• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.2
• /
• pp.102-107
• /
• 2003

This study puts focus on the optimization of growth temperature of CIGS absorber layer which affects severely the performance of solar cells. The CIGS absorber layers were prepared by three-stage co-evaporation of metal elements in the order of In-Ga-Se. The effect of the growth temperature of 1st stage was found not to be so important, and 350$^{\circ}C$ to be the lowest optimum temperature. In the case of growth temperature at 2nd/3rd stage, the optimum temperature was revealed to be 550$^{\circ}C$. The XRD results of CIGS films showed a strong (112) preferred orientation and the Raman spectra of CIGS films showed only the Al mode peak at 173cm$\^$-1/. Scanning electron microscopy results revealed very small grains at 2nd/3rd stage growth temperature of 480$^{\circ}C$. At higher temperatures, the grain size increased together with a reduction in the number of the voids. The optimization of experimental parameters above mentioned, through the repeated fabrication and characterization of unit layers and devices, led to the highest conversion efficiency of 15.4% from CIGS-based thin film solar cell with a structure of Al/ZnO/CdS/CIGS/Mo/glass.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.12
• /
• pp.815-819
• /
• 2014

Aluminum nitride (AlN) thin film and TiN film as a buffer layer were deposited on INCONEL 600 substrate by reactive RF magnetron sputtering at room temperature(R.T.) under 25~75% $N_2/Ar$ atmosphere. The as-deposited AlN films at 25~50% $N_2/Ar$ showed a polycrystalline phase of hexagonal AlN, and an amorphous phase. The peak of AlN (002) plane, which was determinant on a performance of piezoelectric transducer, became strong with increasing the $N_2/Ar$ ratio. Any change in the preferential orientation of the as-deposited AlN films was not observed within our $N_2$ concentration range. The piezoelectric sensing properties of AlN module were performed using pressure-voltage measurement system. The output signal voltage of AlN module showed a linear behavior between 20~80 mV in 1~10 MPa range, and the pressure-sensing sensitivity was calculated as 3.6 mV/MPa.

• Korean Journal of Food Science and Technology
• /
• v.33 no.3
• /
• pp.389-394
• /
• 2001

In order to isolate antimicrobial substances from Schizandra chinensis, the dried fruits were extracted with the methanol and the extract showed a strong antimicrobial activity. Also, the methanol exract was further fractionated with hexane, dichloromethane, ethylacetate and buthanol. The ethyl acetate-soluble fraction showed the strongest antimicrobial activity. These fraction were further separated by using various chromatographic methods including thin layer chromatography, silicagel open column chromatography and prep. HPLC. A major component S-EA-5-T1 and S-EA-5-T3 from the ethyl acetate fraction, which showed a strong antimicrobial activity was identified by Mass and NMR spectrometry. Two compounds were isolated and identified as trimethylcitrate and the essential oil of Schizandra chinensis and was estimated as gomisin C, respectively. The growth of S. typhimurium was also inhibited about 1.65 to 2.86 log cycle in minced pork by the addition 1% of Schizandra chinensis extract for 12 days at $4^{\circ}C$. These results suggested that these compounds have a strong potential as a natual food preservatives.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.23 no.2
• /
• pp.251-260
• /
• 1994

Lipophilic brown pigments produced during the fermentation of domestic Meju and Doenjang were fractionated by column and thin -layer chromatography (TLC). Each of the fractions was tested for the antioxidant activity and then characterized by spectroscopic analysis. The lipophilic brown pigments were separated into chloroform -soluble and methanol-soluble parts in which Meju resulted the higher content of chloroform-soluble part than that of methanol-soluble part ; however, Doenjang exhibited the opposite result to that of Meju. More strong antioxidant activity was found in the methanol-soluble part than the chloroform-soluble part. Four and five fractions were separated from chloroform-soluble and methanol-soluble parts respectively. by silicagel TLC. The fraction that exhibited the high antioxidant activity showed a strong absorption at 260nm caused by amino compounds in UV spectrum The other fractions which did not have antioxidant activity absorbed at 240nm by carbonic acid and it ester,. IR spectrum of each fraction commonly showed absorption at 3400cm-1 , 2800cm-1 , 1700cm-1, 1600cm-1, 1400cm-1 , 1300cm-1 and 1100cm-1. Especially , the fraction which had a strong antioxidant activity showed absorption at 2800cm-1, 1400cm-1, 1600cm-1 suggesting that the fraction contain Schiff's base and primary amine structure.

• Korean Journal of Food Science and Technology
• /
• v.35 no.4
• /
• pp.726-732
• /
• 2003

The crude extracts from Rhus javanica Linne showed comparatively strong antioxidative activity in test oils. Antioxidative components were isolated and identified by column chromatography, thin layer chromatography, UV, and NMR. These antioxidative components were added to several oils to compare antioxidative activity with several commercial antioxidants, such as BHA, BHT, and tocopherol. After the sixth column chromatography, one fraction (R-18-9-3-2-4-2) was separated from chloroform layer of Rhus javanica Linne. The R-18-9-3-2-4-2 fraction was identified as methyl gallate by $^1H-NMR$ and $^{13}C-NMR$ and confirmed with methyl gallate standard as authentic. The R18-9-3-2-4-2 fraction from chloroform layer of Rhus javanica Linne showed stronger activity than that of the ${\alpha}-,\;{\delta}-tocopherol$, BHT, and BHA at the same concentration.

• Korean Journal of Metals and Materials
• /
• v.46 no.11
• /
• pp.730-736
• /
• 2008

$TiO_2$ nanotubes fabricated in aqueous HF-based electrolytes have been generally grown only to about 500nm in length because of the strong dissolubility of HF acid. In this paper, ethylene glycol solution has been applied for increasing the length of the anodic $TiO_2$ nanotubes, and the growth behaviors of the nanotubes according to water contents has been investigated. Anodization of Ti in ethylene glycol + 1 wt% $NH_4F$ (EG solution) with water additions up to 10 wt% were carried out at the constant voltage of 20 V. The results show that a thin titanium oxide layer is formed in the initial stage and the nanotube structure grows underneath the initial layer. And the length of $TiO_2$ nanotubes decreases with the increasing water content in the solution. It can be ascribed to the locally acidified circumstance around the barrier layer inside the nanopore due to $H^+$ ion originated from water. The XPS for the nanotubes suggests that the spectra of Ti2p and O1s are the major chemical bonding states of the $TiO_2$, and those for F1s, N1s and C1s come from the compound of $(NH_4)_2TiF_6$.

• Journal of Sensor Science and Technology
• /
• v.7 no.1
• /
• pp.67-72
• /
• 1998

The crystallized CuPc and PbTe films are formed by thermal evaporation and pulsed ArF excimer laser ablation. Structural and electrical properties of thin film is observed by XRD and current-voltage(I-V) curves. From XRD analysis, both PbTe and CuPc thin films show a-axis oriented structure. For the measurement of photovoltaic effect, the transverse current-voltage curve of CuPc/Si, PbTe/Si and PbTe/CuPc/Si junctions have been analyzed in the dark and under illumination. The PbTe/CuPc/Si junction exthibits a strong photovoltaic characteristics with short circuit current($J_{sc}$) of $25.46\;mA/cm^{2}$ and open-circuit voltage($V_{oc}$) of 170 mV. Quantum efficiency and power conversion efficiency are calculated to be 15.4% and $3.46{\times}10^{-2}$, respectively. Based on the results of QE and ${\eta}$, the photocurrent process of PbTe/CuPc/Si junction can be explained as following three effective steps; photocarrier generation in the CuPc layer, carrier separation at PbTe/CuPc interface, and finally a transportation of electrons through the PbTe layer.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.643-646
• /
• 2005

The gas hydrate exploration using seismic reflection data, the detection of BSR(Bottom Simulating Reflector) on the seismic section is the most important work flow because the BSR have been interpreted as being formed at the base of a gas hydrate zone. Usually, BSR has some dominant qualitative characteristics on seismic section i.e. Wavelet phase reversal compare to sea bottom signal, Parallel layer with sea bottom, Strong amplitude, Masking phenomenon above the BSR, Cross bedding with other geological layer. Even though a BSR can be selected on seismic section with these guidance, it is not enough to conform as being true BSR. Some other available methods for verifying the BSR with reliable analysis quantitatively i.e. Interval velocity analysis, AVO(Amplitude Variation with Offset)analysis etc. Usually, AVO analysis can be divided by three main parts. The first part is AVO analysis, the second is AVO modeling and the last is AVO inversion. AVO analysis is unique method for detecting the free gas zone on seismic section directly. Therefore it can be a kind of useful analysis method for discriminating true BSR, which might arise from an Possion ratio contrast between high velocity layer, partially hydrated sediment and low velocity layer, water saturated gas sediment. During the AVO interpretation, as the AVO response can be changed depend upon the water saturation ratio, it is confused to discriminate the AVO response of gas layer from dry layer. In that case, the AVO modeling is necessary to generate synthetic seismogram comparing with real data. It can be available to make conclusions from correspondence or lack of correspondence between the two seismograms. AVO inversion process is the method for driving a geological model by iterative operation that the result ing synthetic seismogram matches to real data seismogram wi thin some tolerance level. AVO inversion is a topic of current research and for now there is no general consensus on how the process should be done or even whether is valid for standard seismic data. Unfortunately, there are no well log data acquired from gas hydrate exploration area in Korea. Instead of that data, well log data and seismic data acquired from gas sand area located nearby the gas hydrate exploration area is used to AVO analysis, As the results of AVO modeling, type III AVO anomaly confirmed on the gas sand layer. The Castagna's equation constant value for estimating the S-wave velocity are evaluated as A=0.86190, B=-3845.14431 respectively and water saturation ratio is $50\%$. To calculate the reflection coefficient of synthetic seismogram, the Zoeppritz equation is used. For AVO inversion process, the dataset provided by Hampson-Rushell CO. is used.

• Korean Journal of Food Science and Technology
• /
• v.36 no.6
• /
• pp.1001-1007
• /
• 2004

Chloroform layer from methanol extract of Corni fructus (Cornaceae) showed strong antiproliferation effect on human cancer cell lines by SRB assay. Anticarcinogenic-active compound was isolated and purified by silica gel column and thin layer chromatograpies, and identified as ursolic acid ($3{\beta}$-hydroxyrus-12-ene-28-oic acid, MW:456) by mass and IR spectrophotometries, and $^1H-and\;^{13}C-NMRs$. The compound inhibited proliferation of A549 (human lung cancer cell line) and MCF-7 (human breast cancer cell line) cells in dose-dependant manner when treated for 48 hr. Inhibition rates of both cells were over 40% and 90% compared with control cells at the $30\;{\mu}g/mL\;and\;100\;{\mu}g/mL$, respectively. Morphology of cells treated with the compound for 15 hr at $10\;{\mu}g/mL$ was distorted with shrinked cell mass, and cell number was lower than that of control cells. Cell cycle analysis showed sub-G1 phase arrest in both cell lines following 15 hr exposure to the compound; % of cell phase increased to 11.7 and 11.2% compared to the control of 4.0% and 2.1% in A549 and MCP-7 cells, respectively.

• Korean Journal of Materials Research
• /
• v.14 no.8
• /
• pp.542-546
• /
• 2004

We report a new fabrication process for high performance triode type CNT field emitters and their superior electrical properties. The CNT-based triode-type field emitter structure was fabricated by the conventional semiconductor processes. The keys of the fabrication process are spin-on-glass coating and trim-and-leveling of the carbon nanotubes grown in trench structures by employing a chemical mechanical polishing process. They lead to strong adhesion and a uniform distance from the carbon nanotube tips to the electrode. The measured emission property of the arrays showed a remarkably uniform and high current density. The gate leakage current could be remarkably reduced by coating of thin $SiO_{2}$ insulating layer over the gate metal. The field enhancement factor(${\beta}$) and emission area(${\alpha}$) were calculated from the F-N plot. This process can be applicable to fabrication of high power CNT vacuum transistors with good electrical performance.