• Korean Journal of Materials Research
• /
• v.31 no.11
• /
• pp.649-656
• /
• 2021

K_0.5Bi_0.5TiO₃ (KBT) thin films were prepared by sol-gel processing for future use in piezoelectric generators. It is believed that the annealing temperature of films plays an important role in the output performance of piezoelectric generators. KBT films prepared on Ni substrates were annealed at 500 ~ 700 ℃. Tetragonal KBT films were formed after annealing process. As the annealing temperature increased, the grain size of KBT films increased. KBT thin films show piezoelectric constant (d₃₃) from 23 to 41 pC/N. The increase of grain size in KBT films brought about output voltage and current in the KBT generators. Also, the increase in the displacement of specimens during bending test resulted in increases in output voltage and current. Although KBT generators showed lower output power than those of generators prepared using NBT films, as reported previously, the KBT films prepared by sol-gel method show applicability as piezoelectric thin films for lead-free nano-generators, along with NBT films.

• Korean Journal of Materials Research
• /
• v.34 no.4
• /
• pp.185-193
• /
• 2024

In this study, NASICON-type Li_1+XGa_XTi_2-X(PO₄)₃ (x = 0.1, 0.3 and 0.4) solid-state electrolytes for all-solid-state batteries were synthesized through the sol-gel method. In addition, the influence on the ion conductivity of solid-state electrolytes when partially substituted for Ti⁴⁺ (0.61Å) site to Ga³⁺ (0.62Å) of trivalent cations was investigated. The obtained precursor was heat treated at 450 ℃, and a single crystalline phase of Li_1+XGa_XTi_2-X(PO₄)₃ systems was obtained at a calcination temperature above 650 ℃. Additionally, the calcinated powders were pelletized and sintered at temperatures from 800 ℃ to 1,000 ℃ at 100 ℃ intervals. The synthesized powder and sintered bodies of Li_1+XGa_XTi_2-X(PO₄)₃ were characterized using TG-DTA, XRD, XPS and FE-SEM. The ionic conduction properties as solid-state electrolytes were investigated by AC impedance. As a result, Li_1+XGa_XTi_2-X(PO₄)₃ was successfully produced in all cases. However, a GaPO₄ impurity was formed due to the high sintering temperatures and high Ga content. The crystallinity of Li_1+XGa_XTi_2-X(PO₄)₃ increased with the sintering temperature as evidenced by FE-SEM observations, which demonstrated that the edges of the larger cube-shaped grains become sharper with increases in the sintering temperature. In samples with high sintering temperatures at 1,000 ℃ and high Ga content above 0.3, coarsening of grains occurred. This resulted in the formation of many grain boundaries, leading to low sinterability. These two factors, the impurity and grain boundary, have an enormous impact on the properties of Li_1+XGa_XTi_2-X(PO₄)₃. The Li_1.3Ga_0.3Ti_1.7(PO₄)₃ pellet sintered at 900 ℃ was denser than those sintered at other conditions, showing the highest total ion conductivity of 7.66 × 10^-5 S/cm at room temperature. The total activation energy of Li-ion transport for the Li_1.3Ga_0.3Ti_1.7(PO₄)₃ solid-state electrolyte was estimated to be as low as 0.36 eV. Although the Li_1+XGa_XTi_2-X(PO₄)₃ sintered at 1,000 ℃ had a relatively high apparent density, it had less total ionic conductivity due to an increase in the grain-boundary resistance with coarse grains.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.7
• /
• pp.428-432
• /
• 2015

Sintering and microwave dielectric properties of $Zn_{2-2x}Si_{1+x}O_4$ (x=0~0.10) ceramics were investigated. The secondary phase of ZnO was observed in the specimen for x=0 whereas $SiO_2$ was detected in that for x=0.05. The composition of $Zn_2SiO_4$ might be close to x=0.02, i.e., $Zn_{1.96}Si_{1.02}O_4$; the ratio of Zn/Si is 1.922. The insufficient grain growth was observed in the specimen of x=0. For the specimens of $x{\geq}0.05$, the grain growth sufficiently occurred through the liquid phase sintering. The value of quality factor of all specimens was dependent on the x value, i.e., the ratio of Zn/Si, whereas that of dielectric constant was independent. Relative density, dielectric constant, and quality factor ($Q{\times}f$) of the specimen for x=0.05, i.e., $Zn_{1.9}Si_{1.05}O_4$, sintered at $1,400^{\circ}C$ were 96.5%, 6.43, and 115,166 GHz, respectively.

• The Plant Pathology Journal
• /
• v.36 no.1
• /
• pp.54-66
• /
• 2020

This study was conducted to evaluate usefulness of numerical weather prediction data generated by the Unified Model (UM) for plant disease forecast. Using the UM06- and UM18-predicted weather data, which were released at 0600 and 1800 Universal Time Coordinated (UTC), respectively, by the Korea Meteorological Administration (KMA), disease forecast on bacterial grain rot (BGR) of rice was examined as compared with the model output based on the automated weather stations (AWS)-observed weather data. We analyzed performance of BGRcast based on the UM-predicted and the AWS-observed daily minimum temperature and average relative humidity in 2014 and 2015 from 29 locations representing major rice growing areas in Korea using regression analysis and two-way contingency table analysis. Temporal changes in weather conduciveness at two locations in 2014 were also analyzed with regard to daily weather conduciveness (C_i) and the 20-day and 7-day moving averages of C_i for the inoculum build-up phase (C_inc) prior to the panicle emergence of rice plants and the infection phase (C_inf) during the heading stage of rice plants, respectively. Based on C_inc and C_inf, we were able to obtain the same disease warnings at all locations regardless of the sources of weather data. In conclusion, the numerical weather prediction data from KMA could be reliable to apply as input data for plant disease forecast models. Weather prediction data would facilitate applications of weather-driven disease models for better disease management. Crop growers would have better options for disease control including both protective and curative measures when weather prediction data are used for disease warning.

• Journal of Powder Materials
• /
• v.19 no.4
• /
• pp.253-258
• /
• 2012

The characteristics of $Al_2TiO_5$ ceramics were influenced by the additives and the heat treatment that controls the microcrack behavior at grain boundaries. The effect of additives on $Al_2TiO_5$ ceramics were investigated in terms of mechanical properties and thermal expansion at high temperature. The $Al_2TiO_5$ were synthesized at $1500^{\circ}C$, $1550^{\circ}C$ and $1600^{\circ}C$ for 2h by reaction sintering. The formation of $Al_2TiO_5$ phase was increased by additives that enhanced the volume of the microcrack that can lead to low thermal expansion. The mechanical properties of the stabilized $Al_2TiO_5$ ceramics were increased remarkably at $1100^{\circ}C$, $1200^{\circ}C$ and $1300^{\circ}C$ due to the oneset of mechanical healing of grain-bondary microcracks at a high temperature. The amount of microcrack was decreased at lower sintering temperature that causes the increase of mechanical properties at high temperature.

• Transactions of Materials Processing
• /
• v.31 no.5
• /
• pp.253-260
• /
• 2022

In this study, the microstructural characteristics of a high-speed-extruded Mg-5Bi-3Al (BA53) alloy and its tensile, compressive, and high-cycle fatigue properties are investigated. The BA53 alloy is successfully extruded at a die-exit speed of 16.6 m/min without any hot cracking using a large-scale extruder for mass production. The homogenized BA53 billet has a large grain size of ~900 ㎛ and it contains fine and coarse Mg₃Bi₂ particles. The extruded BA53 alloy has a fully recrystallized microstructure with an average grain size of 33.8 ㎛ owing to the occurrence of complete dynamic recrystallization during high-speed extrusion. In addition, the extruded BA53 alloy contains numerous fine lath-type Mg₃Bi₂ particles, which are formed through static precipitation during air cooling after exiting the extrusion die. The extruded BA53 alloy has a high tensile yield strength of 175.1 MPa and ultimate tensile strength of 244.4 MPa, which are mainly attributed to the relative fine grain size and numerous fine particles. The compressive yield strength (93.4 MPa) of the extruded BA53 alloy is lower than its tensile yield strength, resulting in a tension-compression yield asymmetry of 0.53. High-cycle fatigue test results reveal that the extruded BA53 alloy has a fatigue strength of 110 MPa and fatigue cracks initiate at the surface of fatigue test specimens, indicating that the Mg₃Bi₂ particles do not act as fatigue crack initiation sites. Furthermore, the extruded BA53 alloy exhibits a higher fatigue ratio of 0.45 than other commercial extruded Mg-Al-Zn-based alloys.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.5
• /
• pp.406-411
• /
• 2002

Ni-Zn ferrite is required to have predominant and stable characteristics in the range of high frequency for the power line communication, so that microstructures and magnetic properties such as power loss and initial permeability in $Ni_{0.8}Zn_{0.2}Fe_2O_4$ were investigated in terms of variable $Bi_2O_3,CaO$ and $V_2O_5$ contents. $Bi_2O_3$ and $V_2O_5$ liquid phase created during sintering process promoted sintering and grain growth but much of the closed pore existed in the grains. The grain size of the specimens with $V_2O_5$ of over 0.5 wt% decreased as the result of "pinning effect"and the resonance frequency increased with CaO of 0.3we%. The high initial permeability of 81.52%, resonance frequency of 17.05 MHz and low power loss of 17,858 kW/$\textrm{m}^3$ were obtained from the samples with $Bi_2O_3$ of 0.5, CaO of 0.3, and $V_2O_5$ of 0.7 wt%.

• Korean Journal of Materials Research
• /
• v.26 no.2
• /
• pp.90-94
• /
• 2016

In this study, to increase the strength and enhance the sintering property of $Al_2O_3$, $Y_2O_3$ and $La_2O_3$ were added; the effects of these additions on the sintering characteristics of $Al_2O_3$ were observed. Adding 1% of $Y_2O_3$ to $Al_2O_3$ repressed the development of abnormal particles and reduced the grain boundary migration of $Al_2O_3$, curbing pores to capture particles; as such, the material showed a fine microstructure. But, when over 2% of $Y_2O_3$ was added, the sintering property was reduced because of abnormal particle grain growth and pore formation in particles. Adding 1% of $Y_2O_3$ and $La_2O_3$ to $Al_2O_3$ led to the development of abnormal particles and formed pores in the particles; when over 3% of $La_2O_3$ was added, the sintering property was reduced because the shape of the $Al_2O_3$ particles changed to angled plates.

• Nuclear Engineering and Technology
• /
• v.53 no.5
• /
• pp.1593-1601
• /
• 2021

Oxide dispersion strengthening (ODS) tungsten alloys are highly desirable in irradiation applications. However, how to improve the properties of ODS-tungsten alloys efficiently has been worth studying for a long time. Here we report a nanostructuring approach that achieves W-La₂O₃ alloy with a high level of flexural strength and Vickers hardness at room temperature, which have the maximum value of 581 MPa and 703 Hv, respectively. This method named solution combustion synthesis (SCS) can generate 30 nm coating structures W-La₂O₃ composite powders by using Keggin-type structural polyoxometalates as raw materials in a fast and low-cost process. The composite powder can be fabricated to W-La₂O₃ alloy with an optimal microstructure of submicrometric W grains coexisting with nanometric oxide particles in the grain interior, and a stability interface structure of grain boundaries (GBs) by forming transition zones. The method can be used to prepare new ODS alloys with excellent properties in the future.

• Progress in Superconductivity and Cryogenics
• /
• v.19 no.1
• /
• pp.30-35
• /
• 2017

The effects of the crystallographic orientation and sample thickness on the magnetic levitation forces (F) and trapped magnetic field (B) of single grain YBCO bulk superconductors were examined. Single grain YBCO samples with a (001), (110) or (100) surface were used as the test samples. The samples used for the force-distance (F-d) measurement were cooled at 77 K without a magnetic field (zero field cooling, ZFC), whereas the samples used for the B measurement were cooled under the external magnetic field of a Nd-B-Fe permanent magnet (field cooling, FC). It was found that F and B of the (001) surface were higher than those of the (110) or (100) surface, which is attributed to the higher critical current density ($J_c$) of the (001) surface. For the (001) samples with t=5-18 mm, the maximum magnetic levitation forces ($F_{max}s$) of the ZFC samples were larger than 40 N. About 80% of the applied magnetic field was trapped in the FC samples. However, the F and B decreased rapidly as t decreased below 5 mm. There exists a critical sample thickness (t=5 mm for the experimental condition of this study) for maintaining the large levitation/trapping properties, which is dependent on the material properties and magnitude of the external magnetic fields.