• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.80-83
• /
• 1999

Rigid Plasticity Finite Element Analysis is developed for the shapes of dead metal zone and the curving velocity distribution in the eccentric square dies extrusion. The shape of dead metal zone is defined as the boundary surface with the maximum friction constant between the deformable zone and the rigid zone. The curving phenomenon in the eccentric square dies is caused by the eccentricity of square dies. The deviated velocity is changed with the distance form the center of cross-section of the workpiece. The results show that the curving of products and the shapes of the dead metal zone are determined by Rigid Plasticity Finite Element Analysis and that the curvature of the extruded products increases with the eccentricity.

• Steel and Composite Structures
• /
• v.20 no.3
• /
• pp.487-500
• /
• 2016

In order to investigate the flexural bearing capacity of panel zone of diaphragm-through joint between concrete filled square steel tubular column and steel beam, four specimens were tested under static tension loads to study the mechanical properties and bearing capacity of diaphragm-through joints with a failure mode of panel zone. Finite element models of these specimens were developed to simulate the test and compare the predicted failure modes, load-displacement curves and bearing capacities with the experimentally observed. It was found that the tensile load from the steel beam flange is mainly shared by the square steel tube and the diaphragm. The diaphragm plastic zone appears along the cross-section lines enclosed by the square steel tube and the influence of steel beam web on the plastic zone of the steel tube is significant and cannot be neglected. Computational models of yield lines on square steel tube and diaphragm are established based on the distribution pattern of the plastic zone, and an analytical method for the evaluation of the bearing capacity of the joint is proposed. The theoretical results and the experimental data are compared and found in good agreement.

• Proceeding of Spring/Autumn Annual Conference of KHA
• /
• 2011.04a
• /
• pp.147-152
• /
• 2011

The purpose of this study is to find out the commercialization cause of 2nd class residential area in urban center as basic research to protect urban residential area against the pressure of commercialization. Through the research that are based on literature, field survey and urban planning map, it analysed the commercialization cause of selected two sites under similar urban condition ; to be a nearby subway station and to be a famous commercial street in site, etc. The consequences of this study are summarized as follows ; First the distance between subway station and residential block and residential commercialization are in inverse proportion each other. Second, the corner lot of a block and the access street directly connected collector street are very important factors to spread commercialization to residential area. Finally, nevertheless first and second results, there is square zone which is very high rate of commercialization within one regardless the distance between subway and residential block. the maximum range of square zone is assumed about 250 meter based on case study.

• Journal of the Korean housing association
• /
• v.14 no.4
• /
• pp.57-67
• /
• 2003

The purpose of the study is to propose the basic data for an aged residential building suitable for Korean environment and it is based on the outcomes of investigation on The Aged Care Residential Service in Australia including the scale and arrangement of private zone and specific characteristics of each compartment. The brief outcomes of the research are follows as. - The Aged Care Residential Services have been functionally running divided into Nursing home, Hostel and Retirement Village by the classification standard of the residential classification scale. - Single bed rooms have 75% of total residential area and the square of single bed room is about $20\textrm{m}^2$and that of two-bed room is about $31\textrm{m}^2$. - There are two types of ensuite such as one single-bed room and one ensuite and bed room for two or three persons and ensuite type. The square of ensuite varies as single is 50∼60%, single for public is 25∼30%, and double for public is 15∼20%. - Assisted bathrooms are generally located in the middle of building and it is suggested to be occupied about $1.25\textrm{m}^2$ per person. Sitting rooms are two types such as room type whose square has about $12\textrm{m}^2$ and a lounge type has $16\textrm{m}^2$.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.3
• /
• pp.1-8
• /
• 2001

In the DS/CDMA mobile communication systems, the parallel interference canceller is used in order to reduce the multiple access interference and the multipath fading. It is needed the accurate interference estimate in the multistage parallel cancellation. In this paper, the adaptive cancellation method and the new tentative decision device arc proposed and the performance is analyzed. The adaptive cancellation method uses the normalized least mean square(NLMS) algorithm to calculate the weight adaptively, and new tentative decision device uses the hyperbolic tangent decision with null zone. Computer simulation shows that the proposed scheme has the improved performance and the number of user is increased 48% compared with the conventional receiver.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.3
• /
• pp.216-222
• /
• 2016

Generation of a quiet zone in noisy environment is undoubtedly of considerable realistic significance. This paper describes development and implementation of a multichannel real-time active noise control (ANC) system for 3 dimensional noisy environment to enhance the quiet zone performance in terms of size and noise cancellation gain. The proposed ANC system employes a multichannel delay-compensated filtered-X least mean square (FXLMS) algorithm; its real-time implementation is designed in TMS320C6713 digital signal processor (DSP) board. The system is evaluated for cancelling various tonal frequency noises in the range from 100 to 500 Hz, and the performance is then illustrated by measuring the quiet zone in terms of sound pressure level (SPL) attenuation. Experiment results show that a quiet zone of quiet with satisfactory size and maximum 24 dB noise attenuation is successfully generated.

• Smart Structures and Systems
• /
• v.28 no.6
• /
• pp.761-777
• /
• 2021

This study presents a numerical investigation on the sensitivity of electromechanical (EM) impedance responses to inner damaged concrete of a prestressed anchorage zone. Firstly, the Ottosen yield criterion is selected to simulate the plasticity behavior of the concrete anchorage zone under the compressive loading. Secondly, several overloading cases are selected to analyze inner damage formations in the concrete of the anchorage zone. Using a finite element (FE) model of the anchorage zone, the relationship between applied forces and stresses is analyzed to illustrate inner plasticity regions in concrete induced by the overloading. Thirdly, EM impedance responses of surface-mounted PZT (lead-zirconate-titanate) sensors are numerically acquired before and after concrete damage occurrence in the anchorage zone. The variation of impedance responses is estimated using the RMSD (root-mean-square-deviation) damage metric to quantify the sensitivity of the signals to inner damaged concrete. Lastly, a novel PZT skin, which can measure impedance signatures in predetermined frequency ranges, is designed for the anchorage zone to sensitively monitor the EM impedance signals of the inner damaged concrete. The feasibility of the proposed method is numerically evaluated for a series of damage cases of the anchorage zone. The results reveal that the proposed impedance-based method is promising for monitoring inner damaged concrete in anchorage zones.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.1
• /
• pp.99-104
• /
• 2010

Magnesium and magnesium alloys, the lightest structural materials, have been received plenty of global attention recently. These alloys could be applied in various fields, especially the electronics industry, because of their excellent electromagnetic interference shielding. However, the welding technique of magnesium alloys has not been established. This study is related to the welding of AZ31B magnesium alloy by a short-pulsed a Nd:YAG laser. Two types of pulse waves, square pulse and variable pulse, were used to control weld defects. Results show that the crack and porosity, generated in the weld, had not been controlled by general square pulse. But through the application of variable pulse, the defects could be prevented and the good weld zone was obtained.

• International Journal of Computer Science & Network Security
• /
• v.24 no.3
• /
• pp.142-150
• /
• 2024

A conceptual model represents an understanding of a system that is going to be developed, which in this research, a driving simulation software to study driver behavior at signalised intersections. Therefore, video observation was conducted to study driver compliance behaviour within the dilemma zone at signalised intersection, with regards to driver's distance from the stop line during yellow light interval. The video was analysed using Thematic Analysis and the data extracted from it was analysed using Chi-Square Independent Test. The Thematic Analysis revealed two major themes which were traffic situation and driver compliance behaviour. Traffic situation is defined as traffic surrounding the driver, such as no car in front and behind, car in front, and car behind. Meanwhile, the Chi-Square Test result indicates that within the dilemma zone, there was a significant relationship between driver compliance behaviour and driver's distance from the stop line during yellow light interval. The closer the drivers were to the stop line, the more likely they were going to comply. In contrast, drivers showed higher non-compliant behavior when further away from stop line. This finding could help in the development of conceptual model of driving simulation with purpose in studying driver behavior.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.27 no.5
• /
• pp.605-612
• /
• 1994

The methods to determine the hydrodynamic coefficients for the fixed type artificial reefs which were constructed to control ecological system in coastal waters are compared and discussed by model test results. To calculate the wave forces, least square method show good agreement with the experimental results and more stability than maximum force component method or Fourier decomposition method. This modified least square method of weighting the square of measured force turned out to be the most feasible method for maximum force. Using the feasible method, hydrodynamic characteristics for artificial reefs on uniform slopes offshore and breaking zone were studied. They were properly related to Keulegan-Carpenter's number and found larger than previous results. Wave force coefficients for artificial reefs around breaking zone were distributed from 1.5 to 2.5, and the mean value was 2.0. Drag force components were more in evidence than inertia force in maximum force which is important parameter to evaluate stability for high-permeability structures. A formula for the calculation of the maximum force for artificial reefs design is proposed, using structural dimension, water particle velocity and Keulegan-Carpenter's number.