• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.2
• /
• pp.94-102
• /
• 2020

Precast concrete segment arch system has an economic and construct ability that combined with advantage of precast concrete and arch behavior. A precast concrete segment arch system with outrigger is consisted of segmented precast panels, a steel outrigger rib, and V-strip to connect precast panels with a steel outrigger rib and cast-in-place anchors in precast panels to connect V-strip should have sufficient pull-out capacity to form its arch shape by site lifting for assembled precast panels and outriggers. However, it is difficult to secure its embedment depth due to the relatively shallow thickness of precast panel. It can be also occurred that flexure deformation of precast panels caused by its pull-out behaviors. In this study, pull-out capacity of cast-in-place anchor was examined for construction of precast concrete segment arch system with outriggers. Therefore, a total of 24 precast panel specimens were fabricated to examine pull-out capacities of cast-in-place anchor in precast panels, and installation depth of anchors, diameter of anchors and wire mesh effects for the precast panel were examined. From this pull-out tests, its pull-out capacities and failure modes were evaluated and the type of the cast-in-place anchor applicable to the precast concrete segment panel arch system with outriggers was determined from comparison of the design specification values.

• Journal of Korean Dental Science
• /
• v.3 no.1
• /
• pp.5-10
• /
• 2010

This study sought to compare the amounts of posterior anchorage loss during the en masse retraction of the upper anterior teeth between orthodontic mini-implant (OMI) and conventional anchorage reinforcement (CAR) such as headgear and/or transpalatal arch. The subjects were 52 adult female patients treated with sliding mechanics (MBT brackets, .022" slot, .019X.025" stainless steel wire, 3M-Unitek, Monrovia, CA, USA). They were allocated into Group 1 (N=24, Class I malocclusion (CI), upper and lower first premolar (UP1LP1) extraction, and CAR), Group 2 (N=15, Cl, UP1LP1 extraction and OMI), and Group 3 (N=13, Class II division 1 malocclusion, upper first and lower second premolar extraction, and OMI). Lateral cephalograms were taken before (T0) and after treatment (T1). A total of 11 anchorage variables were measured. Analysis of variance was used for statistical analysis. There was no significant difference in treatment duration and anchorage variables at T0 among the three groups. Groups 2 and 3 showed significantly larger retraction of the upper incisor edge (U1E-sag, 9.3mm:7.3mm, P<.05) and less posterior anchorage loss (U6M-sag, 0.7~0.9mm:2mm, P<.05; U6A-sag, 0.5mm:2mm, P<.01) than Group 1. The ratio of retraction amount of the upper incisor edge per 1 of anchorage loss in the upper molar made for the significant difference between Groups 1 and 2 (4.6mm:7.0mm, P<.05). Group 3 showed a relatively distal inclination of the upper molar (P<.05) and the intrusion of the upper incisor and first molar (U1E-ver, P<.05; U6F-ver, P<.05) compared to Groups 1 and 2. Although OMI could not shorten the treatment duration, it could provide better maximum posterior anchorage than CAR.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.9
• /
• pp.1260-1266
• /
• 2002

In this study, to make an excellent heat pipe, the manufacturing technology of a sintered wick was investigated. Making a sintered wick is known to be very difficult but it has many advantages. For example, the porosity and pore size can be controlled and the capillary force is great. The mixture of copper and pore former powder was used as a wick material and ceramic-coated stainless steel was used as a mandrel which is necessary for vapor flow. To analyze the feature of the manufactured wick, not only porosity and pore size were measured but also the sintered structure was observed. A heat pipe with sintered wick was manufactured and the performance test of the heat pipe was performed in order to review cooling performance. The performance test results for the 4mm diameter heat pipe with the sintered wick shows the stability since the temperature difference between a evaporator and a condenser of the heat pipe is less than 4.4$^{\circ}C$, and thermal resistance is less than 0.7$^{\circ}C$/W, In the meantime the composite wick that is composed with sintered and woven wire was also examined. The heat transfer limit of the heat pipe with composite wick was enhanced about 51%~60% compare to the one with sintered wick.

• The korean journal of orthodontics
• /
• v.34 no.3 s.104
• /
• pp.269-277
• /
• 2004

A modified removable appliance for molar distalization called C-activator was used in a 10-year old male patient with a Class II anterior deep bite malocclusion with upper arch discrepancy. The treatment plan involved correcting the Class ll relationship, distalizing both upper first molars, and regaining space for the erupting canines. The C-activator, which was used for 6 months, consisted of a labial framework formed from .036-in stainless steel wire and an acrylic monobloc. Both the closed helices of the labial framework were compressed for reactivation during the C-activator treatment period. C-activator mechanics simultaneously achieved distalization of the upper first molars into their proper positions and repositioning of the mandible. After 21 months of treatment, the correct oberbite and overjet was obtained and contributed to an Improvement in facial balance. The treatment results were stable 6 months after debonding. Fabrication and placement of the new appliance and clinical procedures are detailed, and the treatment sequence and results of this case are presented as follows.

• The korean journal of orthodontics
• /
• v.46 no.2
• /
• pp.73-80
• /
• 2016

Objective: The purpose of this study was to investigate the static (SFF) and kinetic frictional forces (KFF) in sliding mechanics of hybrid bracket systems that involve placing a conventional bracket (CB) or active self-ligating bracket (ASLB) on the maxillary anterior teeth (MXAT) and a passive SLB (PSLB) on the maxillary posterior teeth (MXPT). Methods: The samples consisted of two thoroughbred types (group 1, anterior-CB + posterior-CB; group 2, anterior-ASLB + posterior-ASLB) and four hybrid types (group 3, anterior-CB + posterior-PSLB-type 1; group 4, anterior-CB + posterior-PSLB-type 2; group 5, anterior-ASLB + posterior-PSLB-type 1; group 6, anterior-ASLB + posterior-PSLB-type 2) (n = 13 per group). After maxillary dentition alignment and maxillary first premolars removal in the stereolithographically-made typodont system, a $0.019{\times}0.025$-inch stainless steel wire was drawn through the right quadrant of the maxillary arch at 0.5 mm/min for 5 min. The SFF and KFF were measured with a mechanical testing machine and statistical analyses were performed. Results: Four different categories of SFF and KFF were observed among all groups (all p < 0.001). Group 1 demonstrated the highest SFF and KFF; groups 4 and 3 were second and third highest, respectively. The fourth category included groups 2, 5, and 6. Placing PSLBs on the MXPT resulted in significant SFF and KFF reductions in cases with CBs on the MXAT, but not in cases with ASLBs on the MXAT. Conclusions: These data might aid in the development of a hybrid bracket system that enables low-friction sliding of an archwire through the MXPT.

• Journal of the Korean Society of Industry Convergence
• /
• v.6 no.1
• /
• pp.81-86
• /
• 2003

For the simultaneous removal of $SO_2$/NOx from an iron-ore sintering plant, industrial plasma experiments have been conducted with a flue gas flow rate of $5,000Nm^3/hr$. The maximum 40kW power using the magnetic pulse compression (MPC) system generates a peak value of 100-150kV pulse voltage with its risetime of 200nsec and full width at half maximum (FWHM) of 500nsec, and with a frequency <300Hz. The plasma reactor module adopts a wire-plate structure with a gap of 200-400mm ID between plates. Initial concentrations of $SO_2$ and NOx were around 100-150ppm, respectively in the presence of 15% $O_2$ and <10% $H_2O$. Various reaction parameters such as specific energy ($Whr/Nm^3$), $NH_3$ injection with corona discharge, flow rate and injection of hydrocarbons were investigated for $SO_2$/NOx removal characteristics. About 90/65% of $SO_2$/NOx were simultaneously removed with a specific energy of $3.0Whr/Nm^3$ when both $NH_3$ and hydrocarbons were injected. Practical implications that the pilot-scale plasma results provide are further discussed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.10
• /
• pp.788-792
• /
• 2010

The yttrium-barium-copper-oxide (YBCO) coated conductor, which supplement the fault of the existing superconducting current-limit materials YBCO thin film, bismuth-strontium-calcium-copper-oxide(BSCCO) wire and bulk, has been improved its mechanical weakness and has high index; hence, after quench YBCO coated conductor could limit the fault current effectively because of fast resistance occurrence speed. Furthermore, it has wide applicable area as an current limit material because it shows different resistance occurrence tendency by the thickness and kind of stabilization material sputtered on the superconducting layer. Therefore, many researchers are carrying out the study of application of YBCO coated conductor to superconducting fault current limiter (SFCL) for making high quality current limit element, based on resistance type. On the other hand, the study for other type except resistance type has been rarely conducted for the application of YBCO coated conductor to SFCL as an current limit element. Consequently, in this study, YBCO coated conductor with different stabilization layer Cu and Stainless steel, is applied to SFCL using iron core and coil, and examine the many index points as an current limit element, such as current limit characteristic, the tendency of resistance occurrence, response time, the temperature trend for stability.

• The Journal of Engineering Geology
• /
• v.30 no.3
• /
• pp.279-288
• /
• 2020

Sand dams are formed by installing beams across rivers and filling the secured space with water and a permeable material, such as sand, which stores the water in available pore space. These structures have mainly been reported in Kenya, Africa. This study proposes a sand dam design that improves structural safety and water intake. First, to increase the stability of the concrete wall of the dam, steel barbed wire connections are proposed for construction. Second, by using geotextile fabrics, evaporation may be reduced from 45% to 8%, and horizontal permeable discharge could be reduced markedly, therefore improving water storage capabilities. In addition, the water intake increased by ~2.4 times that of the previous design. Third, filtration efficiency is improved by selecting a sedimentary site for improved water quality. Finally, the installation of a tensiometer is suggested for monitoring the sand dam.

• Journal of the Korea Furniture Society
• /
• v.19 no.6
• /
• pp.439-446
• /
• 2008

High Tech Design manner is a design concept that had been constantly discussed in constitution process of the West art history and modem ideology and had been experimented in industry, having started from futurism and structuralism in the early 20th century through Kinetic Art & Technology Art and up to now. High Tech Design had a great influence also on Post Modernism and more important is that this manner of design will be existing continually in the future too. From the modem times when machine civilization started, the artist and designers expressed a utopia will showing the future world with help of High Tech Design and modem people are realizing technology images as a utopia, in the space and material presented by this high tech design. And this utopia imply the images of dynamic power, speed making a voyage in universe, dream of future, hope, mass production, earth's environment, wealth etc. High Tech furniture was lightly designed by using thin steel wire, structure stressing the metallic characteristic and tempered glass, and it was used for presenting a convenient interior space visually, and with that it can make a unified sense in High Tech interior space, and a contrary effect compared with minimal space. High Tech Design equipped with glass and metal materials looking inappropriate for our interior space due to their sharp and cold image has been regularly used as living furniture, not only decoration function, and then there must be reasons for that. This study intends to research how High Tech Design has been changed and developed in the design history & West art history from the early 20th century, and to present it's value of development as data orienting, namely a direction for the industry of the next-generation and furniture design.

• Korean Institute of Interior Design Journal
• /
• no.13
• /
• pp.187-196
• /
• 1997

A Study on the Characteristics of the Modern Chair Design The features of the modern chair design results from the diverse life style unfolded as per the 20th century social structure and the change of the residential space, and new design has been being developed by the scientists and the artists in various fields through their cooperated work in a way. The field of the scientific or technical study and creation of arts can be developed where they can evoke the sympathy in the circumstances under which the various styles of both arts and science meet across, complement crash together, and grow up. The operation which can control in the network of such pluralistic sphere has been needed for a long period and it has been facing the needs from a time and society. The engineering furniture as the counterplan of the above has brought the value of materials into relief to the forms of human life by making the properties of matter the maximum value or changing it. It can be summarized as following characteristics in its materials and forms along as well as the 3 types (handycrafty, mechanical, and ecological expression) in process through the 20th century. 1. Characteristics in Materials elasticity of the chair as per the changes of the flexibility in the steel pipe development of systematic chair using the plasticity of the plywood, plastic, and wire lightweight due to the materials such as aluminum. 2. Formative characteristics formative simplicity for the increase of the function and the quality improvement such as sociality, productivity, environmental and aesthetic nature emphasis on the structure as per the architectural environment and tecniques pursuit of the forms as a container of the human body seeking for the formative values as the cultural symbols coping with the needs from thepluralistic social structure Furniture is not the makeup for convenience sake but most importantexpression as necessaries of our environments. It should identify itself always as per these kind of needs and also it should be able to used to keep the relation of such mutual division, otherwise the purchase of new furniture should be necessary according to every change of the existing situatiov. Our residence doesn't need the specific style but expresses only the properties of the dwellers.