• The Journal of the Petrological Society of Korea
• /
• v.18 no.4
• /
• pp.315-336
• /
• 2009

We have studied the orientational characteristics of microcrack frequency, it's length and density in Tertiary crystalline tuff from the northeastern part of the Gyeongsang Basin. 134 sets of microcracks on horizontal surfaces of 3 rock samples from Heunghae-eup were distinguished by enlarged photomicrographs of the thin sections. The variability in patterns among microcrack length-frequency histograms for three rock samples from different altitudes were derived. The pattern of histograms changes progressively from negative exponential form to log-normal form in proportion to altitude. The distribution pattern for rock sample no.1 from lower altitude shows the broad length distribution characterized by higher mean and median, and higher standard deviation. Meanwhile, this distribution pattern corresponds with characteristics of joint length distribution in sedimentary rocks of the lower part of the Gyeongsang Supergroup. The occurrence frequency of shorter microcracks increases toward both NW and NE directions from the $N0{\sim}10^{\circ}W$, with the dominant direction of $N80{\sim}90^{\circ}W$ and $N80{\sim}90^{\circ}E$, respectively. This distribution pattern represents the relative differences in formation timing among microcrack sets and the result of the new initiation of shorter microcracks. Meanwhile, the longest microcracks within $N60{\sim}70^{\circ}W$($L_{max}$:1.18 mm) and $N0{\sim}10^{\circ}W$($L_{max}$:0.80 mm) directions are seen, but this kind of microcracks are very limited in number. Whole domain of the directional angle($\theta$)-frequency(N), length(L) and density($\rho$) chart can be divided into five sections in terms of phases of the distribution of related curves. From the distribution chart, density curve shows five distinct peaks in the WNW-ESE($N70{\sim}80^{\circ}W$), NS~NNE-SSW($N0{\sim}10^{\circ}W$, $N10{\sim}20^{\circ}E$), ENE-WSW($N50{\sim}60^{\circ}E$), and nearly EW($N80{\sim}90^{\circ}E$) directions, respectively. Especially, main directions of faults correspond with the directional angle showing high density. Consequently, these distribution patterns of density curve reflect the representative maximum principal stress orientations suggested in previous studies.

• Journal of dental hygiene science
• /
• v.11 no.1
• /
• pp.15-21
• /
• 2011

Introduction The aim of this study, personal trait and their dental care based on experience level of dental fear is to analyze the differences. Catastrophizing is an irrational belief that something is far worse than it actually is. Because it makes it possible to analyze patients' anxious thoughts and tendencies. Methods The Dental Fear Survey(DFS) and Anxious Thoughts and Tendencies(AT&T) were used as measuring tools, and the independent sample t-test and ANOVA were performed on the basis of the mean value of the summated scale scores and the standard deviation. On the factors to dental anxiety, the multiple regression analysis was performed. Results Demographically, the total DFS score was higher in women($25.73{\pm}8.27$) than in men. Also, AT&T was higher in women($31.01{\pm}7.05$) (p<0.05). Dental fear was intense in the group of patients who visited dental clinics only problems($25.29{\pm}8.57$) than in those regular visited($22.29{\pm}7.78$). In relation to dental experiences, the DFS score was significantly higher in children. In many cases, patients experienced therapeutic pains in children($26.40{\pm}9.54$) (p=0.004). Also in many patients, dental anxiety began to occur in adolescence(44.3%). The multiple regression analysis result, it was found that dental treatment pain and their AT&T wielded great influence upon dental fear.

• The Journal of Small Business Innovation
• /
• v.20 no.3
• /
• pp.1-17
• /
• 2017

There is a serious information asymmetry between internal managers and outside investors in the process during IPOs. One mechanism that mitigates this information asymmetry is a high quality auditor. Since prior research document auditors' effect on newly listed firms at the IPO year, what has not yet been revealed in previous studies is the behavior of firms and auditors after listing. In this study, we investigate (i) the firms tendency of contracting with Big N auditors, and (ii) the effect of Big N auditors on accounting quality after the years of IPOs. Using a sample of 7,678 (1,892 firm-years of after IPOs, and 5,786 control firm-years) KOSDAQ observations between 2002 and 2012, we find that the likelihood of contracting with Big N auditor lasts only for two years after IPO compare to that of non-IPO control years. Secondly, we find that the effect of Big N auditors on clients' earnings management lasts for a very short period after IPO. These findings suggest that although prior literature argue that Big N auditors reduce earnings management of their clients, at least the period right after IPO, it is not consistent. Our study contributes to the existing literature in several ways. First, we provide new evidences of firms' auditor selection decisions by investigating years after the listing. In second, as an evidence of accruals reversal, we document decrease in discretionary accruals after IPOs. Third, we find that there is not always a positive relation between Big N auditor and accounting quality by showing the insignificant Big N auditor effect after IPOs. Our results also suggest several implications to IPO related stakeholders. First, to IPO firms, we provide evidences that decisions of hiring auditors affect firms earnings. Also, lead IPO underwriters may consider how these decisions influence future performance. Second, investors may want to use information not only in the preofferings but also after public offerings. Our study insists that auditor hiring decisions affects their own welfare. Finally, accounting standard setters may find these results useful for evaluating how much discretion they should allow corporate managers to hire auditors. In addition, our result casts doubt on auditor designation.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.41 no.11
• /
• pp.1554-1558
• /
• 2012

Method development and validation of ellagic acid for the standardization of Gochang Bokbunja as a functional ingredient and health food were accomplished. A Symmetry$^{(R)}$ (C18, $4.6{\times}250mm$, $5.0{\mu}m$) column was used with a gradient elution system of 1% formic acid in water and acetonitrile. This method was validated according to specificity, linearity, accuracy, precision test, and recovery test. Specificity was confirmed with identical retention time, and calibration curves of ellagic acid showed good linear regression ($R^2$ >0.9996). Relative standard deviations (RSD) of data from the intra- and inter-day experiments were less than 2.28% and 2.84%, except in the low limit of quality control (LLOQ, $1{\mu}g/mL$) sample. The results of the recovery test were from 89.17% to 97.92% with RSD values from 0.05 to 0.14%. Therefore, we performed analysis of ellagic acid as a marker compound in Gochang Bokbunja extracts. The amount of ellagic acid in Gochang Bukbunja was about $1.918{\mu}g/mg$ (0.192%) in the three times analysis, and RSD was less than 2.36% by the validated method. These results suggest that the developed HPLC method is simple, efficient, and could contribute to the quality control of Gochang Bokbunja extract as a functional ingredient.

• Korean Chemical Engineering Research
• /
• v.49 no.2
• /
• pp.168-174
• /
• 2011

Various La-based perovskite catalysts were prepared by a Pechini method, and they were applied to the low-temperature oxidation of odor compounds exhausted from waste food treatment process for effective deodorization. Quantitative and qualitative analyses of exhausted gas were conducted to measure the amount of major odor compounds with respect to operation time. A standard odor sample composed of major odor compounds was then prepared for use as a feed for oxidation reaction system. Various transition metal(M)-substituted La-based perovskite catalysts ($LaMO_{3}$: M=Cr, Mn, Fe, Co, and Ni) were prepared and applied to the oxidation of odor compounds in order to investigate the $LaNiO_3$ catalyst showed the best catalytic performance. Pt-substituted perovskite catalysts ($LaNi_{1-x}Pt_{x}O_{3}$: x=0, 0.03, 0.1, and 0.3) were then prepared for enhancing the catalytic performance. It was found that $LaNi_{0.9}Pt_{0.1}O_{3}$ catalyst served as the most efficient catalyst. Supported perovskite catalysts ($XLaNi_{0.9}Pt_{0.1}O_{3}/Al_{2}O_{3}$: X=perovskite content(wt%), 0, 10, 20, 30, 40, 50, and 100) were finally applied for the purpose of maximizing the catalytic performance of perovskite catalyst in the low-temperature oxidation reaction. Catalytic performance of $XLaNi_{0.9}Pt_{0.1}O_{3}/Al_{2}O_{3}$ catalysts showed a volcano-shaped curve with respect to perovskite content. Among the catalysts tested, $20LaNi_{0.9}Pt_{0.1}O_{3}$/$Al_{2}O_{3}$ catalyst exhibited the highest conversion of odor compounds of 88.7% at $180^{\circ}C$.

• Journal of Hospice and Palliative Care
• /
• v.8 no.2
• /
• pp.163-172
• /
• 2005

Purpose: This study is to identify the effect of a death education program to the nursing students on their anxiety of death and attitudes toward nursing care of the dying. Methods: The design of this study is nonequivalent control group pretest-posttest design. The subjects of experimental group 20 and control group 16 in senior grade of department of Nursing G university in J city. The experimental group had Death education Program, which was a three days per week program, for 2 weeks. And post-test was carried out in the same way as the pre-test. Data analysis was done using frequency, percentage, mean, standard deviation, Chi-square test, t-test, paired Sample t-test using with SPSS win 10.0. Results: the experimental group was decreased in degree of anxiety of death and was improved in degree of positive attitudes toward nursing care of the dying. Conclusion: The death Education Program can be an effective nursing education program for their Nursing students to decrease their death anxiety and to prepare care of the dying.

• International Journal of Vascular Biomedical Engineering
• /
• v.4 no.2
• /
• pp.19-24
• /
• 2006

Background: Pulse wave velocity (PWV), which is inversely related to the distensibility of an arterial wall, offers a simple and potentially useful approach for an evaluation of cardiovascular diseases. In spite of the clinical importance and widespread use of PWV, there exist no standard either for pulse sensors or for system requirements for accurate pulse wave measurement. Objective of this study was to assess the reproducibility of PWV values using a newly developed PWV measurement system in healthy subjects prior to a large-scale clinical study. Methods: System used for the study was the PP-1000 (Hanbyul Meditech Co., Korea), which provides regional PWV values based on the measurements of electrocardiography (ECG), phonocardiography (PCG), and pulse waves from four different sites of arteries (carotid, femoral, radial, and dorsalis pedis) simultaneously. Seventeen healthy male subjects with a mean age of 33 years (ranges 22 to 52 years) without any cardiovascular disease were participated for the experiment. Two observers (observer A and B) performed two consecutive measurements from the same subject in a random order. For an evaluation of system reproducibility, two analyses (within-observer and between-observer) were performed, and expressed in terms of mean difference ${\pm}2SD$, as described by Bland and Altman plots. Results: Mean and SD of PWVs for aorta, arm, and leg were $7.07{\pm}1.48m/sec,\;8.43{\pm}1.14m/sec,\;and\;8.09{\pm}0.98m/sec$ measured from observer A and $6.76{\pm}1.00m/sec,\;7.97{\pm}0.80m/sec,\;and\;\7.97{\pm}0.72m/sec$ from observer B, respectively. Between-observer differences ($mean{\pm}2SD$) for aorta, arm, and leg were $0.14{\pm\}0.62m/sec,\;0.18{\pm\}0.84m/sec,\;and\;0.07{\pm}0.86m/sec$, and the correlation coefficients were high especially 0.93 for aortic PWV. Within-observer differences ($mean{\pm}2SD$) for aorta, arm, and leg were $0.01{\pm}0.26m/sec,\;0.02{\pm}0.26m/sec,\;and\;0.08{\pm}0.32m/sec$ from observer A and $0.01{\pm}0.24m/sec,\;0.04{\pm}0.28m/sec,\;and\;0.01{\pm}0.20m/sec$ from observer B, respectively. All the measurements showed significantly high correlation coefficients ranges from 0.94 to 0.99. Conclusion: PWV measurement system used for the study offers comfortable and simple operation and provides accurate analysis results with high reproducibility. Since the reproducibility of the measurement is critical for the diagnosis in clinical use, it is necessary to provide an accurate algorithm for the detection of additional features such as flow wave, reflection wave, and dicrotic notch from a pulse waveform. This study will be extended for the comparison of PWV values from patients with various vascular risks for clinical application. Data acquired from the study could be used for the determination of the appropriate sample size for further studies relating various types of arteriosclerosis-related vascular disease.

• Korean Journal of Biological Psychiatry
• /
• v.9 no.2
• /
• pp.140-151
• /
• 2002

Object and Method:Minor physical anomalies(MPAs) are frequently seen in patients with schizophrenia. MPAs are considered to arise from the anomalous development of ectoderm-originated tissues in the developing fetus. Since the central nervous system originates from ectoderm, MPAs can be regarded as externally observable and objective indicators of the aberrant development which might have taken place in the central nervous system. To investigate whether MPAs are more frequent in schizophrenic patients, the frequencies of MPAs were compared between schizophrenic patients and normal controls. Total 245 schizophrenic patients diagnosed with DSM-IV(male : 158, female : 87), and 418 normal control subjects(male : 216, female : 202) were included in this study. The MPAs were measured using the modified Waldrop scale with fifteen items in six bodily regions; head, eye, ear, mouth, hand, and foot. Result:The total scores of Waldrop scale were $4.40{\pm}1.93$($mean{\pm}standard$ deviation) in patients and $3.43{\pm}1.68$ in controls for females, and for males, $4.58{\pm}1.75$ in patients and $4.28{\pm}1.59$ in controls. For females, the excess of MPAs in schizophrenic patients was statistically significant(t-test : p<0.001). For males, schizophrenic patients also showed more MPAs than normal controls, but this tendency did not reach statistical significance (t-test : p=0.094). When the modified Waldrop total scores excluding head circumference were compared, the total scores in schizophrenic patients were significantly higher for both male and female subjects(t-test : male p<0.001, female p=0.001). The individual anomaly items included in Waldrop scale were also investigated. The items of epicanthus, hypertelorism, malformed ears, syndactylia were significantly more frequent in schizophrenic patients. In contrast, the items of adherent ear lobes, asymmetric ears, furrowed tongue, curved fifth finger, single palmar crease and big gap between toes did not show any differences in frequency between schizophrenic patients and normal controls. Since a lot of statistical analyses showed different results between male and female subjects, it seems to be necessary to consider gender as an important controlling variable for the analysis, however only the item of head circumference showed statistically significant gender-related difference according to log-linear analysis. Conclusion:With a relatively large sample size, the frequencies of MPAs enlisted in Waldrop scale were compared between schizophrenic patients and normal controls in this study. MPAs were more frequently seen in schizophrenic patients and, especially, several specific items in the Waldrop scale showed prominent excess in schizophrenic patients. Although definite conclusions cannot be drawn due to the inherent limitation of the study using Waldrop scale, these results seem to support the possibility that aberrant neurodevelopmental process might be involved in the pathogenesis of schizophrenia in some of the patients.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2000.04a
• /
• pp.9-10
• /
• 2000

An important business-field of world-wide steel-industry is the coating of thin metal-sheets with zinc, zinc-aluminum and aluminum based materials. These products mostly go into automotive industry. in particular for the car-body. into building and construction industry as well as household appliances. Due to mass-production, the processing is done in large continuously operating plants where the mostly cold-rolled metal-strip as the substrate is handled in coils up to 40 tons unwind before and rolled up again after passing the processing plant which includes cleaning, annealing, hot-dip galvanizing / aluminizing and chemical treatment. In the liquid Zn, Zn-AI, AI-Zn and AI-Si bathes a combined action of corrosion and wear under high temperature and high stress onto the transfer components (rolls) accounts for major economic losses. Most critical here are the bearing systems of these rolls operating in the liquid system. Rolls in liquid system can not be avoided as they are needed to transfer the steel-strip into and out of the crucible. Since several years, ceramic roller bearings are tested here [1.2], however, in particular due to uncontrollable Slag-impurities within the hot bath [3], slide bearings are still expected to be of a higher potential [4]. The today's state of the art is the application of slide bearings based on Stellite\ulcorneragainst Stellite which is in general a 50-60 wt% Co-matrix with incorporated Cr- and W-carbides and other composites. Indeed Stellite is used as the bearing-material as of it's chemical properties (does not go into solution), the physical properties in particular with poor lubricating properties are not satisfying at all. To increase the Sliding behavior in the bearing system, about 0.15-0.2 wt% of lead has been added into the hot-bath in the past. Due to environmental regulations. this had to be reduced dramatically_ This together with the heavily increasing production rates expressed by increased velocity of the substrate-steel-band up to 200 m/min and increased tractate power up to 10 tons in modern plants. leads to life times of the bearings of a few up to several days only. To improve this situation. the Mechanical Alloying (MA) TeChnique [5.6.7.8] is used to prOduce advanced Stellite-based bearing materials. A lubricating phase is introduced into Stellite-powder-material by MA, the composite-powder-particles are coated by High Energy Milling (HEM) in order to produce bearing-bushes of approximately 12 kg by Sintering, Liquid Phase Sintering (LPS) and Hot Isostatic Pressing (HIP). The chemical and physical behavior of samples as well as the bearing systems in the hot galvanizing / aluminizing plant are discussed. DependenCies like lubricant material and composite, LPS-binder and composite, particle shape and PM-route with respect to achievable density. (temperature--) shock-reSistibility and corrosive-wear behavior will be described. The materials are characterized by particle size analysis (laser diffraction), scanning electron microscopy and X-ray diffraction. corrosive-wear behavior is determined using a special cylinder-in-bush apparatus (CIBA) as well as field-test in real production condition. Part I of this work describes the initial testing phase where different sample materials are produced, characterized, consolidated and tested in the CIBA under a common AI-Zn-system. The results are discussed and the material-system for the large components to be produced for the field test in real production condition is decided. Outlook: Part II of this work will describe the field test in a hot-dip-galvanizing/aluminizing plant of the mechanically alloyed bearing bushes under aluminum-rich liquid metal. Alter testing, the bushes will be characterized and obtained results with respect to wear. expected lifetime, surface roughness and infiltration will be discussed. Part III of this project will describe a second initial testing phase where the won results of part 1+11 will be transferred to the AI-Si system. Part IV of this project will describe the field test in a hot-dip-aluminizing plant of the mechanically alloyed bearing bushes under aluminum liquid metal. After testing. the bushes will be characterized and obtained results with respect to wear. expected lifetime, surface roughness and infiltration will be discussed.

• Korean Journal of Psychosomatic Medicine
• /
• v.27 no.2
• /
• pp.77-84
• /
• 2019

Objectives : The Illness Intrusiveness Rating Scale (IIRS) is a well-validated self-report instrument for assessing negative impact of chronic illness and/or adverse effects of its treatment on everyday life domains. Although extensive literature probed its psychometric properties in medical illness, little attention was paid for its validity for psychiatric population. This study aimed to test factorial structure of the Korean Version of the IIRS (IIRS-K) in a consecutive sample of psychiatric outpatients. Methods : Data set of 307 first-visit patients of psychiatric clinic at Guri Hanyang univ. Hospital were used. Exploratory and confirmatory factor analysis, internal consistency were tested in IIRS-K. We also checked Spearman's correlation analysis between IIRS-K, Zung's self-report anxiety scale and Zung's self-report depression scale. Results : 76.9% of the patients were with anxiety disorder and depressive disorder. The principal component factor analysis of the IIRS-K extracted three-factor structure accounted for 63.2% of total variance that was contextually similar to the original English version. This three-factor solution showed the best fit when tested confirmatory factor analysis compared to the original IIRS, two-factor model of IIRS-K suggested from medical outpatients, and one-factor solution. The IIRS-K also showed good internal consistency (Cronbach's α=0.90) and good convergent validity with anxiety and depression scales. Conclusions : The IIRS-K showed the three-factor structure that was similar but not identical to original version. Overall, this study proved factorial validity of the IIRS-K and it can be used for Korean clinical population.