• The KIPS Transactions:PartC
• /
• v.15C no.2
• /
• pp.79-86
• /
• 2008

MANET(Mobile Ad hoc Network) is a collection of two or more nodes equipped with wireless communications and constrained by the factor of energy limitation. The running out of energy on some nodes may bring down the performance of network seriously. For solving the problems above, this paper uses completely separated Node-Disjoint multipaths from a source to a destination as many as possible. And, based on average, minimum or variance of energy values on the each multipath, the packets are distributed on paths. Generally, collecting methods for energy information can be classified into two main categories, Static and Dynamic. As the different energy values collected, the packet distribution methods are classified into six criteria, Static-Average, Static-Minimum, Static-Variance, Dynamic-Average, Dynamic-Minimum and Dynamic-Variance respectively. The performance of the packet distribution methods and that of AODV are compared by NS2 simulation.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.4
• /
• pp.376-381
• /
• 2011

CVT(Continuously Variable Transmission) is one of the most promising candidates for the future automobile transmission because of its continuously variable gear ratio and reduced shift shock. It is also possible to operate the power source at its high efficiency region with CVT. The CVT system consists of thrust plate, driving pulley, belt, driven pulley, and preload spring of output shaft. In this paper, the dynamic modeling of a CVT system is completed to obtain the static performances of CVT system. A simulator is implemented on Matlab(Simulink), which can analyse the static performances of a CVT system. The methods for improving the total efficiency of a motorcycle system are also proposed based on the simulation results. In this study we increase the capacity factor of CVT up to the three times of default specification.

• Proceedings of the KIEE Conference
• /
• 1999.07c
• /
• pp.1039-1041
• /
• 1999

Recently Advanced Static Var Compensators(ASVC) or STATic Synchronous COMpesator(STATCOM) has been considered as a next generation reactive power controller. [2] STATCOM is a voltage source inverter(VSI) based static VAr compensator with only small capacitors on the do side. The main function of the STATCOM is to keep the bus voltage magnitude at the desired value. [1] This paper compares the PAM STATCOM with PWM STATCOM. The characteristics and the control method of each model is analyzed. And the simulation of STATCOMs based on the above two methods was presented.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.49 no.7
• /
• pp.323-331
• /
• 2000

Recently Advanced Static Var Compensators(ASVC) or STATic Synchronous COMpesator(STATCOM) has been considered as a next generation reactive power controller. The STATCOM is a voltage source inverter(VSI) based on the static VAr compensator with only small capacitors on the dc side. The main function of the STATCOM is to keep the bus voltage magnitude at the desired value. This paper compared the PAM STATCOM with the PWM STATCOM. The characteristics and the control method of each model is analyzed. And the simulation of STATCOMs based on the above two methods is presented.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.5
• /
• pp.443-451
• /
• 2013

Acoustic emission(AE) has emerged as a powerful nondestructive tool to detect any further growth or expansion of preexisting defects or to characterize failure mechanisms. Recently, this kind of technique, that is an in-situ monitoring of inside damages of materials or structures, becomes increasingly popular for monitoring the integrity of large structures like a huge wind turbine blade. In this study, the activities of AE signals generated from external artificial sources was evaluated and located by new developed signal mapping source location method and this test is conducted by 750 kW full-scale blade. And a new source location method was applied to assess the damage in the wind turbine blade during step-by-step static load test. In this static loading test, we have used a full scale blade of 100 kW in capacity. The results show that the acoustic emission activities give a good agreement with the stress distribution and damage location in the blade. Finally, the applicability of the new source location method was confirmed by comparison of the result of source location and experimental damage location.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.587-590
• /
• 1991

It is general to make the circuit analysis of current-fed type inverter driven by current source with rippleless input under the assumption of infinite induction Ld in direct current reactor(DCL). This paper focusing on the fact that Ld has bounded value in real circuit, examines operating characteristics by analysis of static state characteristics of current type inverter driven by voltage source and compares it with the operating characteristics of the circuit driven by current source.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.6
• /
• pp.545-556
• /
• 1990

A design method of a current source using 12-pulse phase-controlled rectifier (PCR) is presented. The critical inductance of the 12-pulse PCR is derived and it is shown that the critical inductance can be reduced using a current source. The control circuit of the 12-pulse PCR with an inner fast dynamic loop is proposed to give the frequency synchronism and to reduce the subharmonics due to the unbalance of the transformer of the power line. This circuit is analyzed and its dynamic loop is optimized. The optimal constant PIMF (proportional, integral and measurable variable feedback, and feedforware) controller is also designed using the time-weighted quadratic performance index. It is shown via experimental results that the proposed design method gives high dynamic and static performance of the current source using the 12-pulse PCR.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.30 no.4
• /
• pp.735-743
• /
• 2020

Secure coding is a technique that detects malicious attack or unexpected errors to make software systems resilient against such circumstances. In many cases secure coding relies on static analysis tools to find vulnerable patterns and contaminated data in advance. However, secure coding has the disadvantage of being dependent on rule-sets, and accurate diagnosis is difficult as the complexity of static analysis tools increases. In order to support secure coding, we apply machine learning techniques, such as DNN, CNN and RNN to investigate into finding major weakness patterns shown in secure development coding guides and present machine learning models and experimental results. We believe that machine learning techniques can support detecting security weakness along with static analysis techniques.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.5
• /
• pp.1477-1485
• /
• 1996

Since the spindle bearing systme is the main source of the total cutting point compliance of machine tool structures, in this work, the static and dynamic characteristics of the spndle bearing systme driven by the gear located on the bearing span were investigated using analytical and finite elemtn methods to improve the performance of the spindle bearing system. Based on the theretical results, a specially designed prototype spindle bvearing systme was manufactured. Using the manufactured spindle bearing system, the static and dynamic characteristics were measured. From the comparison of the experimental results with the theoretical results, it was found that the finite elemetn method predicted well the static and dynamic characteristics of the spindle bearing system.

• Proceedings of the KIEE Conference
• /
• 2001.07a
• /
• pp.155-157
• /
• 2001

This paper presents an comparative study on the effect of SSSC and UPFC to the power system static analysis. SSSC is used to control active power flow in transmission lines by controlling the phase angle of the injected voltage source which is in rectangular to the line current. UPFC is used to control the magnitude and phase of the injected voltage sources which are connected both in series and in parallel with the transmission line to control power flow and bus voltage. To compare the effect of SSSC and UPFC in power system static analysis, the PSS/E simulation program is used. As the FACTS device model such as SSSC and UPFC is not provided in PSS/E yet, an equivalent load model is used. This procedure is implemented by IPLAN which is an external macro program of PSS/E. The simulation results show that UPFC is more effective to improve bus voltage than SSSC in power system static analysis.