• Environmental Engineering Research
• /
• v.25 no.3
• /
• pp.316-323
• /
• 2020

The degradation of aqueous oxytetracycline (OTC) from an aqueous solution antibiotic using H₂O₂/Fe²⁺ process was studied in one 1 L batch chemical reactor. The extent of OTC degradation (20 mg/L) was investigated from a known initial pH solution, temperature and the type of catalyst (Fe²⁺, Fe³⁺) and for various initial concentrations of OTC, H₂O₂ and Fe²⁺. The degradation efficiency achieved was found to be very important (90.82% and 90.63%) at initial pH solution of 3 and 4, respectively. However, the type of catalyst and the reaction temperature had a slight impact on the final degradation of OTC. The results showed that the OTC removal increased with increasing initial H₂O₂ concentration in the range of 70 to 150 mg/L and initial Fe²⁺ concentrations in the range of 2 to 5 mg/L. The highest degradation efficiency obtained at ambient temperature was 90.95% with initial concentration of OTC of 10 mg/L, H₂O₂ = 150 mg/L and Fe²⁺ = 5 mg/L. Moreover, biodegradability improved from 0.04 to 0.36 and chemical oxygen demand degradation was 78.35% after 60 min of treatment. This study proved that Fenton process can be used for pretreatment of wastewater contaminated by OTC before a biological treatment.

• Nuclear Engineering and Technology
• /
• v.55 no.4
• /
• pp.1300-1309
• /
• 2023

Simulated debris was synthesized using UO₂, Zr, and stainless steel and a heat treatment method under inert or oxidizing conditions. The primary U solid phase of the debris synthesized at 1473 K under inert conditions was UO₂, whereas a (U, Zr)O₂ solid solution formed at 1873 K. Under oxidizing conditions, a mixture of U₃O₈ and (Fe, Cr)UO₄ phases formed at 1473 K, whereas a (U, Zr)O_2+x solid solution formed at 1873 K. The leaching behavior of the fission products from the simulated debris was evaluated using two methods: the irradiation method, for which fission products were produced via neutron irradiation, and the doping method, for which trace amounts of non-radioactive elements were doped into the debris. The dissolution behavior of U depended on the properties of the debris and aqueous solution for immersion. Cs, Sr, and Ba leached out regardless of the primary solid phases. The leaching of high-valence Eu and Ru ions was suppressed, possibly owing to their solid-solution reaction with or incorporation into the uranium compounds of the simulated debris.

• Membrane and Water Treatment
• /
• v.15 no.1
• /
• pp.21-29
• /
• 2024

1H,1H,2H,2H-perfluorodecytriethoxysilane (C₁₆H₁₉F₁₇O₃Si) be successfully applied to the hydrophobic modification of Al₂O₃ tubular ceramic membrane. Taking the concentration of modification solution, modification time, and modification temperature as factors, orthogonal experiments were designed to study the hydrophobicity of the composite membranes. The experiments showed that the modification time had the greatest impact on the experimental results, followed by the modification temperature, and the modification solution concentration had the smallest impact. Concentration of the modified solution 0.012 mol·L^-1, modification temperature 30 ℃ and modification time 24 h were considered optimal hydrophobic modification conditions. And the pure water flux reached 274.80 kg·m^-2·h^-1 at 0.1MPa before hydrophobic modification, whereas the modified membrane completely blocked liquid water permeation at pressures less than 0.1MPa. Air gap membrane distillation experiments were conducted for NaCl (2wt%) solution, and the maximum flux reached 4.20 kg·m^-2·h^-1, while the retention rate remained above 99.8%. Given the scarcity of freshwater resources in coastal areas, the article proposed a system for seawater desalination using air conditioning waste heat, and conducted preliminary research on its freshwater production performance using Aspen Plus. Finally, the proposed system achieved a freshwater production capacity of 0.61 kg·m^-2·h^-1.

• 전기의세계
• /
• v.22 no.1
• /
• pp.28-34
• /
• 1973

This paper treats with the sub-optimal control problem of noninear systems by approximation method. This method involves the approximation by linearization which provides the sub-optimal solution of non-linear control problems. The result of this work shows that, in the problem in which the controlled plant is characterized by an ordinary differential equation of first order, the solution obtained by this method coincides with the exact solution of problem. In of case of the second or higher order systems, it is proved analytically that this method of linearization produces the sub-optimal solution of the given problem. It is also shown that the sub-optimality of solution by the method can be evaluated by introducing the upper and lower bounded performance indices. Discussion is made on the procedure with some illustrative examples whose performance indices are given in the quadratic forms.

• Journal of Power System Engineering
• /
• v.20 no.5
• /
• pp.20-28
• /
• 2016

This study has developed an organic/inorganic hybrid solution by addition of $SiO_2$ polysilicate and Melamine to the urethane. The three types of cold rolled steel were evaluated a corrosion resistance properties by using these solutions. The urethane solution(U) and the urethane solution with $SiO_2$ polysilicate($US_7$) were generate a lot of corrosion. The urethane solution with $SiO_2$ polysilicate and melamine($US_7M_3$) was excellent in corrosion resistance, regardless of the steel type. In addition, corrosion resistance has been shown to depend on the tensile strength. The appearance of coating by U and $US_7$ solution is bumpy surface, and were a lot of fine defects. $US_7M_3$ solution is made a sophisticated molecular cross-linking structure inside the coating, it was a slick surface. Other characteristics are exhibited the excellent property for all solutions.

• Corrosion Science and Technology
• /
• v.20 no.5
• /
• pp.289-294
• /
• 2021

In this study, after measuring polarization characteristics of 97.3 wt% Ag, Au-Coated 97.3 wt% Ag (ACA) and 100 wt% Au wires in 1 wt% H₂SO₄ and 1 wt% HCl electrolytes at 25 ℃, corrosion rate and corrosion characteristics were comparatively analyzed. Comparing corrosion potential (E_CORR) values in sulfuric acid solution, ACA wire had more than six times higher E_CORR value than Au wire. Thus, it seems possible to use a broad applied voltage range of bonding wire for semiconductor packaging which ACA wire could be substituted for the Au wire. However, since the E_CORR value of ACA wire was three times lower than that of the Au wire in a hydrochloric acid solution, it was judged that the use range of the applied voltage and current of the bonding wire should be considered. In hydrochloric acid solution, 97.3 wt% Ag wire showed the highest corrosion rate, while ACA and Au showed similar corrosion rates. Additionally, in the case of sulfuric acid solution, all three types showed lower corrosion rates than those under the hydrochloric acid solution environment. The corrosion rate was higher in the order of 97.3 wt% Ag > ACA > 100 wt% Au wires.

• Clean Technology
• /
• v.28 no.2
• /
• pp.154-162
• /
• 2022

Microstructured Al@Al₂O₃ and Al@Ni-Al LDH (LDH = layered double hydroxide) core-shell metal-ceramic composites are prepared by hydrothermal reactions of aluminum (Al) metal substrates. Controlled hydrothermal reactions of Al metal substrates induce the hydrothermal dissolution of Al ions at the Al-substrate/solution interface and reconstruction as porous metal-hydroxides on the Al substrate, thereby constructing unique metal-ceramic core-shell composite structures. The morphology, composition, and crystal structure of the core-shell composites are affected largely by the ions in the hydrothermal solution; therefore, the critical physicochemical and surface properties of these unique metal-ceramic core-shell microstructures can be modulated effectively by varying the solution composition. A Ni/Al@Al₂O₃ catalyst with highly dispersed catalytic Ni nanoparticles on an Al@Al₂O₃ core-shell substrate was prepared by a controlled reduction of an Al@Ni-Al LDH core-shell prepared by hydrothermal reactions of Al in nickel nitrate solution. The reduction of Al@Ni-Al LDH leads to the exolution of Ni ions from the LDH shell, thereby constructing the Ni nanoparticles dispersed on the Al@Al₂O₃. The catalytic properties of the Ni/Al@Al₂O₃ catalyst were investigated for CO₂ methanation reactions. The Ni/Al@Al₂O₃ catalyst exhibited 2 times greater CO₂ conversion than a Ni/Al₂O₃ catalyst prepared by conventional incipient wetness impregnation and showed high structural stability. These results demonstrate the high effectiveness of the design and synthesis methods for the metal-ceramic composite catalysts derived by hydrothermal reactions of Al metal substrates.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.9 no.3
• /
• pp.131-139
• /
• 2011

This study was carried out to examine the stability of $Na_2CO_3-H_2O_2$ carbonate solution with aging time in the dissolving solution after oxidative dissolution of U by a carbonate solution, the Cs/Re filtrate after selective precipitation of Cs and Re (as a surrogate for Tc), and the acidification filtrate after precipitation of U by acidification, respectively. The compositions of dissolving solution were not changed with ageing time, and the selective precipitation of Re and Cs was also not affected without regard to the aging time of dissolving solution. The successive removal of Cs and Re from a carbonate dissolving solution was possible. However, the recovery yield of U by acidification was decreased with increasing the aging time of the dissolving solution and the Cs/Re-filtrate, respectively, because U was converted from the uranyl peroxocarbonato complex to the uranyltricarbonate in the solution aged for a long time. Accordingly, it is effective that a dissolving solution and a Cs/Re filtrate are treated within the aging of 7 days, respectively, in order to recover U more than 99%. On the other hand, the recovery of U was carried out in order of the oxidative dissolution of U selective precipitation of Re and Cs precipitation of U by acidification. Almost all of U and a part of FP were co-dissolved in oxidative dissolution step. Over 99% of Re and Cs from the FP co-dissolved with U could be removed by a TPPCl (tetraphenylphosphonium chloride) and a NaTPB (sodium tetraphenylborate), respectively. U was precipitated nearly 100% by acidification to pH 4. Therefore, it was confirmed that the validity of recovery of U by precipitation methods from a SF (spent fuel) in the $Na_2CO_3-H_2O_2$ solution.

• Resources Recycling
• /
• v.30 no.4
• /
• pp.11-19
• /
• 2021

Arsenic (As) oxidation followed by precipitation from a high-As(III)-containing leaching solution derived from a sulfidic ore was investigated in this study to remove aqueous As from the solution using activated carbon (AC) with air injection as an oxidant. To obtain the initial leaching solution, a domestic sulfidic ore was leached in a sulfuric acid solution at pH 1 and 50℃ for 95 h, and approximately 7 g/L of Fe and 3 g/L of As were leached out. To determine the effect of the oxidative reaction utilizing AC with air injection, the leaching solution was tested under the following five oxidative conditions at an initial pH of 1 and 90℃ for 72 h: air-only injection; air injection with 1, 5, and 10 w/v% of AC addition; and H₂O₂ addition. The tests in the presence of both air and AC revealed that the oxidation kinetics and As removal were improved by the reaction between the metallic species and the surface group formed on the AC surface. In addition, the greater the amount of AC added, the better was the reaction efficiency, removing 93-94% of As with more than 5 w/v% of AC addition. Finally, X-ray diffraction analysis confirmed that the precipitate formed from the oxidative reaction was scorodite (FeAsO₄·2H₂O).

• Journal of the Korean Society for Heat Treatment
• /
• v.35 no.1
• /
• pp.1-7
• /
• 2022

In this study, dissolution and melting phenomenon of the Al₂Cu was studied for the high-strength Al-Si-Cu aluminum alloy in automobile component. The Solution heat treatment was performed at 480℃ and 510℃ for 4hours. Microstructure analysis of the specimen was performed using the optical micrograph and scanning electron microscope for qualitative and quantitative analysis of various phases, the chemical composition of secondary phases was achieved by energy dispersive spectroscopy (EDS) and electron probe micro analysis (EPMA). As a result of the electron probe micro analysis, a plate like Al₂Cu phase was observed, and eutectic Si phase was observed of a coarsen plate shape. At a temperature of 510, necking phenomenon occurs in a specific part of plate like Al₂Cu, and it is segmented and dissolved in the Al matrix. When the temperature of the alloy exceeds the melting point of Al₂Cu, incipient melting occurs at the grain boundary of undissolved Cu particles