa. The results obtained shows that shock wave considerably affects the detailed atomization process of the liquid jet and as the nozzle diameter decreases, the shock wave angle and the averaged SMD of spray droplet tends to decrease.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.75-78
• /
• 2004

Various jet engines (Turbine engine family and RAM Jet engine) have been developed for high speed aircrafts. but their application to hypersonic flight is restricted by principle problems such as increase of total pressure loss and thermal stress. Therefore, the development of next generation propulsion system for hypersonic aircraft is a very important subject in the aerospace engineering field, SCRAM Jet engine based on a key technology, Supersonic Combustion. is supposed as the best choice for the hypersonic flight. Since Supersonic Combustion requires both rapid ignition and stable flame holding within supersonic air stream, much attention have to be given on the mixing state between air stream and fuel flow. However. the wider diffusion of fuel is expected with less total pressure loss in the supersonic air stream. So. in this study the direction of fuel injection is inclined 30 degree to downstream and the total pressure of jet is controlled for lower penetration height than thickness of boundary layer. Under these flow configuration both streams, fuel and supersonic air stream, would not mix enough. To spread fuel wider into supersonic air an aerodynamic force, baroclinic torque, is adopted. Baroclinic torque is generated by a spatial misalignment between pressure gradient (shock wave plane) and density gradient (mixing layer). A wedge is installed in downstream of injector orifice to induce an oblique shock. The schlieren optical visualization from side transparent wall and the total pressure measurement at exit cross section of combustor estimate how mixing is enhanced by the incidence of shock wave into supersonic boundary layer composed by fuel and air. In this study non-combustionable helium gas is injected with total pressure 0.66㎫ instead of flammable fuel to clarify mixing process. Mach number 1.8. total pressure O.5㎫, total temperature 288K are set up for supersonic air stream.