• International Journal of Highway Engineering
• /
• v.19 no.4
• /
• pp.37-44
• /
• 2017

PURPOSES : Conductive and convective heat transfer simulations for an asphalt mixture were made by using discrete element method (DEM) and similarity principle. METHODS : In this research, virtual specimens composed of discrete element method particles were generated according to four different predetermined particle size distribution curves. Temperature variations of the four different particles for a given condition were estimated and were compared with measurements and analytical solutions. RESULTS : The virtual specimen with mixed particles and with the smallest particle show very good agreement with laboratory test results and analytical solutions. As particle size decreases, better heat transfer simulation can be performed due to smaller void ratio and more contact points and areas. In addition, by utilizing the similarity principle of thermal properties and corresponding time unit, analytical time can be drastically reduced. CONCLUSIONS : It is concluded that the DEM asphalt mixture specimens with similarity principle could be used to predict the temperature variation for a given condition. It is observed that the void ratio has critical effect on prediction of temperature variation. Comparing the prediction for a 4 mm particle specimen with a mixed particle specimen, it is also concluded that predicting the mixed particle specimen temperature is much more efficient considering the number of particles that are directly associated with computational time in DEM analysis.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.2
• /
• pp.451-462
• /
• 1995

Single overload tests performed to examine the crack retardation behavior for the specimen thickness and overload ratios. Delayed crack length was tend to increase in small thickness and big overload ratio but was difference between delayed crack length and plastic zone size that expected in specimen thickness. So retardation behavior that estimated in plastic zone size, was not sufficient. Crack tip branching and striation distribution, secondary mechanisms that effected in retardation behavior, was examined by experiment and finite element analysis. Crack tip branching was affected by micro structure, and appeared the more complicatedly according to increasing damage by overload and decreasing crack driving force in base line stress level. And crack tip branching the branching angle decreased crack driving force in the crack tip. And a characteristic of the fractography on retardation zone was that striation distribution did not appear due to decreased crack driving force.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2006.11a
• /
• pp.95-98
• /
• 2006

This study investigates spalling properties of high performance concrete, 60MPa clan, made with the various types of coarse aggregate and adding ratio of polypropylene(PP) fiber. As experimental parameters, totally sixteen specimens of ${\phi}100{\times}200mm$ in size are prepared: one specimen for control without fiber, ten specimens with different coarse aggregate types, along with 0.05, 0.1, 0.15 percent of PP fiber in each. 1 hour fire test is conducted and then spalling appearance, spalling degree and residual compressive strength are examined. In addition, sit specimens made with two types of coarse aggregate site, along with same adding ratio of fiber are supplementally done, and only spalling properties is examined. Test results showed that control concrete and most specimens containing 0.05% of PP fiber exhibited 4 to 3 level of spalling degree, resulting severe explosive spalling, except for the specimen using basalt aggregate(Bc) showing 2 to 3 level of that. Especially, the Bc specimen containing 0.1% of the fiber exhibited that residual compressive strength value was 32%, which is 10% higher than other specimens using limestone or granite. Spalling resistance performance was also effective as aggregate size increase.

• Geomechanics and Engineering
• /
• v.18 no.1
• /
• pp.49-58
• /
• 2019

The effect of microstructure on the permeability of two saturated marine clays was studied through a series of falling head permeability tests and mercury intrusion porosimetry (MIP) tests. The key findings from this experimental study include the following results: (1) The permeability of undisturbed specimens is larger than that of reconstituted specimens at the same void ratio due to different soil fabrics, i.e., the pore size distributions (PSDs), even though they have the similar variation law in the permeability versus void ratio. (2) Different permeabilities of undisturbed and reconstituted specimens at the same void ratio are mainly caused by the difference in void ratio of macro-pores based on the MIP test results. (3) A high relevant relation between $C_k$ ($C_k$ is the permeability change index) and $e*_{10}$, can be found by normalizing the measured data both on undisturbed or reconstituted specimens. Hence, the reference void ratio $e*_{10}$, can be used as a reasonable parameter to identify the effect of soil fabric on the permeability of saturated soft clays.

• Korean Journal of Materials Research
• /
• v.28 no.10
• /
• pp.570-577
• /
• 2018

This study examines the effect of microstructural factors on the strength and deformability of ferrite-pearlite steels. Six kinds of ferrite-pearlite steel specimens are fabricated with the addition of different amounst of Mn and V and with varying the isothermal transformation temperature. The Mn steel specimen with a highest Mn content has the highest pearlite volume fraction because Mn addition inhibits the formation of ferrite. The V steel specimen with a highest V content has the finest ferrite grain size and lowest pearlite volume fraction because a large amount of ferrite forms in fine austenite grain boundaries that are generated by the pinning effect of many VC precipitates. On the other hand, the room-temperature tensile test results show that the V steel specimen has a longer yield point elongation than other specimens due to the highest ferrite volume fraction. The V specimen has the highest yield strength because of a larger amount of VC precipitates and grain refinement strengthening, while the Mn specimen has the highest tensile strength because the highest pearlite volume fraction largely enhances work hardening. Furthermore, the tensile strength increases with a higher transformation temperature because increasing the precipitate fraction with a higher transformation temperature improves work hardening. The results reveal that an increasing transformation temperature decreases the yield ratio. Meanwhile, the yield ratio decreases with an increasing ferrite grain size because ferrite grain size refinement largely increases the yield strength. However, the uniform elongation shows no significant changes of the microstructural factors.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.30 no.2
• /
• pp.82-94
• /
• 1988

The purpose of this study is to introduce the Double Punch test method which is an indirect testing method of tensile strength of concrete, and to compare with the tensile strength of concrete as determined by the split-cylinder test, a practical method for performing the Double Punch test to obtain the tensile strength of concrete is proposed and recommended for general use. In this study, the dimensions of cylindrical specimens used in the Double-Punch test were 15X30cm, 15X15cm, 10${\times}$(20cm, and 5${\times}$l0cm, and in the split-cylinder test were 15${\times}$(30cm, 15${\times}$(15cm, and 10${\times}$(20cm. And the diameters of loading punches used in the Double-Punch test were 1.5cm, 2.5cm, and 3.5 cm. The results obtained from tests are summarized as follows ; 1. In the split-cylinder test, the tensile strength of concrete by the linear elasticity theory is similar to that of plasticity theory. 2. Both split-cylinder test and Double-Punch test, tensile strength of concrete is increased with decreasing specimen size. This tendency is identical when the ratio of specimen diameter to height is 1: 2, but that tendency is quite different when the ratio is 1: 3. In the Double-Punch test, if specimen size is constant, by increasing the punch size, tensile strength of concrete is increased, too. 4. Using a 15 ${\times}$( 15 cm cylinder specimen and 3.5 cm diameter punch in the Double Punch test would give the most uniform and consistent result in tensile strength, and the result showed a gQod correlation with splitting tensile strength from 15 x 30cm specimen. 5. In order to obtain satisfactory results and to nuninuze variability, it is proposed that specimens of 15 cm in diameter and 15 cm in height with two 3.5 cm diameter punches should be used. It seems, therefore, reasonable tt) take f't=0.0024 P(kg / cm$^2$) as a working formula for computing the tensile strength in the Double Punch test for concrete.

• Journal of the Society of Disaster Information
• /
• v.13 no.3
• /
• pp.366-375
• /
• 2017

Internal factors having effects on compressive strength test results of concrete include size, shape, height-diameter ratio(h/d), section processing method, dryness and wetness, etc. of the specimen. As it is difficult to ensure dimensions of core specimen due to rebar cutting from rebar spacing, wall thickness, effects on the structure, etc. when taking core of the concrete structure, correction of dimensions and h/d of the specimen become important for quality control of the concrete. Thus, in order to review effects of specimen size and height-diameter ratio for the concretes with compressive strength within 40~60MPa, this study has experimentally reviewed compressive strength test values by applying correction factors pursuant to KS F 2422 (Method of obtaining and testing drilled cores and sawed beams of concrete), when changing specimen diameter to ${\emptyset}5{\sim}15cm$, and h/d to 2.0~1.25.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.6
• /
• pp.867-876
• /
• 1987

Corrosion fatigue fracture with change in the grain size of M.E.F. dual phase steel is investigated in 3.5% NaCI aqueous solution at pH 2, 4, 6, 9, and 11. Generally speaking, decrease in corrosion fatigue life is strongly dependent on decrease in pH and slightly on the grain size. For the B material with the big grain size, the fatigue life is small due to its large reduction ratio of corrosion fatigue life. The influence of grain size on the reduction ratio of corrosion fatigue life is large at pH 11-6. Whi9le at pH 4-2 the reduction ratio of corrosion fatigue life only depends on the corrosion effect. The larger grain size and the lass pH result in the greater influence on corrosion fatigue crack propagation rate. As pH decreases, the plateau portion in the crack propagation rate curves of the B material are distinct. Crack propagation rate curves become slow down at high .DELTA.K range because crack closure effect by minute corrosion products inside crack causes the oxidation corrosion action less effective for a certain period of time. In A material with small grain size, fatigue life is increased in proportion with increase of martensite intergranular which brings forth restraining the crack propagation decreases crack propagation rate. Corrosion pit which is created in the surface of specimen is found at pH 6,4 and 2 which is noticeable and the unevenness of the surface of the specimen becomes severe as pH decreases. The unevenness of corrosion fatigue fracture surface is severe as the effect of pH increases i.e. as pH decreases. In proportion with increase in the grain size and decrease in pH, the aspect of brittle fracture becomes evident.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10b
• /
• pp.873-878
• /
• 2000

Tension stiffening effects of reinforced concrete member with large diameter bar, mainly used at reactor building of nuclear power plant, are studied by uniaxial structural tests. Bond length and stress of steel bar, size of steel bar, and compressive strength of concrete are evaluated to tension stiffening by uniaxial tests. Problems and solution during the uniaxial test are suggested. The prevent splitting cracks, concrete cover-to-bar diameter ratio $c/d_{b}$ is kept 2.6~2.8. Because the bond length is increased as the size of steel bar, the specimen length of the D35 steel bar is required at least 2.0 m. The specimen length must be decided with bond length as well as concrete cover-to-bar diameter ratio to prevent splitting crack.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.11
• /
• pp.1691-1698
• /
• 1989

Gas sensing effects produced by adsorptive reaction between specimen surface and gases are expected to be influenced greatly by the state of the speimen surface. In this study, Co1-xMgxO ceramics oxygen sensors were prepared by pressing at 0.3-1.5ton/cm\ulcornerwith or without binder, intending to change porosity and average grain size on the surface purposely. The composition ratio of CoO to MgO was fixed at 1:1(mol.%). Microstructure of prepared Co0.5Mg0.5O ceramics were observed, the electrical properties and the sensitivity characteristics for oxygen gas were investigated in the device temperature range of 700-1000\ulcorner and for oxygen partical pressure range of 1-10**-4 atm. Temperature dependence of the resistivity of the specimen showed NTC behavior, average grain size increased and porosity decreased with increasing compaction pressure. The slope of the resistivity of the specimen on the oxygen partial pressure decreased with increasing average grain size and with decreasing porosity. Particularly, specimen pressed by 0.3 and 0.5 ton/cm\ulcornershowed the highest sensitivity to oxygen gas.