• 제목/요약/키워드: stress ratio

검색결과 4,030건 처리시간 0.032초

Investigation of Bottom Cracks in the Carbonated Poly(ethylene terephthalate) Bottle

  • Pae, You-Lee;Nah, Chang-Woon;Lyu, Min-Young
    • Elastomers and Composites
    • /
    • 제38권4호
    • /
    • pp.354-362
    • /
    • 2003
  • The use of a petaloid design for the bottom of carbonated poly(ethylene terephthalate)(PET) bottles is widely spread. This study investigated the causes of bottom cracks. The tensile yield stress variations of PET according to the crystallinity and stretch ratio were examined, then the stretch ratio and strength in the bottom area of a blown bottle were analyzed. A crack test was also performed to observe the cracking phenomena. The distribution of the effective stress and maximum principal stress were both examined using computer simulation to seek the influence of the bottom design on crack. It was concluded that the bottom cracks occurred because of inadequate material strength due to the insufficient stretching of PET, plus the coarse design of a petaloid bottom. The stretch ratio at the bottom during bottle blowing should be higher than the strain hardening point of PET to produce enhanced mechanical strength. The cracks in the bottom of the PET bottles occurred through crazing below the yield stress. The maximum principal stress was higher in the valleys of the petaloid bottom than in the rest bottom area, and the maximum principal stress had a strong effect on the cracks.

연약지반 보강을 위한 저유동성 몰탈 개량체의 응력분담비에 관한 연구 (The Study on the Stress Concentration Ratio of Low Slump Mortar Grouting Mixtures for Improving the Soft Ground)

  • 박언상;김병일;박승도
    • 한국지반환경공학회 논문집
    • /
    • 제21권9호
    • /
    • pp.15-24
    • /
    • 2020
  • 본 연구에서는 저유동성 몰탈 주입공법의 개량체에 관한 응력분담비를 복합지반법, 지반아칭이론, 소성각법 및 2차원과 3차원 수치해석, 3차원 모형실험을 통해 평가하였다. 복합지반법으로 계산된 응력분담비는 89.3, 3차원 지반아칭이론을 적용할 경우 3.75~59.0, 3차원 소성각법의 경우 82.8로 이론별 응력분담비의 차이가 나타났다. 2차원 수치해석 결과 응력분담비는 63.0~77.0으로 개량율이 증가할수록 증가하는 것으로 나타났고, 3차원 수치해석 결과 50.0~56.0으로 2차원 해석 결과 대비 작게 예측되었다. 대형 삼축압축셀을 이용한 특수 모형 실험의 경우 하중단계별 응력분담비는 53.0~60.0으로 나타났고, 실험으로 평가한 응력분담비는 2차원과 3차원 수치해석적 예측치 내에서 측정되었다. 본 연구에서는 저유동성 몰탈 주입 공법의 개량체에 대하여 해석 및 실험값을 바탕으로 개량율에 따른 응력분담비에 대한 예측식을 제안하였다.

P1ane Strain Strength of Fine Sands

  • Yoon, Yeo-Won;Van, Impe W.F
    • 한국지반공학회지:지반
    • /
    • 제12권3호
    • /
    • pp.5-16
    • /
    • 1996
  • 실리카질 모래에 대한 많은 시험결과로부터 삼축압축시첩과 평면변형시험간의 강도관계를 밀도와 파괴시 유효평균주응력의 함수로 표현하였다. 또한 파괴시 평균주응력과 축차응력간의 응력비가 내부마찰각의 함수로 잘 규정되었으며 그 비는 내부마찰각의 증가에 따라 감소하였다. 또한 중간주응력을 최대주응력과 최소주응력으로써 표현하였으며 이론적인 파괴면의 각도와 평면변형시험에서 관찰된 파괴면의 각도가 비교적 잘 일치함이 확인되었다.

  • PDF

단섬유 복합체에서 탄성계수비가 내부응력에 미치는 영향 (Effects of Elastic Modulus Ratio on Internal Stresses in Short Fiber Composites)

  • 김홍건;노홍길
    • 한국공작기계학회논문집
    • /
    • 제13권4호
    • /
    • pp.73-78
    • /
    • 2004
  • The conventional SLT(Shear Lag Theory) which has been proven that it can not provide sufficiently accurate strengthening predictions in elastic regime when the fiber aspect ratio is small. This paper is an extented work to improve it by modifying the load transfer mechanism called NSLT(New Shear Lag Theory), which takes into account the stress transfer across the fiber ends and the SCF(Stress Concentration Factor) that exists in the matrix regions near the fiber ends. The key point of the model development is to determine the major controlling factor among the material and geometrical coefficients. It is found that the most affecting factor is the fiber/matrix elastic modulus ratio. It is also found that the proposed model gives a good result that has the capability to correctly predict the elastic properties such as interfacial shear stresses and local stress variations in the small fiber aspect ratio regime.

반복재하후 미액상화 풍화토 지반의 변형 거동 (Post-Cyclic Deformation Behavior of Non-Liquefied Weathered Soils)

  • 최연수;정충기
    • 한국지반공학회:학술대회논문집
    • /
    • 한국지반공학회 2001년도 봄 학술발표회 논문집
    • /
    • pp.485-492
    • /
    • 2001
  • Weathered soil is one of the most representative soils in Korea. In this study, a series of cyclic triaxial tests was carried out to predict the post-cyclic deformation behavior of weathered soils in case of non-liquefaction. Excess pore pressure response during cyclic loading and volumetric strain during the dissipation of excess pore pressure were measured varying the confining pressure, relative density and cyclic stress ratio. Based on the test results, it Is found that the modified excess pore pressure ratio, excess pore pressure ratio normalized by cyclic stress ratio, is uniquely correlated with the number of cycles irrespective of confining pressure and cyclic stress ratio. Using the newly proposed MEPPR(modified excess pore pressure ratio) concept, it is possible to easily evaluate the excess pore pressure and the settlement of weathered soils due to cyclic loading by greatly reduced number of tests. It is also verified that the reconsolidation volumetric strain is independent of the way how the excess pore pressure was generated.

  • PDF

단층의 해석상의 고려사항과 암반구조물에 미치는 영향 (Consideration of FEM Analysis and Effect of Structure in Fault Rock)

  • 안성율
    • 한국지반공학회:학술대회논문집
    • /
    • 한국지반공학회 2007년 가을학술발표회
    • /
    • pp.160-169
    • /
    • 2007
  • In this study, Analyzed stress history, state of stress, ratio of stress/strength to use FEM. Fault Zone depth is 3m, 6m, 9m, 12m and 15m for study, and also Distance is 3m, 6m, 9m, 12m and 15m at center of tunnel with thickness 3m fault zone. It is not appeared that Arching in stress state and stress history by FEM. On the other hand, excessive shear stress and high compressive stress happened. Therefore, Tunnel design is desirable that do it so that state of stress that is the imbalance may be uplemented. it is important that examine each state of stress and stress history in detail tunnel design.

  • PDF

인장과 굽힘응력을 받는 판재의 표면균열해석 (Analysis of Surface Crack under Tension and Bending Stress in Plate)

  • 오환섭;박철희;허민구
    • 한국자동차공학회논문집
    • /
    • 제6권4호
    • /
    • pp.121-128
    • /
    • 1998
  • In this study, when tension and bending stress act on plate simultaneously, stress intensity factor is analyzed at crack tip with using BEM(Boundary Element Method). In this analysis, stress intensity factors(S.I.F) are defined for variable ligament, aspect and stress ratio($\sigma$T/$\sigma$B). Consequently, predicted that crack grow to depth direction at low aspect and ligament ratio in tension stress and to surface direction in bending stress. Tension and bending stress act on plate same time, effect of tension stress in the first stage and effect of bending stress in the after stage was to observed. The outbreak of secondary crack in backside is under the control of stress amplitude and predict that the point of outbreak is mear backside.

  • PDF

순수 티타늄 판재의 피로균열 전파거동에 관한 연구 (A Study on Fatigue Crack Propagation Behavior with Pure-Ti Plate)

  • 오세욱;김태형;김득진;임만배
    • 한국해양공학회지
    • /
    • 제9권1호
    • /
    • pp.92-100
    • /
    • 1995
  • The effect of different anisotropy and stress ratio on fatigue crack propagation behavior was investigated under various stress ratio(R=-0.4, -0.2, 0.2, 0.2, 0.4) using pure titanium sheet used in aerospace, chemical and food industry. The rack closure behavior under constant load amplitude fatigue crack propagation test was examined. Fatigue crack propagation rate da/dN was estimated in terms of effective stress intensity factor range, $\Delta$K$_{eff}$, regardless of various stress ratio but was influenced by anisotropy. Also, it was found that the effect of anisotropy was considerably decreased but still not negligible when he da/dN was evaluated by a conventional parameter, $\Delta$$K_{eff}$/E and when the modified da/dN.$\sqrt{\varepsilon}_f$ was evaluated by $\Delta$$K_{eff}$/E. On the other hand, da/dN could be evaluated uniquely by effective new parameter, $\Delta$K$_{eff}$/$sigma_{ys}$, regardless of anisotropy, as int he following equation da/dN=C''[\frac{{\Delta}K_{eff}}{{\sigma}_{ys}}]^{n''}. And effective stress intensity factor range ratio, U was estimated by the following equation with respect to the ratio of reversed plastic zone size, $\Delta r_{p}$ to monotonic plastic zone size, $r_p$ regardless of stress ratio and anisotropy. U=-4.45$(\Delta r_{p}/r_{p})^{2}$+4.1$(\Delta r_{p}/r_{p})$+0.245_{p})$+0.245

  • PDF

고강도 알미늄 합금재에 있어서 크랙열림점 평가에 관한 연구(I) (A Study on Evaluation of Crack Opening Point in High Strength Aluminum Alloy(I))

  • 최병기
    • 오토저널
    • /
    • 제15권1호
    • /
    • pp.100-106
    • /
    • 1993
  • This paper aims to synthesize the research on fatigue fracture mechanisms of high strength aluminum alloys which are widely used in motorcars or airplanes to prevent accidents. To measure the data of crack opening ratio, the same materials and method are used for evaluating the fatigue crack propagation rate as an effective stress intensity factor. But, many researchers have brought different results. An exact crack opening ratio was, therefore, proposed for getting a more accurate fatigue crack propagation rate. The main conclusions obtained are as follows. (1) As a result of the fatigue test, the value of the crack opening ratio is the same regardless of the stress ratio. (2) The value of crack opening ratio is different according to the measuring point. After measuring the crack propagation rate by using an effective stress intensity factor, the crack opening ratio value measured at the crack mouth by a clip gage, or measured rear of the specimen by a strain gage is more accurate than that by any other measuring test.

  • PDF

고강도 철근 콘크리트 보의 휨 설계 및 연성능력 (Flexural Design and Ductile Capacity of Reinforced High Strength Concrete Beams)

  • 신성우;유석형;안종문;이광수
    • 콘크리트학회지
    • /
    • 제8권6호
    • /
    • pp.141-149
    • /
    • 1996
  • 동일한 인장철근배근상태($\rho$/$\rho_b$=constant)에서 휨을 받는 고강도 철근 콘크리트 보는 보통강도의 철근 콘크리트보에 비해 더욱 취성적인 거동을 하게 된다. 본 실험결과 연성적인 파괴를 유도하기 위하여 콘크리트의 강도가 830kg/$cm^2$이상일 경우 철근비를 $0.6\rho_b$이하로 배근하여야 할 것으로 나타났다. 또한 콘크리트 강도가 830kg/$cm^2$ 이상일 경우 사각형응력 블록을 사용한 ACI 휨강도식의 안전율이 감소하였으며, 삼각형에 가까운 압축응력 분포를 나타내었다. 이는 콘크리트 강도가 증가할수록 응력-변형률 곡선이 거의 선형적으로 증가하는 재료적 성질에 기인하는 것으로 사료된다.