• 한국생산제조학회지
• /
• 제6권3호
• /
• pp.111-117
• /
• 1997

The sudden-stop apparatus is made to measure the residual stress of the infinitesimal area at the turning work surface by using the X-ray stress apparatus. This study is trued to make the cutting work the instantaneous stopping state in the normal working state. The behaviour of work material near the tool is estimated. The estimation method is that the distribution of residual stress can be also measured. The object is to clarify and control the mechanism to leave the adequate stress of the finishing surface. It's beginning is due to observe the occurrence state of the residual stress at the cutting work. The result obtained by this study is as follows. The chips are not separated from the work materials at all the cutting experiments of built-up edges or the shearing areas etc. which can be precisely observed by using the sudden-stop apparatus. The strain of movable system which can be seen at the part of working layer means the size of strain. This experiment proves that the working strain should be lessened to make the size of strain control the residual stress happened at the cutting surface.

• 한국가스학회지
• /
• 제17권5호
• /
• pp.51-57
• /
• 2013

최근 들어 다양한 재료 및 제조기술의 개발로 가스관 품질이 향상되어 매설심도를 저심도화 할 수 있는 환경이 조성되고 있다. 또한 선진 외국과 비교하여 국내 매설깊이 기준이 약 50cm 정도 깊은 것으로 조사되어 시공비용, 차량지체비용 등을 고려하였을 때 비효율적인 매설깊이 규정인 것으로 판단된다. 따라서 본 연구에서는 매설깊이 변화(0.8m, 1.0m, 1.2m)에 따른 가스관의 응력 및 변형 거동을 분석하였다. 본 연구에서는 수치해석 및 현장시험을 통하여 매설심도 변화에 따른 가스관(API 5L)의 거동특성을 분석하였다. 분석결과, 매설심도의 감소가 가스관의 응력, 변형 특성에 큰 영향을 미치지 않을 것으로 판단되었다.

• 한국전산구조공학회논문집
• /
• 제15권1호
• /
• pp.69-84
• /
• 2002

본 논문에서는 축방향 인장 부재의 균열거동과 철근콘크리트 부재의 인장강화현상을 고려하기 위한 새로운 해석적 기법을 제시하였다 균열 후 거동 규명을 위하여 부착응력-슬립의 관계나 부탁 응력의 분포를 가정하는 기존의 해석방법과는 달리, 철근과 콘크리트의 변형률 분포 함수를 다항식으로 가정하여, 이를 바탕으로 일축 인장부재의 균열 해석 기법을 구성하였다. 제시한 균열 해석모델은 기존의 해석기법과 비교하여, 철근콘크리트 구조물의 유한요소해석을 위한 균열 후의 평균 응력-변형률 관계를 정의하거나, 부재의 길이방향으로 철근과 콘크리트가 분담하는 하중 및 슬립량 산정시 매우 효율적이다. 제안된 모델을 이용하여 얻어진 균열하중과 보강철근의 신장률 값을 다른 해석기법 및 실험값과 비교한 결과 만족할만한 정확도를 보여주었다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 가을 학술발표회 논문집
• /
• pp.653-658
• /
• 1997

Recently, carbon Fiber sheet (CFS) is frequently used for strengthening deteriorated concrete structures. To strengthening damaged structures, the property and characteristic of the bond between CFS and the concrete surface must be understood. The tensile test of single lap shear specimen was performed to study bond strength, bond stress distribution and stress transfer between CFS and concrete surface according to the bond length. Based on the test results, there were ultimate influence length (UIL) in which bond stress was distributed, and ultimate strain reduction ratio (USRR) by which strain was reduced linearly. Bond resisting force (BRF) was estimated by UIL and USRR, and which was compared with ultimate loads. According to the results of comparison, it was shown that ultimate bond strength could be estimated reasonablely by BRF.

• 대한기계학회논문집
• /
• 제12권6호
• /
• pp.1207-1216
• /
• 1988

본 연구에서는 이 염색격자법을 이용하여 가장 기본적인 복합재인 탄성계수가 서로 다른 두 물체로 구성된 2상적합재를 제작할 수 있는가를 검토하였고, 또한 제작 완성된 접합재를 이용하여 접합경계면 부근의 국소영역에서의 3차원적인 변형거동을 관찰한 것이다.

• 한국자동차공학회논문집
• /
• 제11권4호
• /
• pp.125-134
• /
• 2003

In this study, Mooney-Rivlin 1st model and Mooney-Rivlin 3rd model are adopted as strain energy density functions of the rubber compounds of a radial tire. It is shown that the FE analysis using Mooney-Rivlin models for rubber compounds may provide good approximations by employing the appropriate strain range of experimental stress-strain data in a way to describe the stress-strain relationship accurately. Especially, Mooney-Rivlin 3rd model gives an accurate stress-strain relationship regardless of the fitting strain range used within the strain of 100%. The static nonlinear FE analysis of a tire inflation is performed by employing an axisymmetric model, which shows that the outside shapes of the tire before and after inflating the tire agree well with those of the real tire. Additionally, the deformations at crown center and turning point on sidewall, distribution of belt cord force, interlaminar shear strain are predicted in terms of variation of belt cord angle which is known as the most influential factor in inflation behavior of a tire.

• Tribology and Lubricants
• /
• 제24권2호
• /
• pp.90-95
• /
• 2008

An elastic-plastic contact analysis is developed using a semi-analytical method. The elastic contact is solved within a Hertz theorem. The reciprocal theorem with initial strains is then introduced, to express the surface geometry as a function of contact stress and plastic strains. The irreversible nature of plasticity leads to an incremental formulation of the elastic-plastic contact problem, and an algorithm to solve this problem is set up. Closed form expression, which give residual stresses and surface displacements from plastic strains, are obtained by integration of the reciprocal theorem. The distribution of contact stress, residual stress and plastic strain are obtained by the changed surface geometry.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2003년도 가을 학술발표회 논문집
• /
• pp.179-186
• /
• 2003

This paper describes an extension of a numerical model, which was developed to simulate the nonlinear behavior of reinforced concrete (RC) structures subject to monotonic in-plane shear. While maintaining all the basic assumptions adopted in defining the constitutive relations of concrete under monotonic loadings, a hysteretic stress-strain relation of concrete, which crosses the tension-compression region, is defined. In addition, curved unloading and reloading branches inferred from the stress-strain relation of steel considering the Bauschinger effect are used. Modifications of the stress-strain relation of concrete and steel are also introduced to reflect a pinching effect depending on the shear span ratio and to represent an average stress distribution in a cracked RC element, respectively.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.2
• /
• pp.489-494
• /
• 2006

The strain distribution in the vicinity of a hole in a tensile strip was measured using an image correlation method. The objective of this study is to evaluate the capability of predicting the strain component response using a constitutive model that was developed for use with paper materials. The need for a special constitutive model for paper derives from the characteristics of pronounced anisotropy and the fact that the material behaves differently under compressive loading than it does under tensile loading. The results of the simulation showed that predictions of strain distribution around the hole were in agreement with the experimental result trends, however, the agreement deteriorated as the edge of the hole was reached. It was observed that there is extensive inelastic strain that takes place around the hole prior to failure of the tensile strip. The simulation results showed that any difference between tensile and compressive behavior that may exist for paper material does not have any significant effect for the problem of this study because the level of compressive stress is quite low in comparison with compressive failure values.

• 한국생산제조학회지
• /
• 제7권3호
• /
• pp.68-78
• /
• 1998

Welding structure contains residual stress due to thermal-plastic strain during welding process, and its magnitude and distribution depend on welding conditions. Cracks initiate from various defects of the weldment, propagate and lead to final fracture, The crack initiation and propagation processes are affected by the magnitude and distribution. Therefore, the magnitude and distribution of weldment residual stress should be considered for safety design and service of welding structures. Also it is very important that more accurate assessment method of fatigue crack growth must take into account the redistributing the residual stress quantitively. because the residual stress in weldment has characteristics of its redistribution with loading magnitude, number of cycles and fatigue crack propagation. In this study fatigue crack behavior of STS-304 weldment was investigated during crack propagation into tensile residual stress region or compressive residual stress region. Crack growth rates were predicted and compared with experimental results.