• Journal of Korean Society on Water Environment
• /
• v.33 no.2
• /
• pp.187-196
• /
• 2017

To ensure hygienic safety of drinking water in a water storage tank, the concentrations of residual chlorine should be above a certain regulation level. In this study, we conducted model simulations to investigate the effects of temperature on residual chlorine in water storage tank conditions typically used in Seoul. For this, values of model parameters (decomposition rate constant, sorption coefficient, and evaporation mass transfer coefficient) were experimentally determined from laboratory experiments. The model simulations under continuous flow conditions showed that the residual chlorine concentrations were satisfied the water quality standard level (0.1 mg/L) at all the temperature conditions ($5^{\circ}C$, $10^{\circ}C$, $15^{\circ}C$, $20^{\circ}C$ and $25^{\circ}C$). Meanwhile, when the tanks had a no flow condition (i.e., no tap-water influent due to a sudden shut-down), the concentrations became lower than the regulatory level after certain periods. The findings from this modeling works simulating Seoul's water storage tanks suggested disappearance rate of residual chlorine could be reduced through the tanks design optimization with maintenance of low water temperature, minimization of air flow and volume, suppression of dispersion and the use of wall materials with low sorption ability.

• Asian-Australasian Journal of Animal Sciences
• /
• v.14 no.9
• /
• pp.1316-1320
• /
• 2001

The objectives of this study were to investigate the quality characteristics of restructured pressed smoked duck steak from the breast meat of Cherry Valley ducks. Different levels of isolated soybean protein (ISP) (0, 15 and $30g{\cdot}kg^{-1}$) or carrageenan (5, 10 and $15g{\cdot}kg^{-1}$) were added to manufacture the restructured pressed smoked duck steak. The results were as follows: No significant differences were observed for moisture, crude fat, crude protein, cooking loss and water holding capacity of products from all treatments. The panel test scores showed that color, flavor and binding ability of products were considered acceptable. The drip loss in control sliced-products was significantly higher than products containing ISP or carrageenan (p<0.05) during storage at $-18^{\circ}C$ for 12 weeks. The pH value, volatile basic nitrogen (VBN) value and thiobarbituric acid (TBA) value of vacuum-packaged products did not change significantly during storage at $-18^{\circ}C$ for 6 weeks. However, TBA values increased with storage time. The viable bacterial counts were about $10^{3}-10^{4}CFU/g$ during storage at $-18^{\circ}C$ for 12 weeks. The products remained good quality during the storage period.

• Journal of Power Electronics
• /
• v.8 no.4
• /
• pp.291-300
• /
• 2008

In this paper power system and drive-train for omni-directional autonomous mobile robots with multiple energy storage units are presented. Because in proposed system, which is implemented in soccer robots, the ability of power flow control from of multiple separated energy storage units and speed control for each motor are combined, these robots can be derived by more than one power source. This capability, allow robot to diversify its energy source by employing hybrid power sources. In this research Lithium ion polymer batteries have been used for main and auxiliary energy storage units because of their high power and energy densities. And to protect them against deep discharge, over current and short circuit, a protection circuit was designed. The other parts of our robot power system are DC-DC converters and kicker circuit. The simulation and experimental results show proposed scheme and extracted equations are valid and energy management and speed control can be achieved properly using this method. The filed experiments show robot mobility functions to perform the requested motion is enough and it has a high maneuverability in the field.

• Journal of Powder Materials
• /
• v.24 no.5
• /
• pp.395-399
• /
• 2017

Solder paste is widely used as a conductive adhesive in the electronics industry. In this paper, nano and microsized mixed lead-free solder powder (Sn-Ag-Cu) is used to manufacture solder paste. The purpose of this paper is to improve the storage stability using different types of solvents that are used in fabricating the solder paste. If a solvent of sole acetate is used, the nano sized solder powder and organic acid react and form a Sn-Ag-Cu malonate. These formed malonates create fatty acid soaps. The fatty acid soaps absorb the solvents and while the viscosity of the solder paste rises, the storage stability and reliability decrease. When ethylene glycol, a dihydric alcohol, is used the fatty acid soaps and ethylene glycol react, preventing the further creation of the fatty acid soaps. The prevention of gelation results in an improvement in the solder paste storage ability.

• Korean Journal of Poultry Science
• /
• v.28 no.3
• /
• pp.225-229
• /
• 2001

This experiment was carried out to investigate the effects of storage temperature and time on hatch-ability of the commercial Ross broiler breeder eggs. In Trial 1,720 eggs collected in the morning were allotted to four storage time treatments (3, 5, 7 and 9 days), with three replicates per treatment. The storage temperature was fixed at $4^{\circ}C$. In Trials 2 and 3, similar protocol was used as in Trial 1 except that the storage temperature was fixed at $17^{\circ}C$ and $28^{\circ}C$respectively. In Trial 1, hatchability was significantly (P<0.05) reduced when the eggs were stored more than 3 days. In Trial 2, no significant difference was found among all treatments, indicating that, at 17$^{\circ}C$ storage temperature, the eggs could be stored up to 9 days without reducing hatchability. In Trial 3, however, hatchability of eggs stored for 9 days was significantly reduced compared to the other treatments. In conclusion, we found out that optimum hatchability can be achieved with a storage temperature of $17^{\circ}C$ for Ross broiler eggs stored for up to 9 days.

• Journal of Power Electronics
• /
• v.13 no.2
• /
• pp.313-321
• /
• 2013

This paper describes the operation analysis results of a communication-based DC micro-grid using a hardware simulator developed in the lab. The developed hardware simulator is composed of distributed generation devices such as wind power, photovoltaic power and fuel cells, and energy storage devices such as super-capacitors and batteries. Whole system monitoring and control was implemented using a personal computer. The power management scheme was implemented in a main controller based on a TMS320F28335 chip. The main controller is connected with the local controller in each of the distributed generator and energy storage devices through the communication link based on a CAN or an IEC61850. The operation analysis results using the developed hardware simulator confirm the ability of the DC micro-grid to supply the electric power to end users.

• Nuclear Engineering and Technology
• /
• v.43 no.1
• /
• pp.75-82
• /
• 2011

The neutron multiplication factor in spent fuel storage racks, in which a stainless steel plate encloses a fuel assembly, was evaluated according to the variation of distance between the fuel assembly and stainless steel plate, as well as the pitch. The stainless steel plate position with the lowest multiplication factor on each pitch consistently appeared as 6mm or 9mm away from the outmost surface of the fuel assembly. Because the stainless steel plate has a thermal neutron absorption cross section, its ability to absorb neutrons can work best only if it is installed at the position where thermal neutrons can be gathered most easily. Therefore, the stainless steel plate position should not be too close or too far away from the fuel assembly, but it should be kept a pertinent distance from the fuel assembly.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.573-576
• /
• 2001

In the research fields of energy storage, and more specifically of supplying high powers, electrochemical supercapacitor have been among the most studied systems for many years. One of the possible applications is in electric vehicles. We have been working on electronically conducting polymers for use as active materials for electrodes in supercapacitors. These polymers have the ability of doping and undoping with rather fast kinetics and have an excellent capacity for energy storage. polythiophene (Pth) and polyparafluorophenylthiophene (PFPT) have been chemically synthesized for use as active materials in supercapacitor electrodes. Electrochemical characterization has been performed by cyclic voltammetry and an electrode study has been achieved to get the maximun capacity out of the polymers and give good cyclability. specific capacity values of 7mAh/g and 40mAh/g were obtained for PFPT and polythiophene, respectively. Supercapacitors have been built to characterize this type of system. Energy storage levels of 260F/g were obtained with Pth and 110F/g with PFPT

• Nuclear Engineering and Technology
• /
• v.43 no.6
• /
• pp.489-498
• /
• 2011

UK National Nuclear Laboratory's (NNL's) version of the ENIGMA fuel performance code is described, including details of the development history, the system modelled, the key assumptions, the thermo-mechanical solution scheme, and the various incorporated models. The recent development of ENIGMA in the areas of whole core analysis and dry storage applications is then discussed. With respect to the former, the NEXUS code has been developed by NNL to automate whole core fuel performance modelling for an LWR core, using ENIGMA as the underlying fuel performance engine. NEXUS runs on NNL's GEMSTONE high performance computing cluster and utilises 3-D core power distribution data obtained from the output of Studsvik Scandpower's SIMULATE code. With respect to the latter, ENIGMA has been developed such that it can model the thermo-mechanical behaviour of a given LWR fuel rod during irradiation, pond cooling, drying, and dry storage - this involved: (a) incorporating an out-of-pile clad creep model for irradiated Zircaloy-4; (b) including the ability to simulate annealing out of the clad irradiation damage; (c) writing of additional post-irradiation output; (d) several other minor modifications to allow modelling of post-irradiation conditions.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.122-125
• /
• 2006

This paper deals with the Ondol, Korean under-floor heating system using latent heat storage materials. It has been recognized that the heating system using the latent heat storage materials are economically efficient and comfortable. For the comparison and analysis to the data of the existing experiment, a repetitive experiment makes sure the ability of Ondol panel.