• 한국수산과학회지
• /
• 제55권6호
• /
• pp.817-826
• /
• 2022

This study was conducted to determinean optimal soaking solution for inhibiting the texture softening of shrimp Litopenaeus vannamei pressured at high temperature (S-P/HT) in a retort, and also to optimize concentrations of 0.5% calcium chloride (CC) and 5.0% potato starch (PS) for preparation of a mixed solution (MS) and soaking time (ST) in the MS. On the basis of the results of expressible drip (4.6%), water holding capacity (95.1%), hardness (18.4 N/cm²) and sensory texture (7.2 score), the MS was found to be the optimal soaking solution for inhibition of texture softening under S-P/HT conditions, The concentrations of CC (X₁, %), PS (X₂, %), and ST (X₃, min) were selected as independent variables, and hardness (Y₁), springiness (Y₂) and sensory texture (Y₃) were selected as dependent variables. The optimal conditions of X₁, X₂, and X₃ were 0.51%, 6.34%, and 364 min, respectively. Under the optimal conditions, the experimental values of Y₁, Y₂ and Y₃ were 18.3±0.8 N/cm², 4.4±0.3 mm and 7.7±0.2, respectively, which did not diffr significantly from the predicted values (P>0.05). In conclusion, the optimized models of X₁, X₂, and X₃ for the preparation of S-P/HT using CC-PS were suitably fitted.

• 한국세라믹학회지
• /
• 제31권9호
• /
• pp.957-968
• /
• 1994

Manufacturing process of porous glass by the filler method was studied. Commercial soda-lime-silicate glass powder was mixed with inorganic salt as the filler such as KCl, K2SO4, Na2SO4. Sintering shrinkages of mixed powders with the variation of sintering temperature were compared, and the effects of the fillers to shrinkages of mixed powder were increased in the order of Na2SO4${\mu}{\textrm}{m}$ of pore diameter were manufactured when the filler sizes 100~200 ${\mu}{\textrm}{m}$. The open pore volume of porous glass is determined by the quantity of filler and porous glasses having open pore volume between 30 and 70 vol% are available. Available sintering temperature range for preparation of porous glass is from the softening temperature of the glass powder to eutectic melting temperature of DTA curve of mixed powder.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.293-298
• /
• 2003

In this study, tensile adhesive strength(TAS) test was carreid out for evaluated the effects of temperature conditions(-20, -10, 5, 20, 30, $40^{\circ}C$) on the tensile adhesive characteristics about six waterproofing membranes which were commercially used in bridge decks. And, failure appeariences of waterproofing systems in each temperature were investigated and observed the sawing surfaces of waterproofing systems for whether or not damaged of waterproofing membranes. TAS test results were increased when test temperature was decrease in all waterproofing membrane. The type of failure was ductile in $30^{\circ}C$ and $40^{\circ}C$, but brittle failure below $20^{\circ}C$. This results were shown that if temperature above $30^{\circ}C$ is continued for a long time, waterproofing material will be damaged by softening and a part of membranes were damaged by hot aggregate in SMA. So we will consider the type of asphalt for choice of the waterproofing membranes.

• 한국자원식물학회지
• /
• 제14권2호
• /
• pp.175-181
• /
• 2001

잔디의 종자번식에서의 가장 큰 문제점은 종자의 휴면으로 인한 발아율 불량이라 할 수 있다. 파종전종자처리를 통하여 잔디종자의 발아율 불량을 극복하기 위한 기존의 종자처리 모형을 더욱 보완하고자 종피연화, 저온, 건조 처리를 처리중 또는 발아과정의 빛조건과 연계하여 이들 처리가 발아율에 미치는 영향을 추적하고자 본 연구를 실시하였던 바 그 결과를 요약하면 다음과 같다. 1. 발아율은 NaOH로 종피연화 처리된 종자의 발아중 적색 LED와 백열등으로 조사할 경우 암상태로 유지하는 것보다 높은것으로 조사되었다. 2. 발아율은 종피연화 처리된 종자를 건조하는 것이 건조를 하지 않은 것보다 높았던 반면, 건조중 처리 되는 적색광, 형광등, 암처리 간에는 차이가 없었다. 3. 발아율은 종피연화 처리된 종자를 2~3주간의 저온 처리후 초적색광에 비하여 적색광의 비율이 많은 형광등으로 조사하면서 건조하는 것에서 발아율이 가장 높았다. 4. 평균발아율은 H$_2$SO$_4$8M에 처리하는 것이NaOH, KOH, acetone 각 20%에 처 리 하는 것보다 높았으나 특정 처리의 발아율로는NaOH20%에 30분간 처리하는 것에서 가장 높았다. 5. 처리된 종자가 노지에 무피복으로 파종되는 조건을 고려할 경우 NaOH 20%에 30분간 종피 연화를 실시하여 세척한 다음 2주정 도 저온처리를 가한 종자를 35$^{\circ}C$에 4시간 형광등으로 조사하면서 건조하는 것으로 기존 잔디 종자의 파종전처리 모형을 보완하였다.

• 대한기계학회논문집
• /
• 제6권2호
• /
• pp.101-106
• /
• 1982

This study was undertaken to determine tensile properties and low-cycle fatigue behavior of 0.6%C high carbon steel used of structural purposes at temperatures up to 500.deg.C. In the low-cycle fatigue test the upper limit was decided by elongation(i.e. the total strain range), while the lower limit was defined by the load (i.e. zero load). The following results were obtained. Both, the ultimate tensile strength and low-cycle fatigue resistance attain the maximum values near 250.deg.C. Above this temperature the values decrease rapidly as the temperature increases. The low-cycle fatigue resistance decreases whenever there is an increase of the total strain range. Because the hardness of cycle fatigued specimen correlates cyclic hardening and cyclic softening, therefore the hardness of cycle fatigued specimen is smaller than that of the nonfatigued specimen at room temperature and 500.deg.C but much larger than the hardness of the nonfatigued specimen near 250.deg.C.

• 한국세라믹학회지
• /
• 제29권6호
• /
• pp.451-458
• /
• 1992

Dense glass-ceramics for low firing temperature substrate were prepared by addition of CeO2 flux to the glass of MgO-Al2O3-SiO2 system. Glass powders were fabricated by melting at 150$0^{\circ}C$ and ball milling. Glass powder compacts were sintered at 800~100$0^{\circ}C$ for 3h. The crystallization and the shrinkage behaviors of glass powder compacts were analyzed by XRD, DTA and TMA. The shrinkage of glass powder compact increased with increasing the amount of CeO2. Because the softening temperature decreased and the crystallization temperature increased with increasing the amount of CeO2. Apparently, addition of CeO2 prevented formation of $\mu$-cordierite phase from the glass-ceramics and improved formation of $\alpha$-cordierite phase. Therefore crystallization properties were enhanced.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.36-39
• /
• 2002

Polycrystalline silicon (poly-Si) thin film transistor (TFT) technology is emerging as a key technology for active matrix liquid crystal displays (AMLCD), allowing the integration of both active matrix and driving circuit on the same substrate (normally glass). As high temperature process is not used for glass substrate because of the low softening points below 450$^{\circ}C$. However, high temperature process is required for getting high crystallization volume fraction (i.e. crystallinity). A poly-Si thin film transistor has been fabricated to investigate the effect of high temperature process on the molybdenum (Mo) substrate. Improve of the crystallinity over 75% has been noticed. The properties of structural and electrical at high temperature poly-Si thin film transistor on Mo substrate have been also analyzed using a sputtering method

• 한국세라믹학회지
• /
• 제30권2호
• /
• pp.148-156
• /
• 1993

TiN films were deposited onto high speed steel (SKH9) by plasma assisted chemical vapor deposition (PACVD) using a TiCl4/N2/H2/Ar gas mixture at around 50$0^{\circ}C$. The effects of the deposition temperature, R.F. power and TiCl4 concentration on the deposition of TiN and the microhardness of TiN film were investigated. The crystallinity and the microhardness of TiN films were improved with increase of the deposition temperature. Optimum deposition temperature in this study was 50$0^{\circ}C$, because a softening or phase transformation of the substrate occurred over 50$0^{\circ}C$. A large increase of the film growth rate with a strong(200) preferred orientation was obtained by increasing R.F. power. Much chlorine content of about 10at.% was found in the deposited films and resulted in relatively low average microhardness of about 1, 500Kgf/$\textrm{mm}^2$ compared with the theoretical value(~2, 000Kgf/$\textrm{mm}^2$).

• 한국분말재료학회지
• /
• 제7권3호
• /
• pp.131-136
• /
• 2000

The effect of tempering temperature on the three point bending fatigue behavior of a P/M high speed steel JYPS-23 (1.28% C, 4.20% Cr, 6.40% W, 5.00% Mo, 3.10% V, bal. Fe) was investigated. The number of cycles to failure of the specimen austenitized at $1175^{\circ}C$ drastically increased with increasing tempering temperature. As tempering temperature increased from 500 to $620^{\circ}C$, the volume fraction and average size of carbides (MC or M6C) did not significantly changed, while hardness decreased drastically. The reduced hardness is due to the softening of matrix, which increased the resistance of the fatigue crack propagation. For a practical application, powder compacting test were also conducted with the P/M high speed steel punches tempered at 500, 580, and $620^{\circ}C$. The number of compacting cycles to failure of the punches also increased with increasing tempering temperature.

• Journal of Ginseng Research
• /
• 제25권3호
• /
• pp.122-126
• /
• 2001

수삼을 물로 세척한 후 한 뿌리씩 연포장재 필름 주머니(ONY/LDPE/L-LDPE, 200$\times$300mm, 90$\mu\textrm{m}$)에 넣고 밀봉하여 $25^{\circ}C$, 1$0^{\circ}C$ 또는 4$^{\circ}C$에서 저장하면서 외관품질과 개체무게를 조사한 결과 수삼의 외관품질은 저장온도에 관계없이 주로 연화에 의하여 불량해졌으며 외관품질 변화 속도상수와 저장온도의 역수뿐만 아니라 개체무게 변화속도상수와 저장온도의 역수간에도 각각 5% 유의수준에서 양호한 직선관계를 나타내었다. 따라서 $25^{\circ}C$에서의 온도학대시험을 통하여 저온에서 저장중인 개별포장 수삼의 저장수명 및 개체무게 변화율을 단기간에 예측할 수 있을 것으로 판단된다.