• Progress in Superconductivity
• /
• v.2 no.1
• /
• pp.39-42
• /
• 2000

The mixed-state Hall angle has been measured in Hg-based superconducting thin films as functions of magnetic fields (H) up to 18 T. The temperature dependence of the Hall angle shows a peak (T*) at low temperature, which is consistent with a crossover point from the thermally activated flux flow (TAFF) to a critical region (CR). At low fields below 10 T, T* shifts to low temperature with increasing fields. Interestingly, however, we found that T* is independent of fields above 10 T, suggesting unusual vortex state. A physical implication of H-T* line will be discussed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.14 no.1
• /
• pp.17-20
• /
• 2004

We derive specific heat gap at the critical temperature as an exact anylitical function of applied magnetic field by using the thermodynamics. And we calculate numerical value of specific heat gap for some superconductors with the derived results and discuss the physical meaning. And it will be discussed that gap of specific heat discontinuity under certain magnetic field intensity become zero at the critical temperature.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.4
• /
• pp.141-144
• /
• 2005

[ $(Y_{0.5}Sm_{0.25}Nd_{0.25})Ba_2Cu_3O_y$ ] [(YSN)-123] high $T_c$ composite superconductors with $CeO_2$ addition were systematically investigated by top seeded melt growth (TSMG) process in air atmosphere. A melt textured $NdBa_2Cu_3O_y$ (Nd-123) single crystal was used as a seed for achieving the c-axis alignment large grains perpendicular to the surface of (YSN)-123 composite oxides. The size of $(Y_{0.5}Sm_{0.25}Nd_{0.25})_2BaCuO_5$ [(YSN)211] nonsuperconducting inclusions of the melt textured (YSN)-123 samples with $CeO_2$ addition were remarkably reduced and uniformly distributed within the (YSN)123 superconducting matrix except in the region very close to the Nd-123 seed crystal. The sample showed a sharp superconducting transition of 91 K.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.573-576
• /
• 2003

HTS superconducting tapes are now commercially available for practical applications such as magnets and cables. Since superconductors in such applications are subjected to high mechanical loads that can significantly degrade the superconducting properties, mechanical properties and the strain tolerance known as the strain effect on superconducting properties are needed to be estimated for developing superconducting devices. Influences of loading mode on the Ic degradation and the interaction on strain effect were discussed in this study.

• Proceedings of the KIEE Conference
• /
• 1990.07a
• /
• pp.254-256
• /
• 1990

We fabricated a high Tc superconducting motor named the "Meissner Motor" using Y system high Tc superconductors, which rotates with the repulsive force caused by the Meissner effect. And, we derived the optimal rotating conditions and parameters from the examination of its chracteristics. Finally the possibility of a high Tc superconducting rotor has been investigated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.05a
• /
• pp.252-255
• /
• 1996

Superconducting current lead is one of the promising applications of the oxide high-Tc superconductors, because they have the advantage of decreasing heat conduction to low temperature region, comparing with a conventional cooper alloy lead. High critical current density is a key factor for the applications such as current lead. (Bi,Pb)$_2$Sr$_2$Ca$_2$Cu$_3$O$\_$x/ high Tc superconductor haute been investigated in terms of critical current density. Bi-2223 superconducting current lead made by CIP and solid state sintering process. Bi-2223 current lead that heat treated at 836$^{\circ}C$ for 240 h in 1/13 P$\_$O$_2$/ had over 150 A/$\textrm{cm}^2$ of critical current density at 77K. We knew that the superconducting properties of tube type current leads were better than rods type of them. And we investigated the relation of Bi-2223 formation and heat treatment condition by XRD and SEM analysis.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1988.05a
• /
• pp.10-12
• /
• 1988

High Tc Y-Ba-Cu-O Superconductors were fabricated by sintering, sintering + HIP and Hot Pressing. Specimens were sintered at $940^{\circ}C$ and $960^{\circ}C$. In case that sintered specimens were treated by HIP, the relative density was increased 5-6% in comparison with sintered ones. X-ray analysis of each specimens represented orthorhombic phase and Tc measurements showed a sharp drop in the temperature range $95-88^{\circ}K$. The relative density of hot pressed samples was lower than 80%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1988.05a
• /
• pp.17-19
• /
• 1988

$YBa_2Cu_3O_{7-x}$ oxide superconductors were fabricated by the hot isostatic pressing (HIP). It was shown that their structures were orthorombic and constited of a single (123) phase. While as-sintered compacts had many pores, they were remarkably reduced by Hiping. The on-set and off set temperature of (123) compound sintered at $950^{\circ}C$ in oxygen and hiping at $880^{\circ}C$ were the highest and it showed 0 resistance at $90^{\circ}K$. The critical current density ($J_c$) of the above superconductor was $27A/cm^2$ and it also showed a number of twin structures, which are typical of high $T_c$ superconductor. It seemed that the low current density may be due to the many pores of starting-sintered compacts.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.924-925
• /
• 1999

Bi-system high-$T_c$ superconductors with the nominal composition $(Bi_{0.7}Pb_{0.3})_2-Sr_{2}Ca_{2}Cu_{3}O_{x}$ have been prepared by PJL method. The critical temperature (offset temperature) of the sample annealed for 13 hours in air was 102K. And the results of X-ray diffraction(XRD) patterns, scanning electron microscope (SEM) images and energy dispersive X-ray (EDX) spectra analyses, it was found that PJL method is so effective to reduce the heat treatment period.

• Progress in Superconductivity
• /
• v.3 no.2
• /
• pp.168-171
• /
• 2002

We have demonstrated ramp-edge Josephson junctions using high temperature superconductors without depositing artificial barriers. We fabricated a surface barrier formed naturally during an ion beam etching process and the annealing under the oxygen atmosphere. The experimental results imply that the barrier natures such as the resistivity are varied by the annealing conditions and the ion milling conditions including the beam voltages. Thus, the ann eating and etching conditions should be optimized to obtain excellent junction properties. In optimizing the fabricating factors, the interface-controlled junctions showed resistively shunted junctions like current-voltage characteristics and an excellent uniformity. These junctions exhibited a spread ($1\sigma$) of $I_{c}$ is 10% fur chips containing 7 junctions at 50K.K.