• Korean Chemical Engineering Research
• /
• v.54 no.6
• /
• pp.806-811
• /
• 2016

Organosolv pretreatment is the process to frationation of lignocellulosic feedstocks to enhancement of enzymatic hydrolysis. This process has advantages that organic solvents are always easy to recover by distillation and recycled for pretreatment. The chemical recovery in organosolv pretreatment can isolate lignin as a solid material and carbohydrates as fermentable sugars. For the economic considerations, using of low-molecular-weight alcohols such as ethanol and methanol have been favored. When acid catalysts are added in organic solvent, the rate of delignification could be increased. Mineral acids (hydrochloric acid, sulfuric acid, and phosphoric acid) are good catalysts to accelerate delignification and xylan degradation. In this study, the biomass was pretreated using 40~50 wt% ethanol at $170{\sim}180^{\circ}C$ during 20~60 min. As a results, the enzymatic digestibility of 2-stage pretreatment of rigida using 50 wt% ethanol at $180^{\circ}C$ was 40.6% but that of 1-stage pretreatment was 55.4% on same conditions, therefore it is shown that the pretreatment using mixture of the organosolv and catalyst was effective than using them separately.

• Applied Chemistry for Engineering
• /
• v.10 no.4
• /
• pp.523-530
• /
• 1999

Acrylic pressure-sensitive adhesive has been made utilizing organic solvents, but nowadays it is made by solvent-free system due to environmental problems. In this study, emulsion polymerization were carried out at $40^{\circ}C$ with methacrylic acid(MAA), n-butyl acrylate(n-BA) and 2-ethylhexyl acrylate(2-EHA) as monomers in the presence of anionic(sodium dodecyl sulfate, SDS) and nonionic(ethylene oxide types) surfactant mixtures. The overall conversion of the polymerization reaction in a mixed surfactant system was found to be higher than that in a single surfactant system. Emulsion stability in mixed or anionic surfactant systems was found to be over 12 week, which was better than that in nonionic surfactant system. Emulsion particle size decreased as surfactant content increased. The Tg and molecular weight of emulsion polymer were inependent of the type, the amount and the mixing ratio of surfactant. Based on the results of stability and peel strength, the optimum nonionic surfactant ratio in total 4 g of surfactant mixture systems is found to be 40~60% by weight where the nonionic surfactant has 50 ethylene oxide groups and 16~18 carbon atoms in hydrophobic alkyl chain.

• Applied Chemistry for Engineering
• /
• v.5 no.3
• /
• pp.395-405
• /
• 1994

The various functional groups, such as hydroxyl(-OH), carboxyl(-COOH) and quinonic oxygen(OC<) on the carbon black(abbreviated to CB) surface were activated with n-butyl lithium solution in n-hexane and then acrylate and methacrylate monomers were graft polymerized onto these activated anionic sites and CB-grafted polymers were obtained. To separate homopolymers from reaction mixture, non-solvent precipitation method or centrifugal separating method were applied. Subsequently, conversion, grafting ratio and efficiency were determined at various reaction temperatures and times. In case of acrylates, the grafting ratio showed 20~30% but methacrylates showed 150~200%. Also the anion polymerizations between CB and monomers were nearly reached to equilibrium state within one or two hours under each reaction temperatures but conversion and grafting ratio were increased a little with reaction temperature increase. In colloidal dispersion stability test, before heat-drying, the all CB-grafted polymers showed good dispersed stability in good solvents for acrylic and methacrylic homopolymers. Futhermore, CB-polymethacrylates were found to show excellent collidal properties for good solvents of methacrylic homopolymer even after heat-drying. Identification of the grafted polyacrylates and polymethacrylates onto the CB surface was performed by FT-IR spectroscopy. In addition, electric resistance values of CB-grafted polymers were measured by Four-probe method, and the increase of the grafting ratio showed the increase of the surface resistance.

• Journal of Technologic Dentistry
• /
• v.22 no.1
• /
• pp.89-112
• /
• 2000

Although dental laboratory technicians are prone to be exposed to various work-related health hazardous materials such as dusts, chemicals, etc., the prevalence and nature of work-related health problems of them have not been a matter of great concern in the field of occupational health service in Korea. The purpose of the present investigation was to describe a collected profile of subjective health symptoms and their attributable factors in Korean dental laboratory technicians. A questionnaire listing five groups of health symptoms and five health symptom-related factors was mailed to randomly selected 1,900 dental laboratory technicians. Among them, 1,344 dental laboratory technicians filled out the questionnaires and returnde them. Five groups of health symptoms included musculoskeletal symptom, dermal symptoms, respiratory symptoms, eys symptoms, and ear symptoms. Five health symptom-related factors were occupational environment-related health risk factors, work history, health related habits and status, use of personal protective equipment and general characteristics. Detailed parameters of health risk factors were work posture, vibration, and chemical or physical hazards such as dust, fume, vapor, solvent, light, and noise for occupational environment-related factors; work place, area, number of employees, work hours, career, work part, and work load for work history; Broca's index, hours of sleep, eating, smoking, alcohol, exercise, health examination, and self assessed health status for health habits and status; face masks, goggles, and so on for use of personal protective equipment, and; age, sex, marital status, and education for general characteristics. Before the start of main survey, a pilot survey was carried out for validity and reliability tests of the questionnaire. All the data obtained were coded and analyzed with PC/SAS 6.12 program. The prevalence of health symptoms was the highest in musculoskelton (87.3%), and followde by eyes (78.9%), respiratory organs (64.3%), ears (57.8%), and skin (52.2%) in descending order. Statistically significant risk factors by multiple logistic regression analyses were sex, health examination, self assessed health status, and hand/finger posture in musculoskeletal symptoms; sex, self assessed health status, career, acid gas, and hand contact with resin mixture in deraml symptoms; Broka's smoking, exercise, self assessed health status, and face mask in respiratory symptoms; sex, hours of sleep, self assessed health status, work hours, work load, plaster dust, inadequate lighting, and goggle in eys symptoms, and eating, smoking, self assessed health status, and work load in ear symptoms. With the above considerations in mind, prevalence of subjective symptoms among Korean dental laboratory technicians was relatively high, and they were attributable to most of the occupational environment-related factors, work history, use of personal protective equipment, health habits and status, and general characteristics. Particularly, it is suggested that health promotion programs for promoting self- assessed health status and smoking cessation, preventive measures for protection of the female technicians’health, and reducing work load be necessary, since those factors were associated with more than one subjective symptom.

• Korean Journal of Materials Research
• /
• v.25 no.12
• /
• pp.719-726
• /
• 2015

For a decade, solution-processed functional materials and various printing technologies have attracted increasingly the significant interest in realizing low-cost flexible electronics. In this study, Cu nanoparticles are synthesized via the chemical reduction of Cu ions under inert atmosphere. To prevent interparticle agglomeration and surface oxidation, oleic acid is incorporated as a surface capping molecule and hydrazine is used as a reducing agent. To endow water-compatibility, the surface of synthesized Cu nanoparticles is modified by a mixture of carboxyl-terminated anionic polyelectrolyte and polyoxylethylene oleylamine ether. For reducing the surface tension and the evaporation rate of aqueous Cu nanoparticle inks, the solvent composition of Cu nanoparticle ink is designed as DI water:2-methoxy ethanol:glycerol:ethylene glycol = 50:20:5:25 wt%. The effects of poly(styrene-co-maleic acid) as an adhesion promoter(AP) on rheology of aqueous Cu nanoparticle inks and adhesion of Cu pattern printed on polyimid films are investigated. The 40 wt% aqueous Cu nanoparticle inks with 0.5 wt% of Poly(styrene-co-maleic acid) show the "Newtonian flow" and has a low viscosity under $10mPa{\cdots}S$, which is applicable to inkjet printing. The Cu patterns with a linewidth of $50{\sim}60{\mu}m$ are successfully fabricated. With the addition of Poly(styrene-co-maleic acid), the adhesion of printed Cu patterns on polyimid films is superior to those of patterns prepared from Poly(styrene-co-maleic acid)-free inks. The resistivities of Cu films are measured to be $10{\sim}15{\mu}{\Omega}{\cdot}cm$ at annealing temperature of $300^{\circ}C$.

• KSBB Journal
• /
• v.24 no.5
• /
• pp.446-452
• /
• 2009

Oleyl alcohol, butyl butyrate, and two different ionic liquids were evaluated for the extraction of butanol from culture broth without toxic effect to cells. The tested solvents showed more than 50% extraction efficiency, and oleyl alcohol was chosen as the best extractant for butanol among the used extractants with a partition coefficient of 2.89. When oleyl alcohol was used as an extractant, more than 80% of butanol was extracted in the wide range of butanol concentrations (1-20 g/L) and pH values (pH 4-5.5). In extractive fermentation using oleyl alcohol only, there was 11% more butanol production and glucose consumption when compared to that without extractive fermentation, implicating a reduced inhibitory effect of butanol due to butanol removal to the oleyl alcohol phase. In addition, oleyl alcohol did not inhibit cell growth, while a mixture of oleyl alcohol and butyl butyrate with the volume ratio of 9:1~7:3 inhibited either butanol production or cell growth significantly due to the toxicity of butyl butyrate to cells. In conclusion, oleyl alcohol can be used as an efficient and non-toxic solvent for extractive fermentation for butanol production.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1999.04a
• /
• pp.5-5
• /
• 1999

The Principal deficiency of the existing notion about the sintering-mixtures consists in the fact that almost no attention is focused on the Phenomenon of alloy formation during sintering, its connection with dimensional changes of powder bodies, and no correct ideas on the driving force for the sintering process in the stage of establishing chemical equilibrium in a system are available as well. Another disadvantage of the classical sintering theory is an erroneous conception on the dissolution mechanism of solid in liquid. The two-particle model widely used in the literature to describe the sintering phenomenon in solid state disregards the nature of the neighbouring surrounding particles, the presence of pores between them, and the rise of so called arch effect. In this presentation, new basic scientific principles of the driving forces for the sintering process of a two-component powder body, of a diffusion mechanism of the interaction between solid and liquid phases, of stresses and deformation arising in the diffusion zone have been developed. The major driving force for sintering the mixture from components capable of forming solid solutions and intermetallic compounds is attributed to the alloy formation rather than the reduction of the free surface area until the chemical equilibrium is achieved in a system. The lecture considers a multiparticle model of the mixed powder-body and the nature of its volume changes during solid-state and liquid-phase sintering. It explains the discovered S-and V-type concentration dependencies of the change in the compact volume during solid-state sintering. It is supposed in the literature that the dissolution of solid in liquid is realised due to the removal of atoms from the surface of the solid phase into the melt and then their diffusicn transfer from the solid-liquid interface into the bulk of liquid. It has been shown in our experimental studies that the mechanism of the interaction between two components, one of them being liquid, consist in diffusion of the solvent atoms from the liquid into the solid phase until the concentration of solid solutions or an intermetallic compound in the surface layer enables them to pass into the liquid by means of melting. The lecture discusses peculimities of liquid phase formation in systems with intermediate compounds and the role of the liquid phase in bringing about the exothermic effect. At the frist stage of liquid phase sintering the diffusion of atoms from the melt into the solid causes the powder body to grow. At the second stage the diminution of particles in size as a result of their dissolution in the liquid draws their centres closer to each other and makes the compact to shrink Analytical equations were derived to describe quantitatively the porosity and volume changes of compacts as a result of alloy formation during liquid phase sinteIing. Selection criteria for an additive, its concentration and the temperature regime of sintering to control the density the structure of sintered alloys are given.

• Korean Journal of Environmental Agriculture
• /
• v.21 no.2
• /
• pp.90-95
• /
• 2002

A study was carried out to optimize the cleanup step using a solid-phase extraction (SPE) cartridge, $SupelClean^{TM}$ Florisil, for multiresidue analysis of 16 pesticides in cucumber matrix. Eluting efficiencies of two solvent systems including acetone/n-hexane and ethyl acetate/n-hexane mixtures were critically evaluated by recoveries of target anaytes from the SPE Florisil column. Based on the recovery as a measure of eluting efficiency, an acetone/n-hexane (20/80,v/v) mixture provided more than 80% recovery for 15 pesticides except bifenthrin. In case of ethyl acetate/n-hexane, 14 pesticides showed recoveries higher than 75% while those far alachlor and bifenthrin were less than 30%.

• Korean Journal of Food Science and Technology
• /
• v.47 no.3
• /
• pp.281-285
• /
• 2015

An oleaginous fungus was isolated from soil and identified as Mortierella sp. (M-12) for producing arachidonic acid (AA). Cell disruption methods, extraction methods, and particle sizes of freeze-dried biomass were tested to achieve maximum extraction of total lipids and AA. M-12 grown in glucose yeast media at $25^{\circ}C$ for 7 days contained 35.5% total lipid, and 47% of the total lipid was AA. Lipid extraction yield from wet biomass was shown to be similar to that in a dry state. Maximum lipid extraction was achieved using a mixture of chloroform and methanol (2:1) as an extraction solvent. Different mechanical cell disruption methods did not affect lipid extraction yields. The smaller the particle size of the biomass, the better the lipid extraction yield was observed. Particle size of biomass was shown to more strongly affect lipid extraction than extraction time. The highest AA content was observed in the class of neutral lipids.

• Korean Journal of Food Science and Technology
• /
• v.34 no.2
• /
• pp.180-185
• /
• 2002

Volatile flavor components in three pear varieties (Pyrus pyriforia N.) of traditional cultivar, Bongri, Hwangsilri and Yongmokri, were collected by SDE method using the mixture of n-pentane and diethylether as an extract solvent and were identified by GC/MS. Among 97 compounds identified from all varieties, there were 72, 58 and 66 components in Bongri, Hwangsilri and Yongmokri, respectively. Ethyl acetate was the dominant constituent in all cultivars and also volatile profiles contained large quantity of ethanol and acetic acid. Butyl acetate identified as a main component in Bongri was not found in other pears, but in Hwangrilri and Yongmokri only 4 to 5 esters played important role in total volatile flavor composition. The volatile profiles of these three varieties were characterized by compounds in group of aldehydes, esters, alcohols, acids and ketones. As classified by functional group of separated and identified components, esters and alcohols in Bongri, alcohols in Hwangsilri, and esters in Yongmokri were roled as the title in composition of volatile flavor components. Although small amount, Yongmokri had the highest rate of volatile production at 6.552 mg/kg of pear while Hwangsilri produced the lowest at 4.175 mg/kg of pear.