• Journal of the Korean Wood Science and Technology
• /
• v.13 no.1
• /
• pp.19-62
• /
• 1985

This study was performed to investigate: (i) the bending processing properties of silk worm oak (Quercus acutissima Carr.) and Korean red pine (Pinus densiflora S. et Z.) by boiling and steaming treatments; (ii) the effects of interrelated factors - sapwood and heartwood, annual ring placement, softening temperature and time, moisture content. and wood defects on bending processing properties; (iii) the changing rates of bending radii after release from a tension strap, and (iv) the improving methods of bending process by treatment with chemicals. The size of specimens tested was $15{\times}15{\times}350mm$ for boiling and steaming treatments and $5{\times}10{\times}200mm$ for treatments with chemicals. The specimens were green for boiling treatments and dried to 15 percent for steaming treatments. The specimens for treatments with chemicals were soaked in saturated urea solution, 35 percent formaldehyde solution, 25 percent polyethylene glycol -400 solution, and 25 percent ammonium hydroxide solution for 5 days and immediately followed the bending process, respectively. The results obtained were as follows: 1. The internal temperature of silk worm oak and Korean red pine by boiling and steaming time was raised slowly to $30^{\circ}C$ but rapidly from $30^{\circ}C$ to $80-90^{\circ}C$ and then slowly from $80-90^{\circ}C$ to $100^{\circ}C$. 2. The softening time required to the final temperature was directly proportional to the thickness of specimen. The time required from $25^{\circ}C$ to $100^{\circ}C$ for 15mm-squared specimen was 9.6-11.2 minutes in silk worm oak and 7.6-8.1 minutes in Korean red pine. 3. The moisture content (M.C.) of specimen by steaming time was increased rapidly first 4 minutes in the both species, and moderately from 4 to 20 minutes and then slowly and constantly in silk worm oak, and moderately from 4 to 15 minutes and then slowly and constantly in Korean red pine. The M.C. of 15mm-squared specimen in 50 minutes of steaming was increased to 18.0 percent in the oak and 22.4 percent in the pine from the initial conditioned M.C. of 15 percent The rate of moisture adsorption measured was therefore faster in the pine than in the oak. 4. The mechanical properties of the both species were decreased significantly with the increase of boiling rime. The decrement by the boiling treatment for 60 minutes was measured to 36.6-45.0 percent in compressive strength, 12.5-17.5 percent in tensile strength, 31.6-40.9 percent in modulus of rupture, and 23.3-34.6 percent in modulus of elasticity. 5. The minimum bending radius (M.B.R.) of sapwood and heartwood was 60-80 mm and 90 mm in silk worm oak, and 260 - 300 mm and 280 - 300 mm in Korean red pine, respectively. Therefore, the both species showed better bending processing properties in sapwood than in heartwood. 6. The M.B.R. of edge-grained and flat-grained specimen in suk worm oak was 60-80 mm, but the M.B.R. in Korean red pine was 240-280 mm and 260-360 mm, respectively. Comparing the M.B.R. of edge-grained with flat-grained specimen, in the pine the edge-grained showed better bending processing property than the flat-grained. 7. The bending processing properties of the both species were improved by the rising of softening temperature from $40^{\circ}C$ to $100^{\circ}C$. The minimum softening temperature for bending was $90^{\circ}C$ in silk worm oak and $80^{\circ}C$ in Korean red pine, and the dependency of softening temperature for bending was therefore higher in the oak than in the pine. 8. The bending processing properties of the both species were improved by the increase of softening time as well as temperature, but even after the internal temperature of specimen reaching to the final temperature, somewhat prolonged softening was required to obtain the best plastic conditions. The minimum softening time for bending of 15 mm-squared silk worm oak and Korean red pine specimen was 15 and 10 minutes in the boiling treatment, and 30 and 20 minutes in the steaming treatment, respectively. 9. The optimum M.C. for bending of silk worm oak was 20 percent, and the M.C. above fiber saturation point rather degraded the bending processing property, whereas the optimum M.C. of Korean red pine needed to be above 30 percent. 10. The bending works in the optimum conditions obtained as seen in Table 24 showed that the M.B.R. of silk worm oak and Korean red pine was 80 mm and 240 mm in the boiling treatment, and 50 mm and 280 mm in the steaming treatment, respectively. Therefore, the bending processing property of the oak was better in the steaming than in the boiling treatment, but that of the pine better in the boiling than in the steaming treatment. 11. In the bending without a tension strap, the radio r/t of the minimum bending radius t to the thickness t of silk worm oak and Korean red pine specimen amounted to 16.0 and 21.3 in the boiling treatment, and 17.3 and 24.0 in the steaming treatment, respectively. But in the bending with a tension strap, the r/t of the oak and the pine specimen decreased to 5.3 and 16.0 in t he boiling treatment, and 3.3 and 18.7 in the steaming treatment, respectively. Therefore, the bending processing properties of the both species were significantly improved by the strap. 12. The effect of pin knot on the degradation of bending processing property was very severe in silk worm oak by side, e.g. 90 percent of the oak specimens with pin knot on the concave side were ruptured when bent to a 100 mm radius but only 10 percent of the other specimens with pin knot on the convex side were ruptured. 13. The changing rate in the bending radius of specimen bent to a 300 mm radius after 30 days of exposure to room temperature conditions was measured to 4.0-10.3 percent in the boiling treatment and 13,0-15.0 percent in the steaming treatment. Therefore, the degree of spring back after release was higher in the steaming than in the boiling treatment. And the changing rate of moisture-proofing treated specimen by expoxy resin coating was only -1.0.0 percent. 14. Formaldehyde, 35 percent solution, and 25 percent polyethylene glycol-400 solution found no effect on the plasticization of the both species, but saturated urea solution and 25 percent ammonium hydroxide solution found significant effect in comparison to non-treated specimen. But the effect of the treatment with chemicals alone was inferior to that of the steaming treatment, and the steaming treatment after the treatment with chemicals improved 10-24 percent over the bending processing property of steam-bent specimen. 15. Three plasticity coefficients - load-strain coefficient, strain coefficient, and energy coefficient - were evaluated to be appropriate for the index of bending processing property because the coefficients had highly significant correlation with the bending radius. The fitness of the coefficients as the index was good at load-strain coefficient, energy coefficient, and strain coefficient, in order.

• Journal of the Korean Chemical Society
• /
• v.12 no.2
• /
• pp.65-80
• /
• 1968

The physico-chemical properties of nine selected thallium borosilicate glasses and other 21 supplementary compositions were investigated. Their composition-property curves are found to be in many respects analogous to those of other borosilicate glasses containing lithia, soda, and lead oxide. It is indicated that certain minima found in the composition-property curves of thallium borosilicate glasses might be caused by a change in boron coordination as has been observed to occur in the $Na_2O-B_2O_3-SiO_2$ glasses. Typical effects of thallium ions on the borosilicate glass are summarized as follows: 1) Addition of thallium ions increased density, refractive index, water solubility, linear coefficient of thermal expansion, and dielectric constant. 2) Increased concentration of thallium decreased the softening point of the glasses, caused fluorescence under ultraviolet radiation and smeared out the absorption edges up to $15{\mu}$ in the infrared region. An extensive liquid immiscibility was found by replication electron microscope technique in the $Tl_2O-B_2O_3-SiO_2$ system. The immiscibility covers a composition range roughly from 55 wt. % Tl2O to the binary system $B_2O_3-SiO_2.$ By acid treatment, it was found that the immiscible glass consists of separate silica-rich and boron-rich phases.

• Food Science and Preservation
• /
• v.20 no.6
• /
• pp.766-774
• /
• 2013

The effect of storage temperatures ($0^{\circ}C$and $20^{\circ}C$) and packing functional film for fruit quality were examined in 'Fuyu' persimmon. The fresh weight loss was delay more effectively by the inhibition of transpiration when functional film was used. The firmness was effectively maintained in functional film packages at low temperature ($0^{\circ}C$), which might result from the beneficial combination of $CO_2$ and $O_2$. The soluble solid contents was higher with packing of functional film at $0^{\circ}C$ than at room temperature ($20^{\circ}C$). Highest $CO_2$ production in functional film bags was observed in room temperature storage after one week and thereafter declined sharply whereas lowest in 8 weeks. $CO_2$ concentration regardless of packing slowly increased to $5.2{\mu}L{\sim}10.2mL{\cdot}kg^{-1}{\cdot}h^{-1}$ until 8 weeks of low temperature due to persimmon respiration. Hunter 'b' value changed greatly yellowness according to temperature of storage but there were no significant differences among packaging treatments. Effects of functional film and low temperature in slower softening were consistent. This results suggested that the packing functional film at low temperature resulted in the best retention of quality market.

• Geomechanics and Engineering
• /
• v.21 no.5
• /
• pp.433-445
• /
• 2020

The weakening and softening behavior of soft clay subjected to cyclic loading due to the build-up of excess pore water pressure is well-known. During the design stage of the foundation of highways and coastal high-rise buildings, it is important to study the mechanical behavior of marine soils under cyclic loading as they undergo greater settlement during cyclic loading than under static loading. Therefore, this research evaluates the cyclic stress-strain and shear strength of untreated and treated marine clay under the effects of wind, earthquake, and traffic loadings. A series of laboratory stress-controlled cyclic triaxial tests have been conducted on both untreated and treated marine clay using different effective confining pressures and a frequency of 0.5 and 1.0 Hz. In addition, treated samples were cured for 28 and 90 days and tested under a frequency of 2.0 Hz. The results revealed significant differences in the performance of treated marine clay samples than that of untreated samples under cyclic loading. The treated marine clay samples were able to stand up to 2000 loading cycles before failure, while untreated marine clay samples could not stand few loading cycles. The untreated marine clay displayed a higher permanent axial strain rate under cyclic loading than the treated clay due to the existence of new cementing compounds after the treatment with recycled tiles and low amount (2%) of cement. The effect of the effective confining pressure was found to be significant on untreated marine clay while its effect was not crucial for the treated samples cured for 90 days. Treated samples cured for 90 days performed better under cyclic loading than the ones cured for 28 days and this is due to the higher amount of cementitious compounds formed with time. The highest deformation was found at 0.5 Hz, which cannot be considered as a critical frequency since smaller frequencies were not used. Therefore, it is recommended to consider testing the treated marine clay using smaller frequencies than 0.5 Hz.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.33 no.3
• /
• pp.553-559
• /
• 2004

This study was carried out to estimate the effects of glucono-$\delta$-lacton (GDL) on prolongation of shelf-life on Kimchi. Final concentration of added GDL was determined 0.3% according to the result of sensory evaluation. Chemical characteristics and microbiological parameters were monitored during fermentation at 1$0^{\circ}C$. GDL Kimchi showed the initial sharp decrease in pH and gradually increase of pH due to osmotic pressure and then the pH of GDL Kimchi was slowly decreased compared with that of control Kimchi during fermentation. The acidity of control Kimchi was markedly increased around pH 4.5 by growth of microorganism. Otherwise, GDL Kimchi showed that t]le formation of organic acids was slow and little amount compared with that of control Kimchi. HPLC analysis showed oxalic acid, lactic acid, acetic acid, malic acid and succinic acid appeared by fermentation. The production of lactic acid changed a lot in control Kimchi, where as little in GDL Kimchi. Growth of L. mesenteroides at initial stage of Kimchi fermentation was remarkably inhibited by adding 0.3% GDL. It retarded also the growth of L. Plantarum and L. breuis at late stage of Kimchi fermantation and led to reduce the softening of texture and retard over ripening of Kimchi. Tn sensory evaluation of Kimchi, GDL Kimchi showed the similar characteristics to the control Kimchi. This result suggested that GDL can be successfully used for the prolongation of shelf-life and sensory evaluation on Kimchi.

• Applied Biological Chemistry
• /
• v.46 no.1
• /
• pp.39-45
• /
• 2003

This study was conducted to investigate the effect of ash contents of bread flour on the rheology of frozen dough In making frozen dough by measuring amylograph, flrinograph and extensograph. The quality of frozen-stored dough under freezing condition ($-20^{\circ}C$, 12 weeks) was evaluated by measuring final proof time, moisture content, baking loss, loaf volume and hardness of bread with storage time. In bread flour with high ash content farinogram showed that water absorption, degree of softening increased but valorimeter value decreased. In bread flour with low ash content amylogram showed that gelatinization temperature and maximum viscosity increased and extensogram showed that the area and resistance of the bread flour increased. As the proof time increased the extensibility decreased. Final proof time of frozen dough was shortened at the bread flour with low ash content with storage time. In bread using the flour with high ash content, moisture content, increased but baking loss rate decreased while the hardness of product increased slowly with time. But in bread using the flour with low ash content, the loaf volume of baking increased but the hardness of product decreased. As the frozen storage time was shortened, the product was more stable and better in quality.

• Journal of the Korea Concrete Institute
• /
• v.24 no.1
• /
• pp.25-35
• /
• 2012

For a member subjected to direct shear forces, forces are transferred across interface concrete area and resisted by shear transfer capacity. Shear-friction equations in recent concrete structural design provisions are derived from experimental test results where shear-friction capacity is defined as a function of steel reinforcement area contained in the interface. This empirical equation gave too conservative values for concrete members with large amounts of reinforcement. This paper presents a method to evaluate shear transfer strengths and to define ultimate conditions which result in crushing of concrete struts after yielding of longitudinal reinforcement perpendicular to the interface concrete. This method is based on the bi-axial stress field theory where different constitutive laws are applied in various means to gain accurate shear strengths by considering softening effects of concrete struts based on the modified compression-field theory and the softened truss model. The validity of the proposed method is examined by applying to some selected test specimens in literatures and results are compared with recent design code provisions. A general agreement is observed between predicted and measured values at ultimate loading stages in initially uncracked normal-strength concrete test.

• Applied Biological Chemistry
• /
• v.41 no.3
• /
• pp.228-233
• /
• 1998

The storage life of satsuma mandarin(Citrus unshiu Marc. var. miyagawa) by the various pretreatment of temperatures; non-treated, room temperature, $10,\;20^{\circ}C$ and $35^{\circ}C$ were investigated. The pretreated citrus fruits were stored at $4^{\circ}C$, 85% relative humidity. Weight loss of citrus fruits by the pretreatment at $35^{\circ}C$ for 24 hrs was the lowest among that of others. Decay ratio of $35^{\circ}C$ pretreated fruits was increased at initial stages of storage, but was maintained low level after that, compared to other treatments. After 115 days storage, firmness of fruits was lowered by the softening, and decayed fruits were occurred increasingly. Ethylene evolution was increased between $55{\sim}65$ days after storage, and the amount was increasing rapidly after 115 days. It seemed to be derived from decayed fruits and physiological activities. $CO_2$ content in fruit was decreased at initial stages of storage, but was increased between $55{\sim}100$ days during storage periods. Acid content, soluble solids, total sugar and vitamin C were reduced gradually during cold storage, but the difference among treatments was not so great. Pretreated fruits at $35^{\circ}C$ for 24 hrs before cold storage was effective on preventing from weight loss and respiration ratio. Optimum storage period of early variety of Satuma mandarin was regarded for 100 days on the basis of appeareance and taste.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.256-261
• /
• 2017

The effects of temperature and length of cold storage on the quality maintenance of fresh "Gold" kiwifruit were investigated. Physio-chemical properties were analyzed in kiwifruit held at $2^{\circ}C$ and $6^{\circ}C$ temperatures compared to fruit at room temperature ($20{\sim}28^{\circ}C$) during 8 weeks of storage. Low temperatures ($2^{\circ}C$ and $6^{\circ}C$) significantly delayed softening and soluble solids content (SSC) accumulation compared to higher temperature ($20{\sim}28^{\circ}C$). Physico-chemical properties of fruits, including weight losses, firmness, SSC, titratable acidity (TA), SSC/TA ratio, and flesh color properties were monitored during storage. Fast firmness loss was detected in fruit stored at higher temperatures compared to low temperature ($2^{\circ}C$). Similar results were observed for acidity according to storage temperature and length of cold storage, whereas SSC increased to the limited values (%Brix) during storage. The soluble solids content (SSC) increased markedly during the first 60 days of storage and remained almost constant thereafter for all treatments. SSC accumulation rates decreased from 5 weeks after storage probably due to differences between initial and ripe kiwifruits, and SSC decreased with each passing week due to natural starch conversion over time. The SSC/acid ratio increased from 18 to 27 until 5 weeks after storage and then slowly declined in all kiwifruit stored at different low temperatures. Sensory evaluation results showed no differences in kiwifruit flesh color stored at two storage temperatures of $2^{\circ}C$ and $6^{\circ}C$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.5
• /
• pp.246-254
• /
• 2013

Translucent opal glass was fabricated in order to substitute polycarbonate diffuser of LED lighting for the purpose of improving the durability problem. Calcium phosphate was used for the opacifier of opal glass and melted at $1550^{\circ}C$ for 2 hrs in electric furnace. Because opal glass was made by phase separation and growth of opacifier grains during cooling procedure after forming of melted glass, we identified the effect of opaque properties by the change of forming and cooling temperature, as R.T. (room temperature), $850^{\circ}C$, $1100^{\circ}C$ and $1200^{\circ}C$. As the results, it had excellent optical properties for the diffuser of LED lighting in the fabricated sample of forming and cooling at $1200^{\circ}C$, with no dazzling from direct light by high haze value over 82 % and low parallel transmittance value under 10 %. For the thermal properties, it had expressed thermal expansion coefficient of $6.352{\times}10^{-6}/^{\circ}C$ and softening point of $839^{\circ}C$.