• Korean Chemical Engineering Research
• /
• v.47 no.5
• /
• pp.572-579
• /
• 2009

This study is to investigate experimentally the flame structure and propagation mechanism in dust explosions and to provide the fundamental knowledge. Upward propagating laminar dust flames in a vertical duct of 1.8 m height and 0.15 m square cross-section are observed and flame front is visualized using by a high-speed video camera. Also, the thicknesses of preheated and reaction zone have been determined by a schlieren, electrostatic probe and thermocouple. The thickness of preheated zone in lycopodium dust flame is observed to be 4~13 mm, about several orders of magnitude higher than that of premixed gaseous flames. From the experimental results by a PIV(Particle Image Velocimetry) system, a certain residence time of the unburned particle in preheated zone is needed to generate combustible gas from the particle. The residence time will depend on preheated zone thickness, particle velocity and flame propagation velocity.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.8A
• /
• pp.950-961
• /
• 2004

In this paper, we measured and analyzed propagation characteristics in a subway tunnel that is recently increasingly becoming one of the radio communication environments. The measurements are carried out in a subway tunnel with frequency bands of 2.45㎓ and 5.8㎓. The length of tunnel we used for this study is 175m of LOS (Line-of-sight) and 270m of NLOS (Non Line-of-Sight). The subway tunnel is curved and its cross section is horseshoe type. The measurement systems we employ in this study are a narrow-band system and a wide-band system. The narrow-band system is used to get path loss measurement and the wide-band system is used to figure out delay profile measurement. In particular, the wide-band system consists of 1023 length PN sequence generator using a chip rate of 80MHz based on a sliding correlation technique. The omni-directional antennas and directional antennas are used to analyze propagation characteristics for beam type of antenna. The path loss displays only pure path loss of a tunnel environment. The delay profile indicates the mean excess delay and RMS (root mean square) delay spread.

• The Journal of Korean Physical Therapy
• /
• v.14 no.1
• /
• pp.39-53
• /
• 2002

Objectives: The objective of this study was to investigate the prevalence rate and factors related with low back pain(LBP) in senior high school teachers. Methods: Questionnaires were completed by 405 teachers at 13 high school in Andong city in July 2-14, 2001. The information was used to estimate odds ratio(OR) and 95% confidence intervals(CI) for factors relation to LBP prevalence. A cross-section study design was used in this study. Results: The pointprevalence rate for LBP was 26.4%, prevalence rate for 6 months was 36.0%, prevalence rate for 1 year was 36.5%, and experience rate during life time was 55.1%, The factors associated with LBP by Chi-square test were marital status(p=0.014), An angle for back rest of car seat(p=0.014), and vibration of seat (p=0.003), 12.2% for patients with LBP was a higher than 6.0% for without in singles, Patients(29.0%) were higher than no patients(17.8%) in above $100^{\circ}$. 14% for patients who exposed to a high vibration. Vibration significantly associated with point prevalence rate for LBP were marital status and lecture time in logistic analysis. The married teachers had a higher LBP experience than singles(OR=2.6, 95% CI 1.13-6.03). The teachers who have a lot of lecture time in a day had a higher experience than those for less time(OR=1.6, 95% CI 1.42-2.51). Conclusions: Results from this study indicate that a statistical significant factors relation to LBP were marital status and lecture time in a day.

• Journal of the Korean Institute of Gas
• /
• v.15 no.5
• /
• pp.13-18
• /
• 2011

Experimental studies were carried out to investigate the characteristics of explosion mitigations by varying concentrations of agar gel barriers in an explosion chamber, 1400 mm in length, with a square cross-section of $100{\times}100mm^2$. Another extension chamber, $100{\times}100{\times}300mm^3$, was made to hold a gel barrier. Four different gel concentrations were used in the measurements: 2, 3, 4, 5 %(by weight of gel). Displacement of the gel barrier was measured using a high speed camera, and pressure development was measured using pressure transducers and a data acquisition system. It was found that as the concentrations of the gel barriers increased, the gel rupture time and the time taken to reach the maximum pressure increased. It was also found that the increment of gel concentrations increased the reduction percentage in the maximum pressure between before and after gel barrier.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.20 no.5
• /
• pp.472-481
• /
• 2008

In this study hydraulic experiment was carried out to investigate the flow characteristics in the submerged outlet structure of Boryeong power plant and the efficiency of bubble reduction by installing horizontal porous plate in the outlet structure. The cross-sectional mean velocity in the submerged outlet structure was smaller than 1 m/s, the target value at the design stage to prevent bubble outflow to the open sea area. In addition, it was found that the maximum depth of bubble penetration is reduced 30 to 50% by installing the horizontal porous plate at the second falling location in the submerged outlet structure. It is expected that the total bubble amount entrained in the water will be most efficiently reduced by installing square-hole-shape porous plate of 20 cm hole size and making its central section as non-porous structure to dissipate the energy of falling water.

• Structural Engineering and Mechanics
• /
• v.53 no.5
• /
• pp.939-956
• /
• 2015

In this study, in order to propose an efficient model to predict the torque capacity of steel fiber reinforced concrete (SFRC) beams, the existing experimental data related to torsional response of beams is reviewed. It is observed that existing data neglects the effects of some parameters on the variation of torque capacity. Thus, an experimental research was also conducted to obtain the effects of neglected parameters. In the experimental study, a total of seventeen SFRC beams are tested against torsion. The parameters considered in the experiments are concrete compressive strength, steel fiber aspect ratio, volumetric ratio of steel fibers and longitudinal reinforcement ratio. The effect of each parameter is discussed in terms of torque versus unit angle of twist graphs. The data obtained from this experimental research is also combined with the data got from previous studies and employed in artificial neural network (ANN) analysis to estimate the ultimate torque capacity of SFRC beams. In addition to parameters considered in the experiments, aspect ratio of beam cross-section, yield strengths of both transverse and longitudinal reinforcements, and transverse reinforcement ratio are also defined as parameters in ANN analysis due to their significant effects observed in previous studies. Assessment of the accuracy of ANN analysis in estimating the ultimate torque capacity of SFRC beams is performed by comparing the analytical and experimental results. Comparisons are conducted in terms of root mean square error (RMSE), mean absolute error (MAE) and coefficient of efficiency ($E_f$). The results of this study revealed that addition of steel fibers increases the ultimate torque capacity of reinforced concrete beams. It is also found that ANN is a powerful method and a feasible tool to estimate ultimate torque capacity of both normal and high strength concrete beams within the range of input parameters considered.

• Journal of the Korean Ceramic Society
• /
• v.40 no.8
• /
• pp.715-719
• /
• 2003

The Aerosol Deposition (AD) process will be proposed as a new fabrication technology for the integrated RF modules. $\alpha$-A1$_2$O$_3$ thick films were successfully grown on glass and Al substrates at room temperature by the AD process. Relative dielectric permittivity and loss tangent of the $Al_2$O$_3$ thick films on Al showed 9.5 and 0.005, respectively. To form microstrip lines on aerosol-deposited A1903 thick films, copper electroplating and lithography processes were employed, and the square-type cross section with sharp edges could be obtained. Low-pass LC filters with 10 GHz cutoff frequency were simulated by an electromagnetic analysis, exhibiting the validity of the AD process as a fabrication technology f3r integrated RF modules.

• Journal of architectural history
• /
• v.21 no.2
• /
• pp.7-20
• /
• 2012

As the corner of wooden pagoda forms the roof by closely bordering left and right eaves on the various purlins and angle rafters, it is designed for every face to be recognized as front whose structure system increases load to bear proportionally. The corner of wooden pagoda is inseparable with the corner bracket set as it becomes stable thanks to the corner bracket set structurally and load burden under restrained structure makes the corner bracket set really important. Accordingly, this study could figure out some facts by analyzing corner bracket sets of Palsangjeon of Beobjusa Temple in Korea, Seokgatap of Bulgungsa Temple in China and Ojungtap of Beobryungsa Temple in Japan which were constructed with pure wooden structure. This study demonstrated that corner bracket set played a pivotal role in keeping balance of concentrated load of corner (corner of opening) in each floor that contributed to the stability of wooden pagoda structurally despite multiple duplications of floors and also figured out the outfit of corner bracket set was subject to the floor type and the cross section of Gongpo installed on top of Pyeongju. Wooden pagodas in 3 countries were two floor types of octagon and square, and employed different connection method between upper and lower floors. The difference between floor and duplication method determines the method of corner, but even different methods were sufficient to have entirety in every side by completing dynamic principle of corner bracket set even though old method had to solve the problem of concentrated load and it also confirms that it was essential Gongpo to prevent any deformation of corner.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.1
• /
• pp.19-28
• /
• 2011

As a preview study, present research analysed the performance characteristics of a velocity compound supersonic impulse turbine with the rotor overlaps before adapting the overlap has the best turbine performance. This research was conducted for the turbine with square cross-section nozzles instead of axisymmetric nozzles and wrap around nozzles. Through 3-dimensional flow analysis for the turbine by a commercial flow analysis package, tip overlap case was more effective to improve the turbine performance than case hub overlap, and overlap case applied the hub and tip of the rotor had the largest improvement for the turbine performance in the cases. In case of overlap for the 2nd stage rotor, improvement of the turbine performance was not visibly large. Because, generated power in the 2nd stage is 22~23% of whole generated turbine power.

• Korean Journal of Optics and Photonics
• /
• v.27 no.5
• /
• pp.174-180
• /
• 2016

A tunable optical delay line is designed, fabricated, and characterized. The tunable delay line consists of four polymer-ring add/drop filters with delay waveguides between adjacent ones. The polymer waveguide is a buried structure, designed to be square with core width and height of $1.8{\mu}m$. The refractive indices of the core and cladding polymer are 1.48 and 1.37 respectively. The large index difference and small cross section of the waveguide enable us to realize a compact device using a small radius of curvature. Four pairs of electrodes are evaporated above the add/drop filters to provide heating currents for thermal tuning. In measurements we can identify variable time delays of 110, 225, and 330 ps in proportion to the number of delay lines.