• Nuclear Engineering and Technology
• /
• 제34권1호
• /
• pp.90-103
• /
• 2002

The thermal and mechanical properties of compacted bentonite and bentonite-sand mixture were collected from the literatures and compiled. The thermal conductivity of bentonite is found to increase almost linearly with increasing dry density and water content of the bentonite. The specific heat can also be expressed as a function of water ontent, and the coefficient of thermal expansion is almost independent on the dry density. The logarithm of unconfined compressive strength and Young’s modulus of elasticity increase linearly with increasing dry density, and in the case of constant dry density, it can be fitted to a second order polynomial of water content. Also the unconfined compressive strength and Young’s modulus of elasticity of the bentonite-sand mixture decreases with increasing sand content. The Poisson’s ratio remains constant at the dry density higher than 1.6 Mg/m$_3$, and the shear strength increases with increasing dry density.

• Journal of the Korean Wood Science and Technology
• /
• 제25권2호
• /
• pp.61-66
• /
• 1997

Paulownia wood has been used as sound board for Korean traditional musical instruments such as Keomungo(Korean lute), Kayagum(twelve-stringed Korean harp) and Changgu(hour-glass shaped drum), etc. The acoustic properties of wood affected not only by dimensions but also by density and stiffness of wood. Due to inhomogeneity and hygroscopicity of wood. the acoustic properties of wood are inconsistent. To clarify the effect of moisture content and air dry density on acoustic properties, longitudinal vibration experiment was accomplished in 3 moisture content levels of 9.6, 11.1 and 12.5% and in 3 air dry density levels of 0.22, 0.25 and 0.28g/$cm^3$. The results were as follows: As the moisture content increased, the fundamental frequency. specific dynamic Young's modulus and sound velocity decreased, but the internal friction increased so that loss of energy increased. The values in damping of sound radiation were rapidly decreased at 12.5%. It meant that the damping of internal friction was larger than damping of sound radiation at high moisture content. As the air dry density increased, the fundamental frequency, specific dynamic Young's modulus and sound velocity increased, but the internal friction and damping of sound radiation decreased so that loss of energy decreased. And acoustic converting efficiency was hardly influenced by increasing air drying density.

• 한국가구학회지
• /
• 제10권1호
• /
• pp.57-63
• /
• 1999

This study was carried out to analyze the relationship between basic physical properties and acoustical characteristics of imported violin wood and to offer the information on raw material procurement and incoming-material quality control to domestic violin makers which have purchased most raw materials from European exporting countries at high expense. Equilibrium moisture content of European spruce with lower specific gravity after the prolonged storage was rather higher than that of European maple with higher specific gravity. The specific gravity of spruce increased with decreasing annual ring width, however, that of narrower annual ring. Increasement in specific gravity enhanced the dynamic Young's modulus of both wood species, but influenced the vibration energy loss by internal friction differently between two species. For dynamic MOE, qurater-sawn spruce was higher than the flat-sawn, but maple showed the reverse directional characteristics. Consequently, it would be well for violin makers to establish the standard for materials and quality control system to assure the quality of their violin products.

• 한국주조공학회지
• /
• 제17권1호
• /
• pp.51-57
• /
• 1997

Effects of the amount of flake type graphite, morphology and (V,Mo)carbides on the specific damping capacity of austenitic low thermal expansion cast irons were investigated. Specific damping capacity(SDC) of low thermal expansion cast irons increased with the increased amount of graphite. Specific damping capacity of low thermal expansion cast iron decreased with the increased Young's modulus. In the case of V and Mo addition, SDC decreased with the increased amount of carbides. Specific damping capacity increased about 2% by the movement of magenetic domains which appeared in ferromagnetic materials.

• 지질공학
• /
• 제18권4호
• /
• pp.371-379
• /
• 2008

본 연구에서는 경기도 일대의 편마암지역 11곳에서 다운홀(down-hole) 탄성파탐사를 이용하여 획득한 탄성파속도를 이용, 편마암지역에서의 탄성파 속도와 동탄성계수와의 상관성을 조사하였다. 연구결과 편마암에서의 탄성파속도의 특성은 $V_s=0.5589{\times}V_p$ 상관관계를 보여준다. 탄성파 속도와 동탄성계수와의 상관관계는 두 개의 군으로 분리된다. 풍화가 진행됨에 따라 첫 번째 군은 암석의 비중에 큰 영향을 받지만 두 번째 군에서는 절리면의 간격에 영향을 받는다. 풍화가 진행됨에 따라 첫 번째 군은 감소하는 경향을 보인다. 경암반에서의 압축파속도($V_p$) 동탄성계수($E_d$, $G_d$, $K_d$)의 상관관계는 선형으로 분석되었지만, 보통암반에서의 압축파속도($V_p$)와 동탄성계수($E_d$, $G_d$, $K_d$)의 상관관계는 2차 함수 포물선 곡선의 형태를 띠는 것으로 분석되었다. 전단파속도($V_s$)와 동탄성계수($E_d$, $G_d$, $K_d$)의 상관관계 또한 압축파속도($V_p$)와 유사한 결과를 보이는 것으로 분석되었다.

• Fibers and Polymers
• /
• 제7권4호
• /
• pp.372-379
• /
• 2006

The surface topography, tensile properties, and thermal properties of ramie fibers were investigated as reinforcement for fully biodegradable and environmental-friendly 'green' composites. SEM micrographs of a longitudinal and cross sectional view of a single ramie fiber showed a fibrillar structure and rough surface with irregular cross-section, which is considered to provide good interfacial adhesion with polymer resin in composites. An average tensile strength, Young's modulus, and fracture strain of ramie fibers were measured to be 627 MPa, 31.8 GPa, and 2.7 %, respectively. The specific tensile properties of the ramie fiber calculated per unit density were found to be comparable to those of E-glass fibers. Ramie fibers exhibited good thermal stability after aging up to $160^{\circ}C$ with no decrease in tensile strength or Young's modulus. However, at temperatures higher than $160^{\circ}C$ the tensile strength decreased significantly and its fracture behavior was also affected. The moisture content of the ramie fiber was 9.9 %. These properties make ramie fibers suitable as reinforcement for 'green' composites. Also, the green composites can be fabricated at temperatures up to $160^{\circ}C$ without reducing the fiber properties.

• Journal of the Korean Wood Science and Technology
• /
• 제44권2호
• /
• pp.274-282
• /
• 2016

This aims of this study were to investigate the relationship between non-destructive evaluation (NDE) and actual bending properties of particleboard, and to predict the bending properties of three-layer particleboard. Three kinds of raw materials, i.e. Hinoki (Chamaecyparis obtusa Endl.) strand, knife-milled Douglas-fir (Pseudotsuga manziesii (Mirb) Franco), and hammer-milled matoa (Pometia spp.) obtained from wooden industry, were utilized as furnish for experimental panel with methylene diphenyl diisocyanate (MDI) resin as binder. The NDE test was conducted by hit sounds using an FFT analyzer according to the spectrum peak of wave frequency, while the static bending test was conducted according to JIS A-5908. The results reveal that the dynamic Young's modulus as an NDE test has a potential for being used to predict the elastic bending of particleboards by a specific equation for adjusting its proper values. The values of NDE and static test are significantly different with a deviation range at 3-20%. The bending stiffness of three-layer particleboards manufactured from different wood species is predictable by observing the bending stiffness of two elements based on the thickness of its layers. The predicted values of bending stiffness and static test are significantly different with a deviation range at 5-24%.

• 지구물리
• /
• 제3권2호
• /
• pp.127-138
• /
• 2000

시멘트 모르타르 재료에 대한 동탄성계수와 정탄성계수의 차이를 고찰하고자 일곱 단계의 물시멘트 혼합비에 대해 다양한 길이의 시료를 제작, 시험하였다. 이들 시료의 동탄성계수 및 정탄성계수는 비중 측정, 초음파 전파 속도 측정 및 일축 압축 시험을 통해 결정되었으며, 시료에 대해 측정된 P파 및 S파 속도 분석은 기존의 아날로그 방식이 아닌 디지털 방식을 통해 수행되었다. 일련의 자료 처리 과정을 지친 디지털 방식 자료는, 초음파 전파 속도를 정밀하게 분석하는데 결정적인 역할을 할 수 있음이 확인되었으며, 복수 시료를 이용한 거리 변화에 따른 파의 지연 시간 변화를 이용한 속도 산정 방식이, 단일 시료 길이와 전파 시간을 이용한 기존 속도 산정 방식보다 더욱 정밀한 값을 보여주는 것으로 판명되었다. 밀도는 시료의 P파 및 5파 속도와 뚜렷한 양의 상관성을 보여주며, 일축 압축 강도 역시, 밀도와 뚜렷한 양의 상관성을 보여준다. 초음파 전파 속도를 통해 측정된 동탄성계수$(E_D)$와 일축 압축 시험을 통해 측정된 정탄성계수$(E_S)$의 비율$(E_D/E_S)$은 시료의 강도가 커질수록 함께 커지는 경향을 보여주었으며, 모든 시료에 대해 항상 동탄성계수가 정탄성계수보다 높게 평가됨이 확인되었다. 그러나 동포아송비$({\nu}_D)$와 정포아송비$({\nu}_S)$의 비율$({\nu}_D/{\nu}_S)$은 강도와 특별한 상관성을 보여주지 않았으며, 그 비율도 $69{\sim}122\;%$정도로 동포아송비와 정포아송비가 큰 차이를 보이지 않는 것으로 나타났다.

• 한국연초학회지
• /
• 제5권2호
• /
• pp.63-69
• /
• 1983

The tensile strength (Pm) . elongation percentage ($\varepsilon$) , elastic modulus (I) , and specific volume (Sv) were calculated from the data of tensile characteristics of By 104 .and Burley 21 tobacco leaves, which were measured over a relative humidity from 60 to 80% at $20\pm2^{\circ}C$.The important results obtained were as follows.(1) Tensile strength(Pm) The "Pm"of By 104 was greater than that of Burley at. The "Pm"in both varieties were increased toward the upper stalk position and according to the decrease of relative humidity. The "Pm" of parallel piece to tile vein in a leaf were greater than that of right angle piece to the vein. (2) Elongation percentage ($\varepsilon$). The "s" of By 104 was higher than that of Burley 21. The "s" in both varieties were increased toward the upper stalk position and according to the increase of relative humidity. The "s" of parallel Piece to the vein in a Burley leaf was greater than that of right angle piece to the vein. (3) Elastic modulus (E) The "E" of Burley 21 leaf was higher than that of By 104. The "E" in both varieties were increased toward the lower stalk position and according to decrease of relative humidity. The "E"of parallel piece to the vein in both varieties leaves were greater than that of right angle piece to tile vein. (4) Specific volume (Sv) The "Sv" of Burley 21 leaf was increased than that of By 104. The "Sv" in both varieties were increased toward the lower stalk position and according to the decrease of relative humidity.ot;Sv" in both varieties were increased toward the lower stalk position and according to the decrease of relative humidity.dity.

• 터널과지하공간
• /
• 제21권1호
• /
• pp.33-40
• /
• 2011

본 연구에서는 온도와 수압이 암석의 물성 변화에 미치는 영향을 평가하였다. 온도가 암석의 물성에 미치는 영향을 평가하기 위하여 가곡광산에서 채취한 화강암과 석회암 시험편에 200, 300, 400, 500, 600, $700^{\circ}C$(석회암의 경우 $700^{\circ}C$는 제외하였음)의 열을 가하여 예열시험편을 제작하였다. 예열시험편에 대한 실내실험을 통해 비중, 유효공극률, 탄성파속도, 일축압축강도, 탄성계수, 포아송비를 측정한 결과 온도가 증가함에 따라 화강암과 석회암 예열시험편의 물성이 변하는 것으로 나타났다. 비중, 유효공극률, 탄성파속도의 급격한 변화는 화강암의 경우 $400^{\circ}C$ 이상에서 발생하였으며, 석회암의 경우에는 $300^{\circ}C$ 이상에서 나타났다. 온도에 따른 일축압축강도, 탄성계수, 포아송비의 변화도 물리적 특성의 변화와 유사한 것으로 나타났다. 예열시험편의 일축압축강도와 탄성계수로부터 유추한 500, 600, $700^{\circ}C$ 화강암 예열시험편의 GSI는 각기 81, 66, 58로 나타났으며, 400, 500, $600^{\circ}C$ 석회암 예열시험편의 GSI는 각각 76, 71, 65로 나타났다. 500, 600, $700^{\circ}C$ 화강암 예열시험편과 400, 500, $600^{\circ}C$ 석회암 예열시험편에 7.5 MPa의 수압을 가하였다. 수압을 적용한 예열시험편의 유효공극률, 탄성파속도, 일축압축강도, 탄성계수를 측정하여 평균한 결과 수압을 가하기 전 예열시험편에 비해 평균 감소량이 화강암 500, 600, $700^{\circ}C$ 예열시험편 각각에 대해서 7.6, 11.3, 14.9%로 나타났고, 석회암 400, 500, $600^{\circ}C$ 예열시험편에 대해서는 각기 8.2, 13.8, 21.9%로 평가되었다.