• Design & Manufacturing
• /
• v.14 no.1
• /
• pp.1-7
• /
• 2020

In this study, the variation of the shrinkage in the thickness direction of the molded parts according to the gate size of the polymer core fabricated through the 3D printer using the SLS method was studied. The polymer cores are laser sintered and the powder material is nylon base PA2200. The polymer cores have lower heat transfer rate and rigidity than the metal core due to the characteristics of the material. Therefore, the injection molding test conditions are set to minimize the deformation of the core during the injection process. The resin used in the injection molding test is a PP material. The packing condition was set to 80, 90 and 100% of the maximum injection pressure for each gate size. The runner diameter used was ∅3mm, and the gates were fabricated in semicircle shapes with cross sections 1, 2, and 3 ㎟, respectively. Thickness measurement was performed for 10 points at 2.5 mm intervals from the point 2.5 mm away from the gate, and the shrinkage to thickness was measured for each point. The shrinkage rate according to the gate size tends to decrease as the cross-sectional area decreases as the maximum injection pressure increases. The average thickness shrinkage rate was close to 0% when the packing pressure was 90% for the gate area of 1mm2. When the holding pressure was set to 100%, the shrinkage was found to decrease by 3% from the standard dimension due to the over-packing phenomenon. Therefore, the smaller the gate, the more closely the molded dimensions can be molded due to the high pressure generation. It was confirmed that precise packing process control is necessary because over-packing phenomenon may occur.

• The Journal of Korean Academy of Prosthodontics
• /
• v.34 no.4
• /
• pp.746-754
• /
• 1996

The purpose of this study was to evaluate the fracture strength of porcelain laminate veneer with various lingual extention length when incisal restoring. Sixty recently extracted, intact maxillary incisors were used and stored in a physiologic saline solution from the time of extraction. Seating form was preparation at the labial surface of each tooth with a water-cooled round diamond bur. Standard block was formed with 32 gauge and 24 gauge wax at tooth labial and lingual surface. Lingual extention length differed according to each group. (group I : 0.5mm, group II : 1 mm, group III : 2mm, group IV : 0mm) All tooth specimens were impressioned with examix(GC Inc., Japan). Refractory cast were maked with refractory die material(Ceramco Inc., U.S.A.) Laminate porcelain (Ceramco II Veneer porcelain, Ceramco Inc., U.S.A.) was condensed in refractory die cast and baked according to the manufacturer's recommendations. Each surface was contoured with low speed diamond bur according to guide block. All porcelain specimens were sandblasted and ultrasonically cleaned in distlled water for 3 minutes. Then, all porcelain specimen were etched with 8% hydrofluoric acid for 5 minutes. Sixty specimens were bonded with composite resin cement(Choice Porcelain Veneer System, Bisco Inc., U.S.A.) according to manufacture's directions. The fracture loads of the specimen were measured by Instron universal testing machine. The mean values of fracture loads for the groups were statistically compared by Duncan's multiful range test. The result were as follows : Mean fracture strengths of each group were 86.95Mpa in no lingual extention group, 44.98Mpa in 0.5mm lingual extention group, 27.47Mpa in 1mm lingual extention group, 19.61Mpa in 2mm lingual extention group. There was a statistically significant difference between all group(p<0.01).

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.1
• /
• pp.113-119
• /
• 2013

Despite rapid changes in the structure of industry, manufacturing remains a key industry for economic progress, promotion of trade, increased employment, and the creation of new industries. Production technologies are essential for strengthening the competitiveness of small- and medium-sized manufacturing industries. However, it is very difficult to standardize and systematically propagate production technology from an experienced worker to an inexperienced worker because these technologies are generally improved by the skilled people in a workshop. In this study, we introduce a Web-based platform system consisting of a knowledge authoring tool, technology database, semantic database, and Web portal service for sharing production technologies for the exterior housing parts of mobile products. By investigating various cellular phone designs, reference form factors for three types of mobile phone housings were designed based on the standard features. In addition, several manufacturing technologies and considerable information such as reference mold designs and molding conditions optimized using CAE and recent R&D outputs are stored in this system.

• Korean Chemical Engineering Research
• /
• v.62 no.1
• /
• pp.80-86
• /
• 2024

This study was conducted to evaluate the potential of rape stalk (RAS) as a raw material for the production of solid bio-fuels. RAS was immersed in an aqueous solution with acetic acid concentration of 1 percent, The content of reducing sugars separated from the RAS was analyzed. Glucose showed the highest content followed by xylose, galactose, arabinose and mannose. The immersed and non-immersed RAS were used for producing pellets with a pilot-scaled flat-die pellet mill. Bulk density and calorific values of the pellets improved with the use of the immersed RAS and the addition of wood particles. The values exceeded the minimum requirements for the A-grade of non-woody pellets (≧600 kg/m³ & ≧ 14.5 MJ/kg) designated by the ISO. Ash content of the pellets reduced with the immersion of RAS and the value satisfied the A-grade level (≦6.0%) of the ISO standard. The durability of the immersed RAS-based pellets was much higher than that of non-immersed IRS-based pellets, and the values were increased with the addition of wood particles. However, the durability did not meet the acceptance level for the B-grade of non-woody pellets (≧96.0%) designated by the ISO. These results suggested that the addition of binders in the production of non-woody pellets using an RAS immersed in acetic acid-based aqueous solution is required for the commercialization of the pellets.

• ETRI Journal
• /
• v.26 no.3
• /
• pp.229-240
• /
• 2004

This paper reports on our development of a dual-mode transceiver for a CMOS high-rate Bluetooth system-onchip solution. The transceiver includes most of the radio building blocks such as an active complex filter, a Gaussian frequency shift keying (GFSK) demodulator, a variable gain amplifier (VGA), a dc offset cancellation circuit, a quadrature local oscillator (LO) generator, and an RF front-end. It is designed for both the normal-rate Bluetooth with an instantaneous bit rate of 1 Mb/s and the high-rate Bluetooth of up to 12 Mb/s. The receiver employs a dualconversion combined with a baseband dual-path architecture for resolving many problems such as flicker noise, dc offset, and power consumption of the dual-mode system. The transceiver requires none of the external image-rejection and intermediate frequency (IF) channel filters by using an LO of 1.6 GHz and the fifth order onchip filters. The chip is fabricated on a $6.5-mm^{2}$ die using a standard $0.25-{\mu}m$ CMOS technology. Experimental results show an in-band image-rejection ratio of 40 dB, an IIP3 of -5 dBm, and a sensitivity of -77 dBm for the Bluetooth mode when the losses from the external components are compensated. It consumes 42 mA in receive ${\pi}/4-diffrential$ quadrature phase-shift keying $({\pi}/4-DQPSK)$ mode of 8 Mb/s, 35 mA in receive GFSK mode of 1 Mb/s, and 32 mA in transmit mode from a 2.5-V supply. These results indicate that the architecture and circuits are adaptable to the implementation of a low-cost, multi-mode, high-speed wireless personal area network.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.8
• /
• pp.31-40
• /
• 2009

This paper presents a design of a high performance DC-DC boost converter as a power module for SOC designs. It applied to this chip that reduced inductor and capacitor for integrating on a chip, and it operates with a switching frequency of 100MHz. It has reliability and stability in high switching frequency. The controller of DC-DC boost converter is designed by voltage-mode control method and compensated properly. The designed DC-DC converter is fabricated with the 0.18${\mu}m$ standard CMOS technology with a thick-gate oxide option. The overall die size is 8.14$mm^2$, and controller size is 1.15$mm^2$. The converter has the maximum efficiency over 76% for the output voltage of 4V and load current larger 300mA. The load regulation is 0.012% (0.5mV) for the load current change of 100mA.

• Journal of IKEEE
• /
• v.15 no.1
• /
• pp.57-63
• /
• 2011

This paper presents a tunable band pass filter (BPF) for multi bio-signal detection. The bandwidth can be controlled by the bias current of transconductance (gm), while conventional BPF exploited switchable capacitor array for band selection. With this design technique, the die area of proposed BPF reduced to at least one tenth the area of conventional design. The simulation results show the high cut-off frequency tuning range of from 100Hz to 1Khz. The circuit was implemented with a 0.18um CMOS standard technology. Total current consumption is 1uA at the supply voltage of 1V with sub-threshold design technique.

• Journal of IKEEE
• /
• v.20 no.2
• /
• pp.192-195
• /
• 2016

In this paper, we present a nanopower CMOS bandgap voltage reference working in sub-threshold region without resisters and bipolar junction transistors (BJT). Complimentary to absolute temperature (CTAT) voltage generator was realized by using two n-MOSFET pair with body bias circuit to make a sufficient amount of CTAT voltage. Proportional to absolute temperature (PTAT) voltage was generated from differential amplifier by using different aspect ratio of input MOSFET pair. The proposed circuits eliminate the use of resisters and BJTs for the operation in a sub-1V low supply voltage and for small die area. The circuits are implemented in 0.18um standard CMOS process. The simulation results show that the proposed sub-BGR generates a reference voltage of 290mV, obtaining temperature coefficient of 92 ppm/$^{\circ}C$ in -20 to $120^{\circ}C$ temperature range. The circuits consume 15.7nW at 0.63V supply.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.1
• /
• pp.127-138
• /
• 1991

A gear forming method by cold extrusion and an analytical method with its numerical solution program based on the upper bound method were developed. In the analysis the involute curve was as a shape of die and the upper bound method was used to calculate energy dissipation rate. By this method the power requirement and optimum conditions necessary for extruding helical(spur) gear were successfully calculated. These numerical solutions are in good agreement with experimental data. In the experiment, 4-6 class helical gear of KS standard for automobile transmission was successfully manufactured.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.5 s.305
• /
• pp.43-50
• /
• 2005

This paper describes some IC(integrated circuits) design and implementation techniques of low power multi-band Gm-C bandpass filter for body composition analyzer. Proposed BPF(bandpass filter) can be selected from three bands(20 KHz, 50 KHz, 100 KHz) by control signal. To minimize die area, a simple center frequency tuning scheme is used. And to reduce power consumption, operational transconductance amplifier operated in the sub-threshold region is adopted. The proposed BPF is implemented with 0.35 um 2-poly 3-metal standard CMOS technology Chip area is $626.42um\;{\times}\;475.8um$ and power consumption is 700 nW@100 KHz.